{502} Why IGBT Burns Out After Replacement - IGBT Damaging Reasons

  Рет қаралды 42,499

Haseeb Electronics

Haseeb Electronics

Күн бұрын

Пікірлер: 177
@arpir97
@arpir97 2 жыл бұрын
For better result: 1) Always check the ESR of the resonant capacitor and the internal insulation. 2) Remove all flux residue with a little brush and pure alcohol. 3) Apply electronic silicone to the solder pins of the IGBT and the driver on both sides of the PCB to prevent moisture in the air from activating the gate of the transistor.
@HaseebElectronics
@HaseebElectronics 2 жыл бұрын
it is really a great addition, i am personally thankful for a valuable guideline for my viewers please accept my best regards
@taimsamman1570
@taimsamman1570 Жыл бұрын
ما شاء الله انت كنز من المعلومات ...لقد فاجئتني عندما تكلمت باللغة العربية ....لم اجد ابدا بكل المحتوى العربي شخص بارع وضليع بالالكترونيك مثلك ..كم نحتاجك لو كان عندك قناة تتكلم فيها بالعربي ..
@rogerschelling5668
@rogerschelling5668 3 жыл бұрын
Thank you for explaining this is detail! I have also found it it frustrating to get reliable results when changing high power components. I always figured there was another component or "something". This video detail is very helpful for understanding what else is happening. Very well done as usual.
@MarkPrince1317
@MarkPrince1317 3 жыл бұрын
That is really very very informative now I understand what's the reason of burning MOSFETs and IGBT thank you so much for the very informative and easy understandable videos Best regards from Philippines 🇵🇭
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@fideliskabwe5380
@fideliskabwe5380 Ай бұрын
Thanks,good explanation. I've been losing igbts in inveters a lot nowadays from clients homes.
@omiza3416
@omiza3416 2 ай бұрын
Mr. Mohamet is superb teacher
@donupanandaamarasinghe1640
@donupanandaamarasinghe1640 2 жыл бұрын
Thanks lot for your genuine effort to share your valuable knowledge. My sincere blessings
@realpower9ir
@realpower9ir 3 жыл бұрын
One of the most important points that should be consider is: to recognize "Counterfeit" Components from the "Original" ones. Counterfeit components make us "CONFUSE"
@kuchpanktiyajindagiki
@kuchpanktiyajindagiki 3 жыл бұрын
Good evening brother. Though I don't understand the technical things, but always like your presentation and way of explaining
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Thank you very much dear sister it is your greatness
@janasmeal7916
@janasmeal7916 3 жыл бұрын
ma shaa Allah fabulous informative discussion on igbt failures. your analysis is always effective in electronics work. stay blessed dear brother
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Many many thanks dear sister
@arpir97
@arpir97 2 жыл бұрын
@@HaseebElectronics thank you, Mr. Haseeb, you are a very respected and good person, You explain schemes and theories very well and nicely, I often watch your recommendations on your channel.
@elavarasanputhinan772
@elavarasanputhinan772 3 жыл бұрын
Best explanation sir.... Today only i know, purpose of zero current detection... Thank you very much sir... God always prosperity in your life...
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
You are most welcome it is my pleasure that my efforts are useful
@henryalcantara5647
@henryalcantara5647 2 жыл бұрын
very well explained, bravo sir🏅🏅🏅you made technical books easy to understand and interpret
@HaseebElectronics
@HaseebElectronics 2 жыл бұрын
best regards and special thanks for your valuable comment
@levit1803
@levit1803 2 жыл бұрын
Your video was very helpful. I had changed in a mini welder the Igbt's because they burned out and one of the new one was always to hot 115 degrees Celsius one had approx 70kohm internal resistence and the other one approx 650kohm and that's why was to hot. Thanks a lot, you make a wery good job.
@HaseebElectronics
@HaseebElectronics 2 жыл бұрын
wow that is really awesome i am thankful for your valuable comment, to encourage my efforts
@saicharan8696
@saicharan8696 3 жыл бұрын
Super explanation, thank you very much, iam from India, Hyderabad, thank you 🙏💕, do more such videos
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot dear you are most welcome
@qaiserqureshi100
@qaiserqureshi100 3 жыл бұрын
Amazingly useful information Big Like from London 🇬🇧💌
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
big thanks and special thanks
@t1d100
@t1d100 3 жыл бұрын
Excellent teaching. Thank you, Haseeb.
