88-97 Nissan D21 Rear Brake Shoes replacement

Rear Brake Shoes replacement have fun!
All parts are from Napa
www.napaonline...
Harbor Freight Drum Brake Spring remove tool
www.harborfrei...

[@danierukame]

🤙 hell yeah helped out a lot

[@sharkkattack3741]

Ignore all the negative comments...this video really helped me out with changing my brakes and as long your videos can help someone that's all that matters!! Thank you!!

[@boonrichter3044]

On the bright side all your clip troubles gave us a pretty efficient method of removing it in minimal time! Thank you very much for such a clear demonstration!

[@curtfox91]

I literally have PTSD from that clip lol 🤦‍♂️

[@patsmith5236]

Wanted to say thank you.Just did my rears and didn't like the way the ebrake felt. I looked again and realized I put that little spring for it on wrong. Your video is the only place to confirm my suspicions. Thanks again.

[@S1L3NT.STJOHN]

Your video helped me get mine done... it was simple and thank you for the knowledge homie.....couldn't have done it without ya.....keep it up.....D21 for life

[@Mollozzz]

Clip took me two mins to take off and change but this help a lot

[@andrewnorgrove6487]

Done hundreds if not a thousand brakes relines over the decades ! Its a learning process bit like muscle memory My first likely took hours no doubt But over time it gets quicker and easier But the best thing is to keep your cool ! always walking away for a rest when thigs don't line up , good video Sir 🤟🦘🦘

[@wordisbond7603]

Appreciate all your content!👌

[@curtfox91]

Thank you Enjoy your Hardbody 👌

[@streetskater521]

Knock a pocket flathead between the two ends of the clip then take a larger screwdriver place it on the end and you can hammer it out in one go

[@curtfox91]

To late for that i got it out ha ha

[@streetskater521]

@@curtfox91 just a easier way

[@itz_brax1069]

Like the truck thanks for the help

[@jogmas12]

Nice crocs

[@weekendhomeprojects]

@3:37 - Ole boy rolled up on you all moist. Gotta keep one eye on the streets at all time.

[@raymondnecke5806]

Whenever I do my brakes , I place a container underneath and spray everything down with brake cleaner then come back later so there’s minimal crap covering everything

[@landenemilio8064]

you probably dont give a shit but if you're stoned like me atm then you can watch pretty much all of the new movies and series on instaflixxer. I've been streaming with my gf lately :)

[@pauldawson5418]

@Landen Emilio Definitely, have been watching on InstaFlixxer for months myself :D

[@brendonphillips8085]

Thank you

[@1o1carolina53]

" Disc Brake Quiet forms a water resistant, high-temperature film that absorbs noise while quieting squeaks & squeals. Specially formulated to dampen the vibrations that cause brake noise. For use on the back of non-shimmed disc pads."

[@curtfox91]

Wow you deleted the other comment you left. And like i Said my Brakes are still Fine to this Day 🙌

[@1o1carolina53]

@@curtfox91 of course I did You're a hack

[@amoore-zd9zv]

You should be able to put all your springs on with the brake spring tool. However, Your method worked. You should clean and lubricate that self adjuster. Most of them don't work because they're full of crud. I hope you put the cap back on that wheel cylinder. Constructive criticism aside it was a good video.

[@curtfox91]

Lol I put everything Back as needed Brakes are still good and strong since this video was made.

[@nicolasortiz1509]

how tf do u get the c clip on its so hard i hate it

[@andrewnorgrove6487]

Toss the special tool away 👍 get a snub nose plyers placing them over centre pin not clamping But just compress the round spring , once compressed rotate plyers until slot lines up then Release ! 5 seconds per side this way

[@curtfox91]

Already got it on

[@loucifer323]

Always take a picture before I remove anything so I remember how to put it back

[@curtfox91]

What are you referring to in this video? The little C Clip?

[@bartswoodshop7212]

There is an easy tool to remove that clip

[@1o1carolina53]

That product will dry semi hard. You just f__cked YOUR brakes. They'll not open and close correctly

[@1o1carolina53]

Read directions!!! " Disc brake quiet " ISN'T lubricant is a product that dries on back of disc pads to create soft surface to PREVENT rattle WHEN hardware fatigues. Dude!

[@curtfox91]

My Brakes dont make any Noise. Im Happy 🤘

[@jamesfield6568]

Don't do how to videos if you don't know how.

[@curtfox91]

This Comment Is Trash. Don’t tolerate idiots like yourself.

[@brandonk1502]

If you don't like his video then you don't need to watch it. You certainly don't need to comment on it and be negative about it.

[@biker58hd]

Amateur brake job!

[@curtfox91]

Who is a pro around here? It aint me.

[@timmarshall885]

If you don't know what you're doing, don't make a how to video on something

[@curtfox91]

Shut up already with these Comments. All your going to do is get blocked cause your a Bot or something clearly.

[@brandonk1502]

If you don't like the video go make your own then or just be quiet. It may not be exactly the way I would do everything but at least it's helpful.