6KW | 350V to 220V solar inverter

Only $2 for 5pcs 2 Layer & 4Layer PCBs: jlcpcb.com/cyt
Use promotion code "JLCATH" to get extra $2
You can buy all components for the project here:
utsource.net?source=KZbin
This is a commercial project of mine, It converts 350V of solar cell to 220V. Maximum power 6KW with 8 IGBT 70A
Download the project on my 2nd channel: • Mạch cầu H 6KW cho năn...
👉 RD6018W : bit.ly/3oMozQe
👉 Spring Sale : bit.ly/3bZ8NOM
👉 Tools & Electronics - bit.ly/3cIJPlZ
👉 My shopee : shorten.asia/Z...
If you like my video, give me a cup coffee. Thank you very much.
Donate : www.paypal.com...
Facebook group : bit.ly/Creative...
Contact: [e-mail]
Phone: [phone]
#Inverter
#Solar
#12Vto220V

[@PhdHung]

👉 RD6018W : bit.ly/3oMozQe 👉 Spring Sale : bit.ly/3bZ8NOM 👉 Tools & Electronics - bit.ly/3cIJPlZ 👉 My shopee : shorten.asia/ZBD3pQUs

[@thelydiaspringexperiment6437]

a couple of questions: why use many small igbt instead of 2 large igbt modules? would your circuit drive MG06400D-BN4MM instead? also do you have an international store online? i would like to take a couple of boards but ship to europe

[@yasirnawazshahani4870]

I want to buy this how much price is this

[@technicaldiy]

*You should add a lighting device from the camera side for studio system. The video will light up*

[@electron7373]

Add a heatsink and give us a demo with progressively higher loads: 1kw, 2k, 3k,etc. Or at least run it with an electric kettle.

[@ngocdangdinh9874]

For wide range of MPPT DC input, this board need both buck and boost converter!

[@Dc_tech386]

To be honest the irf2110 driver on the spwm module is not enough to drive all those igbt to it fully capable only half so drawing 6kw will blow the igbt because the ig t will go into saturation from lack of enough gate current to fully open the drain because each igbt need its own driver like optocoupler driver ic

[@klsonidhanla]

Nice brother 👍👌👍 Please share the high power inductor core material and copper wire thickness and turn. Please

[@teemum.9023]

How many solar panels are needed to run a air conditioner? Appliances like fridges, freezers, and air conditioners aren't as simple, however, due to them containing motorized compressors. This means that the power they draw would vary and need to be averaged out. An air conditioner would need around 1,200 watts of solar panels for each ton of cooling capacity

[@SivaKumar-od1ox]

Appreciations for the efforts taken...

[@bisnetodeportugues]

Two-Sided Circuit Board. Very Difficult to Manipulate. but this Circuit is interesting. Greetings from Brazil. 🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷

[@amirebrahimieftekhari6876]

awesome👌. what is the thickness of output inductor copper wire ? and what type of core

[@noorhabib3855]

You should test it with heavy out put not just 100 watt bulb itleast more than 2000watt

[@khurramshahzad2899]

Where is the you add 60 >400v to 12vdc modul please sheare link this mudle.

[@alexb2494]

Where can I find the circuit diagram? Where can I find the full list of parts? Can you show how this inverter works with, say, 2kVA AC unit?

[@guguslangit2230]

always nice build, ✨ btw how about DIY micro inverter for on grid system, is possible?

[@Dc_tech386]

My question is the igbt won’t turn on fully so there will be heating on bigger load won’t there be

[@gumnahs]

Wow !! Just amazing 😊👍

[@sddiymakeitworthit7512]

Nice creative

[@ArvindKumar-Physics]

Great effort... Please share its circuit diagram . Thanks

[@mahilfernando]

Nice work sooo waited for this video bro 👍

[@PhdHung]

Thanks bro

[@vengug7303]

Hello Sir .. Your videos are most useful for everyone kindly help us to make a video for output inductor calculation... like core and wire selection.... current and total watts to make exact output inductor please make a clear video better to everyone Thank You.

[@yunodiewtf]

Trying to convert old GM Volt gen 2 battery (96S Li-Ion, 120KW peak) to home ups by feeding the DC directly to the sine chopper capable of 15KVA. Any suggestions before I burn a hella lot of mosfets and potentially cause lithium fire?

[@electronic7979]

Nice project

[@shidasheran]

Great job, my friend. Can he really take out 6kw because I want to run a water plunger on him in the well?

[@peace7439]

Loved it ❤️

[@bengalmirror]

you are doing great work ever

[@Dc_tech386]

Can that inductor really handle 6kw of power or because I use bigger induction and it get on fire at 3kw load

[@bhupendratomar6797]

Bhai ise purchase kaise kren

[@argentinomacrifuevidaltamb3772]

Excelente proyecto amigo. Saludos

[@ArvindKumar-po1dy]

I want to buy this, what you say?