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
You are most welcome
@QARepair
@QARepair Жыл бұрын
You are a very clever man, thank you for your videos
@robbirobson7330
@robbirobson7330 3 жыл бұрын
I also recommend to use a transistor tester before you install the part so you can check the capacitance and vge. This goes also if you have a bunch of transistors you need to change, test them all and select the ones that are close in value. With all these chinese parts now sometimes there are defective parts or out of spec. Always test before install.
@sopuluchukwuanthony9041
@sopuluchukwuanthony9041 7 ай бұрын
Pls my igbt keep burning out even when I put higher number
@zakiausa
@zakiausa 3 жыл бұрын
Salam brother you showing good work and telling god bless you by 🇺🇸🙋‍♀️
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot dear sister
@SulemaniaProduction
@SulemaniaProduction 3 жыл бұрын
MashaAllah Great Sharing 🌹🌹❤👍
@mtrltoolman
@mtrltoolman 3 жыл бұрын
جزاك الله خير . لقد تعلمت اشياء جديدة لم اكن اعرفها . شكراً جزيلاً يا استاذ.
@sworgam
@sworgam Жыл бұрын
excellent class very clearly explained
@HaseebElectronics
@HaseebElectronics Жыл бұрын
it is my pleasure
@saleemkhan-mx9jw
@saleemkhan-mx9jw 2 жыл бұрын
Very useful fault finding method. Thanks
@HaseebElectronics
@HaseebElectronics 2 жыл бұрын
You're welcome
@lupojacobo9892
@lupojacobo9892 3 жыл бұрын
Very informative like always. Shukriya Maestro.
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
So nice of you
@lupojacobo9892
@lupojacobo9892 3 жыл бұрын
@@HaseebElectronics Maestro can you make a video explaining the meaning of connection or how does the KCM15F60GA IC works thi Ic comes in Samsung washers motor inverters please
@gopalraovellanki9826
@gopalraovellanki9826 3 жыл бұрын
Hi sir..,very interested and informative video. Thank you very much. Have a good day 🙏
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot dear
@vlogdiaries4u
@vlogdiaries4u 3 жыл бұрын
Masha Allah informative as always..
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Many many thanks
@CuisineWithShahida
@CuisineWithShahida 3 жыл бұрын
MashaAllah very useful info Nice sharing👍
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot dear sister
@mehranmohamad6924
@mehranmohamad6924 5 ай бұрын
hello dear brother. i wish he would explain how to calculation the capacitor connected to the coil. yiu are unique in the world of electronics
@tyronearendse1722
@tyronearendse1722 3 жыл бұрын
Hi thanks for the informative video and for the preventative ways to avoid components being destroyed
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
You are welcome! it is my pleasure stay blessed
@carolinediyandvlog
@carolinediyandvlog 3 жыл бұрын
Fantastic video 😌 big like
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Big thanks
@Babaa51
@Babaa51 2 жыл бұрын
Thanks for your support. However there are two thermistors in the circuit for over Temperature. So when the IGBT overheats then the Microcontroller is supposed to switch off, can you throw some light on this? Thanks.
@collinsmurambiwa146
@collinsmurambiwa146 3 жыл бұрын
Very helpful information, most appreciated
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@muhammadishtiaq24
@muhammadishtiaq24 3 жыл бұрын
Helpful and informative video
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot stay blessed
@AIexanderHartdegen
@AIexanderHartdegen 2 жыл бұрын
When I saw this, I think first at the fake component avalaible on ebay and aliexpress. They are sometimes rebranded, and gate capacitance is not the same, and bandwitdh is different. THis is the reason why it works few hours, and failed when overheating. If the capacitor of the LC circuit is dead, you will maybe just have a lack of effeciency. Thanks for the video, god bless you.
@vyshakhp8802
@vyshakhp8802 3 жыл бұрын
You are amazing brother.🧡
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Thank you so much 😀
@Whosewillwin
@Whosewillwin 3 жыл бұрын
The video is informative, thanks for sharing.
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@Aaaaaasssssss382
@Aaaaaasssssss382 3 жыл бұрын
السلام عليكم و رحمة الله جعل الله لك هذا العمل في ميزان حسناتك يوم القيامة. Excellent explanation. I hope you do a design example with testing experiment of an induction heater. I am very interesting with induction heater, it is very tricky.
