4R75W Transmission pump removal and disassemble 2005 Ford F-150

[@TN_Travesty]

Your knowledge and man-handling of that transmission earned a Sub.

[@bama1fan]

Watching this video was awesome! I have a 2004 F150 I had to have the transmission rebuilt because I lost my overdrive. Didn’t realize that a transmission has so many moving parts! Great video!

[@jwm6314]

The bolts that mate the bellhousing to the engine also thread into the two oversize threaded holes in the pump housing. You can tune in tokyo and pull it by hand or slide hammer on the head with light taps.

[@justinyoungstown]

Thank you, just pulled a f350 5.4 motor that was locked up from a main bearing. So had to pull the converter as well. When the motor locked up it snapped the output shaft tip off so had to pull the pump. Only realized this when replacing the seal. Good thing I checked. Hoping after I replace the pump all else is well. I welded a bolt to a slide hammer and got it out that way.

[@caseykelso8409]

How and when do I put the anti clunk spring in n how does it go and or rest .. I have the round spring looking one.. 05 Ford f150 ..

[@mukluck]

You need to do more videos. Great job explaining the process with additional information on part's that are commonly problematic. Speaking of problem parts. Do the main ravigneaux pinion carrier (planetary) have a reputation for failure on these transmission? Would it be safe to replace/rebuild the unit anyway or just check to make sure it's within spec and throw it back in?

[@jmoxey74]

Want to know if the front pump on a 2005 can work on a 2007 f150 also ?

[@lestrev5602]

2004 grand marquis is the same transmission sir??

[@gavintyson3033]

That’s a 4R75E bc a 75W is a wide ratio transmission and only has one speed sensor on the driver side. The 75E on the other hand has two speed sensors on the driver side as you see on the transmission in the video

[@davidsaylor3582]

This was A Very helpful video....I'm Getting my 2006 Ford f-150 325,000+ miles Rebuilt hopefully this week 😉

[@efijemuehphilip542]

Hi, thanks for your video. Please what would make a tranny not to move in drive and 2 position but only in L and reverse. Thanks for your response

[@jasonparker8489]

I’m having trouble finding a pump for a 4R70w

[@2491kridge]

Part of the pump where the torque converter slides in you have that brass sleeve, is that replaceable by itself and if so then how would it come in and out, or do you have to replace the whole pump. I’ve got one where the brass sleeve has a crack in it and it’s pissing fluid from the seal area

[@tigertransmissions]

2491kridge Yes the pump bushing is definitely replaceable. It has a oil groove when you replace it make sure it’s in the same spot.

[@2491kridge]

joshua white do you need any special tools? Can you take it out from the front and put it back in or do you have to take the pump assembly out to do it? And do you think a tiny little micro crack in that brass piece would be enough to cause a massive leak like it is?

[@mathewpike2581]

Slam!!!!!!!!!!!! Here's this Slam!! and don't forget this don't break this ........slammmm!!!!!!!!!! lmao

[@halleffect1]

i know, even worse with a slight hangover. I'm trying to hear what he's saying, then slam!

[@dalebeck3411]

Got a question on a electronics pressure solenoid transmission is does that come in two pieces or is it one piece solenoid somehow to the movement of the overdrive send me a text add a picture showing me how to take it out how's the transmission if not if it's a two piece that is done the way I think it is I don't know that I might can help myself for I don't have $2,000 to get somebody else to go into it it's a good band 21 years old going in 21 years old I bought it brand-new 36,000 miles on it that's all

[@MrPancho728]

I want to make my 06 Ford F-150 2wd into a 4x4 the 2wd transmission is in great shape. I am planning on getting a donor 4x4 would it be best to change out the transmission or swap out the end shaft. I am not a mechanic to work inside a engine or transmission but I can yank them out and install 🤷🏻‍♂️ you make it look easy on a scale from 0 to 10 and 10 being the hardest job what would you think it would be?

[@outdoordaily6463]

Yea where does that anti rattle clip tho. Idk why you didn’t show us here it would’ve been so easy.

[@halleffect1]

nice video, but what spoils it is the loud clunking sounds. i know you're not abusing the parts, it's most likely the mic location. should be clipped on your shirt close to your mouth, that way we can hear what you're saying without the slamming sounds. I found myself cranking the volume knob up/down the whole time. but don't take it wrong, I really appreciate you sharing this information.

[@stevehuey3652]

I've just replaced my 2004 f150 transmition with a upgraded Detroit axle transmition rebuild I'm getting a wineing noise when accelerating does any one know what it could be

[@dano198]

i used one of their rebuilds on my 05 it lasted less than 500 miles. detroit axel stopped returning my emails i had to file a paypal claim

[@bartolomemiro9004]

hola donde es su taller?

[@tigertransmissions]

Lebanon, Tennessee

[@ezwa9979]

U just kept tossing evrEthing aside randomly, wat wud rElE hav Bn funE, is if you just stRtd floPing all the pRts randomley back Ovr Ur sholders to hU nOz where?😅(NEwA thNx 4 the lSN on hoO 2 tAk apRt a trNsmission, Ql, I still hav no clU how to put 1 bak 2gethr)..

[@ezwa9979]

thumbs up cause the humor

[@HueToobBlows]

NOw I understand why Lee Miles Transmissions suck.