[@RazaSolar]

Respected Awesome Tech. Dear Sir how we can attached dismplay lcd with it? please demonstrate

[@bengalmirror]

Great work ever

[@teemum.9023]

9:35 360 volts of direct current to transform into 220 V. How many watts does that use? Would 3600 volts from 10 solar panels DC be enough for how many watts?

[@teemum.9023]

1:54 46 W for one fan. Can you please use 3000 W and show me how many panels are needed

[@creativebuilder577]

Bro, what happened to the files in Fb group. Everything was lost

[@lymmentrixprofessional]

This is awesome, thanks

[@petername2608]

Finally 🙏 great work sir 👍

[@PhdHung]

Thanks bro

[@petername2608]

@@PhdHung bro can you do full load test .max load this board can take. And for for choke what core you used and how many turns

[@josepeixoto3384]

6kw with IGBTs of 70 Amps? those were mosfets 47N60 (at 06:46) how much power with those 8 Mosfets? thanks,your videos are the best how can i buy the PCB

[@kunnup466]

nice project bro, I don't see mosfet for a 360 volt power amplifier, where is it? thanks

[@coptermangyro508]

Would anyone share the circuit diagram?

[@nitinpatel469]

Please sir make a grid tie inverter

[@malwaengineeringservices8394]

Thanks for very usesfull video, But how and where can place order for pcb and components. can you advice any specific pcb modle no.we need in India, Thanks

[@ajuwinfly8272]

I wrapped the indicator coil and inserted the capacitor corresponding to 2mH 225j 400v, but when it is attached to it, the filament lights up and the capacitor I used makes a chirping noise when there is a small pulse. what is wrong 🤔🤔🤔 ??

[@aravindadas567]

sir, it's awesome technical to provide a,c 220 volt, without battery, From DC 280 volt to A,C 220 volt directly. Without step up transformer. without battery. Sir can you give me the circuit diagram of this project & circuit. pcb layout. How you arrange the MOSFETs in this circuit? How you will switch the MOSFETs for alternating current. plz describe the H bridge system sir. watching your video from Bangladesh.

[@MyOwntuahur]

Nice work the best

[@hichamtassi1753]

Hi, wht such a big voltage drop with the hair dryer ? from 200v to 184...

[@cipry1010]

why did you replace the resistor for current feedback?and what value

[@اریاحیدری-ر6ش]

Pin 1 is for output short circuit or overload protection??

[@ShakeelAhmed-ft2mx]

Very nice bro

[@kamranahmed4602]

I wish to buy it, do you sell assembled kit? BTW nice job keep it up.

[@z0130132001]

建議應要以小矮的零件，開始安裝焊接，才會比較順😅

[@sajidmunir864]

Awesome 😎

[@mangkornseesad5450]

Very hard for parallel big mosfet/igbt but you can do it simply.

[@electrontech2044]

Good job

[@MuhammadDaudkhanTV100]

Awesome

[@nitrousman8882]

Is the 200v reading expected? I would have hoped for 220/240 at 50hz. What am I missing?

[@claudiosteeman6838]

6000w nominal o pico de 6000w y 3000w nominal?

[@tossancuyota7848]

im pretty sure this wont work to power a fridge

[@intelpeople]

its work easily

[@nitinjirawal]

It's not converting 12v to 220. It's reducing 300plus volt to 220volt

[@sinarbatuah3413]

hi, may i know where is your location pls, city? country? thanks.

[@AviatorDark]

so when you order the pcb is there an option to purchase the parts to assemble the circuit from JLC PCB?

[@petername2608]

Can you tell the no of turns for choke and what gauge u used

[@adeshinaajibola5114]

How can I use one ferrite transformer for both inverter and charging

[@rohullahnoory]

Thank you for your project and it's sharing I have a question since you added an adapter to the pcb for making 350vdc to 12vdc! Can I directly connect 12vdc to the pcb? Will it work? Will it give me 220vac?

[@thelydiaspringexperiment6437]

i think his adapter is to power the circuit, not to provide power for the output. to do what you want requires an LF inverter or a 2 stage inverter

[@niazkhattak3396]

Kidr sy mil Jaie ga ye PCB complete

[@triphetchannel]

คืออยากรู้ว่า ใช้ไฟ 380v อินเวอร์เตอร์ ถ้า เอา ไฟจากหม้อแปลง แปลงไฟ 380v ไปใช้ มันจะกินกระแสกี่แอมป์ โหลดแอร์ 12000 BTU วัดตรง DC

[@irshadalielectronics5569]

How much price of this circuit

[@agussulaiman9553]

Dimana saya bisa pesan inverter itu

[@joserolandsancheromero4440]

Una pregunta. ¿Esto transforma el voltaje del panel en un voltaje ac de 220v?