@vijayakumarkumar9190
@vijayakumarkumar9190 3 жыл бұрын
Very useful information sir thanks for sharing this knowledge to us
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
it is my pleasure
@electronicasolutions9813
@electronicasolutions9813 Жыл бұрын
una pregunta el datasheet q tomas como referencia a que igbt (numeración ) pertenece. muy buena explicación
@hightttech
@hightttech 3 жыл бұрын
Very GOOD video, Sir. Sourcing components is HUGE issue. Too much falsely marked JUNK from non-authorized-distributors. Sometimes seems quicker or cheaper, but not really; and clients get mad when equipment down over and over. Now, in USA, i ONLY buy from Digikey and Mouser. Clients and me are happy to get OE performance out of repaired equipment.
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot and lovely thanks you are absolutely right that component sourcing and falsely marked components are biggest headache and loss of money. and biggest issue the client's trust. please accept my best regards
@amizaur3marcinostrowski186
@amizaur3marcinostrowski186 3 жыл бұрын
Greetings from Poland ! :)
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special welcome
@arunkumar-bh2dp
@arunkumar-bh2dp 3 жыл бұрын
clear explanation. if we are using polarized capacitor then it will not affect the capacitor changing the direction of charging current from inductor.
@rahultist
@rahultist 3 жыл бұрын
Really Informative Video ❤️
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
it is my pleasure
@anirbansasmal4942
@anirbansasmal4942 2 жыл бұрын
Sir we have a ador mig 600 welding it's igbt burn frequently, so I cheek this machine igbt input DC series with a indutor coil and a 1ph bridge + ,- only connection with coils it's damage it may be course of igbt burn ?
@AbdulMomenZargar60
@AbdulMomenZargar60 3 жыл бұрын
Big Like For Good Work
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Big thanks dear brother
@Swenser
@Swenser Жыл бұрын
I have Induction cooker . Replaced igbt pair already. But nearby ZD diode also shorted. The diode in other side of cooker reads as normal diode perhaps IN 4148. Do u think is standard N4148 is ok to replace?
@MrsRashidSajjad
@MrsRashidSajjad 3 жыл бұрын
Ma'Sha'Allah nice information sir
@josebelmancanoy8104
@josebelmancanoy8104 Жыл бұрын
sir it is possible to double the igbt of an inverter welding so that it would not blown right away..?
@merittechshop
@merittechshop 3 жыл бұрын
Very informative, thank you. Could you please make video about zero cross sensing and such other sensing circuits in induction stove...
@gauripartapshanker9197
@gauripartapshanker9197 3 жыл бұрын
Nicely explained, thank you so much
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
You are welcome
@ARA-HOUSE
@ARA-HOUSE 3 жыл бұрын
Lk 149 brother 👏👏👏 keep it up
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Thank you so much 👍
@ivaylopetrov3277
@ivaylopetrov3277 Жыл бұрын
Hi Haseeb. My capacitor is 800V 0,25micro farad. I measured 230 nano farad. Is that problem. Also I have 4 IGBT who works on two couples for each end of the coil. One of the couple give me a short circuit if I measuring on board. If desoldering them their value are normal. This their condition is same if there is no power on the motherboard. I had short circuit damage and one IGBT was burned. Also big diode between rectifier and IGBT. What is your opinion. I ordered other three IGBT to replace them too.
@susantaatha6468
@susantaatha6468 3 жыл бұрын
Beautiful information.
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and lovely thanks
@abughoush5132
@abughoush5132 3 жыл бұрын
وعليكم السلام great people have always fantastic output
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@boybravo689
@boybravo689 3 жыл бұрын
Watching now thumbs ups done sir in your experience what brand of soldering lead do you recommend to used sir
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
there are many brands Kestre Soldering Wire 60% Tin/40% Lead with Flux Core Maiyum Solder Wire Wyctin Solder Wire Austor Solder Wire Hgmzzq Solder Wire Cardas Mudder alpha solder wire Wyctin china alphametals
@singarsaleembalchani4130
@singarsaleembalchani4130 3 жыл бұрын
ماشاءاللہ ماشاءاللہ بہت خوب*
@rolanddejesus8685
@rolanddejesus8685 11 ай бұрын
thanks very much sir for sharing...god bless.
