{842} Single Switch "Forward-Converter" Topology

[@electroniquepassion]

it is interesting to know. It is well explained. 👍👏👋

[@HaseebElectronics]

thanks a lot for your valuable appreciation please accept my best regards

[@vijayakarekar]

You are my univercity....thanks a lot sir ji....

[@HaseebElectronics]

It's my pleasure

[@ABDERRAHMANE-y4g]

Sallam ALIKOUM ! On apprend beaucoup avec vous! Encore merci !d'ALGERIE

[@ionix2000]

I am happy that you explained the difference between flyback converter and forward converter. Very important that in forward converter the current in the coil is higher compared with flyback. Thank you again for everything. 👍👏👋

[@HaseebElectronics]

best regards and special thanks

[@waldeniya]

Very simplified explanation,excellent teaching ability…..thanks

[@kmhovlog6185]

Like very interesting amazing wonderful informative video good job thanks 🙏 for sharing

[@HaseebElectronics]

beset regards

[@Dc_tech386]

Very well informative I learn why my converter was blowing diodes and igbt and mosfets now I use 114 volt with a 600 volt rating igbt and 200 volt rating mosfet and 200 volt Shockley diodes so thank you very much for the information

[@LousyPainter]

Excellent! I don't know a better word to describe this video. Thanks.

[@HaseebElectronics]

best regards and special thanks

[@cristiansantos5742]

You are a good teacher !! Thank you, sir.

[@HaseebElectronics]

You are welcome!

[@shefqetkaralliu6816]

Ottimo spiegazione. 🤩🙏👍

[@MarkPrince1317]

Thank you very much brother a very clear and simple to understand thank you request for next level push pull topology Best regards from Philippines 🇵🇭

[@jesuschuerta6434]

thank you for diagram and explanation.

[@HaseebElectronics]

it is my pleasure

[@wesameed824]

Thank you for good explanation I hope to see practical experiment

[@janahmed4190]

good information thanks sir

[@HaseebElectronics]

best regards

[@sarangajayanetti1569]

Dear Mr. Haseeb. I am from Sri lanka.I respect and gratitude for you, because you have done very valuable and superb tremendous service to the electronic field.Your endeavor is very very successful.I also have attempted to design boost converters, but i was unable to get regulated output voltage. In (no-load) condition, it was success. But it couldn't drive the load.(output voltage became zero level when load is connected).I hope your further clarification about this matter and calculations and design explanation about boost-converters in future videos. Thank You.

[@jaym5938]

Excellent as always! Thank you! A quick question: when switch is on and there is positive voltage on the cathode of the capacitor, does that not damage the capacitor?

[@nazakathussain4871]

Excellent

[@HaseebElectronics]

Thank you so much 😀

[@rmjnm]

Great!

[@ministeriomundialliberando8403]

Thank you and very well explained though in reality it is pretty much complicated.

[@HaseebElectronics]

best regards and special thanks

[@peterfrancis3865]

Thanx nice 👍

[@HaseebElectronics]

Most welcome

[@anlpereira]

Hi. I have watched a lot o video from to try to understand how to winding smps transformer. Can you make a video showing how to winding the flyback and forward converter? Thank you very much.

[@rodsbons4412]

sir i have a question?why is it when u measure amps. of the unit goes up when plug in small voltage than higher voltage.for ex. led tv wjen plug in in 110v is higher current than u plug in 220v.how is that happen?when ohms law said that voltage is directly proportional to amps.hope e make a video for it.

[@علیسعدابادی-ص8غ]

great

[@HaseebElectronics]

it is my pleasure

[@tvbox8478]

👌 👍 ✋

[@HaseebElectronics]

best regards

[@HadiiKarami]

how to Design transformator forward topologi?

[@nayanjagirdar8408]

👌👌👌👍

[@Ibanez25145]

are you from India?

[@HaseebElectronics]

no I am from Pakistan

[@quanghoang04]

👍👍

[@HaseebElectronics]

best regards

[@idushandilitha9181]

Sir we want Gate Driver Transformer explain and how to winding Gate driver transformer ?

[@miloradgraovac74]

Brother,all you have posted so far is for10 please your trnslation in SERBIAN.