[@PhdHung]

yes. AC 220V

[@powerelectronics8568]

Overload protection?? High volt dc protection?

[@moloky7535]

En la descripcion del video dice Usar IGBT de 70A . Pero en el video se colocan 47N60 (MOSFET). No es la misma potencia de 6kw. Creo que el egs002 necesita modificar la parte de disparo para IGBTs.

[@josepeixoto3384]

qual es la diferencia? thank you

[@moloky7535]

Las tarjetas esoo2 atacan muy bien obre mosfet al llevar el Driver ir2110. Sin en bargo todas las tarjetas que Hay para atacar IGBTs .lo hacen Mediante optoaisladores tipo Tlp350.....250 etc. El paso de tension positiva a negativa en puerta es mas critica y tiene ue ser mas segura. Los IGBT trabajan mejor a tensiones altas generalmente Y los MOSFETS no son para altas tensiones . Aunque conmutan mas rapido. En el video se usan los MOSFET 47N60 2 por rama del puente H. Los 6000w que anuncia son solo de pico. Y durante unos segundoa. Como salida estable son 3000w. Para mas .hay que ir a IGBTs ya Que con mosfet a partir de esta potencia trabajan muy al limite. En general desde 3-4 kw hacia arriba hay que pensar en poner IGBTs.

[@shabirahmad7427]

Dear bro would you please tell me how to by this 6000watt wat is the price of this readymade card

[@ramanbhall1245]

I need this circuit

[@kibenqucak6429]

Aaa i was hopping that u were uploud vid about new ultra high power psu😔😔

[@PhdHung]

ok bro

[@ajuwinfly8272]

What is capasitor value ? For 2.32mH indicator ..🤔

[@Ankursachan343]

How to purchase

[@nataneilwilson7231]

Where can I get the 60v>400 to12v DC converter to buy?

[@ivjik]

Are there gerber files? Please post if you don't mind.

[@versatec1]

Could you incorporate a soft start? I want to run a chop saw (draw saw)

[@PhdHung]

Yes, it has soft start.

[@user-wo7eb6ky1g]

Is this device converts the350VoltDC to me 220VoltAC May I please give you an electronic circuit? and elements and worth

[@vidyasagar2602]

How to get this kit and it's price

[@berlicoenfarel8184]

Can you make pocket 500watt inverter

[@ajeetsingh941]

How to buy parts? Please help.. thank you

[@Afzal_Nafees]

اسلاموعلیکم۔۔۔پلیز بھائی استری لگا کر دکھائیں۔۔۔

[@akramkhan7908]

Sir koi aisa converter bnao jo dc400 volt ki dc 48 ya 24 volt bna de

[@yasirnawazshahani4870]

I want to buy this how much price is this

[@TheJavaSync]

Is it safe to connect high voltage PV to inverter directly (without battery) ? When the load increasing - what will be happen?

[@PhdHung]

If the load is larger than the solar panel, the output voltage will drop

[@TheJavaSync]

@@PhdHung thanks

[@ahmadinfo3960]

Price of kit

[@kamilshahsyedjeelani9432]

Please brother help I have to use DC600v to 220VAC what changes are needed?

[@ajuwinfly8272]

Hello wht is 60>400v to 12vDC module 🤔 ?

[@shivjigupta8807]

Sir one pis kitane ka padega

[@ZameendarAhmed]

Sir aap ye pcb sale bhi karte ho

[@user-pv3ns4vt6i]

Good job brother… 👍 Please can you share me h-bridge converter to convert 350v DC to 230v AC without using EGS002 .🌹

[@thelydiaspringexperiment6437]

egs002 is the cheapest best way. also very easy to buy online.

[@nammon7380]

อยากได้ Lay out pcb จังครับอาจารย์

[@jbworksdiy]

can you make a 10kilawatts inverter sir thanks and godbless

[@BRIGHTPOINT14]

its 6 KW, so please run at least 2 Ton AC

[@shadmehraria5473]

What type is the coil?

[@ienTuDIY]

anh ơi đầu ra e lọc chưa kĩ hay sao mà tần số nó nhảy lung tung từ 50-150hz vậy thì dùng các thiết bị điện tử có sao không anh

[@PhdHung]

có đó, sóng sine nó có nhiều gai-hài. đương nhiên không tốt rồi

[@ienTuDIY]

@@PhdHung anh cho e xin link video làm mạch đo cuộn cảm bằng arduino dc ko a, e tìm trên kênh anh mãi mà không thấy

[@adeshinaajibola5114]

How can replace egs002 card using atmega328

[@denchesnuk8470]

Здравствуйте а схема будит благодарю

[@solarpump3540]

Not working properly short MOSFET and Egs002 module

[@jbcnc74]

Hallo, wo kann ich fertig augebaute inverter kaufen? Danke