@HaseebElectronics
@HaseebElectronics 11 ай бұрын
You are very welcome
@lakshaysharma0132
@lakshaysharma0132 2 жыл бұрын
Brother i have an induction model-prestige 16.0 , in the drive section 8050 pnp transistor was open circuit i replace it and induction worked for several days and after that again the igbt went short circuited 😢😢😥 plz help me
@rahulpatelgujratahmedabad3497
@rahulpatelgujratahmedabad3497 3 жыл бұрын
Good tiching karte hai 👌👍👌👌👌👍👌👌👌
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot
@manojp6641
@manojp6641 5 ай бұрын
Realy u r genious
@Bismillah12344
@Bismillah12344 3 жыл бұрын
Great 🌹
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Thanks for the visit
@batistafrose6009
@batistafrose6009 3 жыл бұрын
ماشاءالله You are too Good sir
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@aliranlistrikcom
@aliranlistrikcom 9 ай бұрын
very great sir.. thanks..
@HaseebElectronics
@HaseebElectronics 9 ай бұрын
Most welcome
@adolfdias8997
@adolfdias8997 Жыл бұрын
Dear Haseeb. My treadmill 's IGBT keeps burning within few seconds 😢. Could you please explain why?
@Versatiledani
@Versatiledani 3 жыл бұрын
Great sharing
@aviandragon1390
@aviandragon1390 Жыл бұрын
When choosing a replacement IGBT, don't forget to check whether or not the component you are replacing and your replacement component have an internal flyback diode! Most modern devices contain this, but not all. Always check your datasheets. Don't assume that adding one where there was not one before is a good idea. Generally it is best to use the exact same part the manufacturer used whenever possible.
@farouqhannibal1916
@farouqhannibal1916 3 жыл бұрын
aslaam brother, sukraan for the indepth teaching of Why IGBT keeps on popping, am working on a cooktek induction single hob, fuse keep on popping when I replace it and it has 4 inline IGBT 's, and I was thinking before I put in the new ones, reasoning to myself why and your video just made it clear the reason why it keeps on burning out because of the coil or maybe something els, can you give another explanation on it kanalah.
@AbdulMomenZargar60
@AbdulMomenZargar60 3 жыл бұрын
Walikum Salaam Bhai Sahib
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
shukriya bhai JI
@aliali-et7xh
@aliali-et7xh 2 жыл бұрын
Assalamualaikum.. Good video sir... Can you explain/tutorials how 7 digit led number working n ic it use.
@FancyBangles
@FancyBangles 3 жыл бұрын
MashAllah bhai
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot bhai
@sheekbikdiy1993
@sheekbikdiy1993 3 жыл бұрын
good job
@kahlid-ataya
@kahlid-ataya 3 жыл бұрын
الله يبارك فيك اخي العزيز
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks dear brother
@MargieAndaya
@MargieAndaya 3 жыл бұрын
Watching here
@rizwanarajaukvlogs3090
@rizwanarajaukvlogs3090 3 жыл бұрын
Great information thank you for sharing
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Very welcome
@SaeedSameer
@SaeedSameer 3 жыл бұрын
Wow informative video
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Thanks a lot
@farheenfairy
@farheenfairy 3 жыл бұрын
Masha Allah great information
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot
@ummoibrahimhassan4616
@ummoibrahimhassan4616 3 жыл бұрын
Good work sir
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards dear sister stay blessed
@toqeershah6481
@toqeershah6481 2 жыл бұрын
Bai me welding machine me igbt lagata hoon to forn patakha marti he jab k transformer ki jaga output me bulb lagao to thek operat hoti he bilkul thek on of hoti he through dri circuit .lekin jese hi output transformer wali wire conect kre to on krte hi jal jati he.kia transformer to kharab ni jab k transformer k bad rectifier diod module b thek he.plz help n ap igbt se age output tak video bnae.
@singampartha
@singampartha Жыл бұрын
excellent
@HaseebElectronics
@HaseebElectronics Жыл бұрын
Many many thanks
@goutammukerjee6229
@goutammukerjee6229 3 жыл бұрын
Very keenly explanation You try to explain, is very much helpful to me , but in our repairing table please teaching us the pin point tips for quick rectify the equipment ,kindly help me for the substitute for IGBT RJH 60F7, Which is currently not available in local stores, thanks for sharing the great technical teaching,
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
FGA6065ADF IXGQ50N60 TIG110GMH
@goutammukerjee6229
@goutammukerjee6229 3 жыл бұрын
Thanks Sir for Your quick response 👍, Stay blessed
@apnashafqatbhai4908
@apnashafqatbhai4908 3 жыл бұрын
Zabardas video
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@tapanbiswas8648
@tapanbiswas8648 3 жыл бұрын
can u please upload vedio on 220 vdc battery charger scr control ckt
@zenelectronicsMD
@zenelectronicsMD 3 жыл бұрын
Thank you sir,
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@hemashri
@hemashri 2 жыл бұрын
I have this problem on a barand new Induction cooker for the last 6 months still NOT rectified. I wish to contact you on WA or email if possible. Thanks.
@clems6989
@clems6989 2 жыл бұрын
Gotta hate when that happens . Lol Thanks for video !
@JanviBlogs86
@JanviBlogs86 3 жыл бұрын
49 lk dear💕💕💕 beautiful share Bhai aap nhi ate hi Bhai
@AliyasKitchenRecipes
@AliyasKitchenRecipes 3 жыл бұрын
Ma sha allah
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot stay blessed
@cellphonerepairing2111
@cellphonerepairing2111 3 жыл бұрын
Nice
@maliksiyal7357
@maliksiyal7357 3 жыл бұрын
valekum salam elder brother how are you
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot dear brother
@Abubakar-op1uj
@Abubakar-op1uj 3 жыл бұрын
MasaAllah. Jajakallah.
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
thanks a lot dear
@hasn812
@hasn812 3 жыл бұрын
اللهم صل على سيدنا محمد
@WazaifEkamil
@WazaifEkamil 3 жыл бұрын
Jazikela for sporting 🙏😭
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
best regards and special thanks
@desimomvloggerspain1454
@desimomvloggerspain1454 3 жыл бұрын
MASHALLA 🌹
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
Jazaak Allah khair
@ehsanuddin7706
@ehsanuddin7706 3 жыл бұрын
Bosss short vedio bnaen
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
i will try my best, but it is impossible to explain clearly in short videos but i will try my best please accept my best regards
@ehsanuddin7706
@ehsanuddin7706 3 жыл бұрын
@@HaseebElectronics my concern is that reason for igbt blown out is same as fuse example current rating or voltage
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
@@ehsanuddin7706 the biggest headache is fake marking numbers may that is not that igbt but it it named by fake marking sometimes quality failed components are supplied always try to purchase from some reliable source
@ghulamhussainmagsi2301
@ghulamhussainmagsi2301 3 жыл бұрын
Sir make this video in urdo.
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
کل ان شاءاللہ حسیب الیکٹرونکس اردو چینل ہر ملے گی
@dantronics1682
@dantronics1682 3 жыл бұрын
snubber circuits need replacing
@HaseebElectronics
@HaseebElectronics 3 жыл бұрын
in resonant circuit, most of time there is not snubber circuit. because in induction cooker the resonant technique is used snubber is in fluback topology
@reynaldodempo7809
@reynaldodempo7809 Жыл бұрын
I have the same problem.
@homamalsrour5673
@homamalsrour5673 2 жыл бұрын
جميل watsapp
@HaseebElectronics
@HaseebElectronics 2 жыл бұрын
thanks a lot
@LUCKY007725
@LUCKY007725 2 жыл бұрын
Asalam alaikum, Very nice, could you please explain the driving circuit of IGBT with circuit diagram....or share me the video inwhich you already done this... Regards
@suvamelectronics1329
@suvamelectronics1329 9 ай бұрын
Vge parameter
How Strong Is Tape?
00:24
Stokes Twins
Рет қаралды 96 МЛН
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН
The Best Band 😅 #toshleh #viralshort
00:11
Toshleh
Рет қаралды 22 МЛН
[436] How To Test IGBT / How to Check IGBT with Mulimeter / Why IGBT Damage
15:39
{881} Induction Cooker Fuse Keeps Blowing
15:10
Haseeb Electronics
Рет қаралды 33 М.
{1254A} SMD capacitor short circuit detection tricks, Q&A
14:19
Haseeb Electronics
Рет қаралды 4,8 М.
#299 Single Board Inverter IGBT Welder Machine - Function & Troubleshooting
32:33
{683} How To Power Up A Circuit For Repair || Work Bench Safeties
15:23
Haseeb Electronics
Рет қаралды 55 М.
{223} How to Design SMPS Switch Mode Power Supply
27:09
Haseeb Electronics
Рет қаралды 355 М.
Resolver working principle
3:09
3D ANIMATION TECHNOLOGY VIDEO
Рет қаралды 6 М.
How Strong Is Tape?
00:24
Stokes Twins
Рет қаралды 96 МЛН