90 Degrees - Different ways to weld square tubing

Today, a short video where you can see how to connect steel square pipes in various interesting ways.
To calculate other sizes of joins, you need to do a calculation. For example, square tube with 70mm sidewall.
70mm - 2mm (one wall thickness) = 68mm
On the website for calculating formulas, we are looking for a formula to check the circumference of a circle.
Where "r" we enter 68mm, which will give us a circle circumference of 427mm.
427/4 = approx 107 mm
107mm + 2mm (wall thickness) = 109mm.
Thanks to this, we know that the length of the side cut will be 109 mm.
Lastest video
Kinetic Log Splitter - Build - • Kinetic Log Splitter -...
Making The Hydraulic VISE DIY [Plans] - • Super Strong Hydraulic...

[@nordishkiel5985]

Cool trick! The round edge is a lot of work to cut, but the double V is nice and quick and looks so much better than a simple 90°. Neat!

[@steptowdaughters2633]

Exellent video,especially for the novice to grasp the idea of how to do this.i like to leave my beads showing if it doesn't have to be for looks.Cheers.

[@Reman1975]

I've had to make radiused corners on box section projects a couple of times, and I found it a lot less hassle to use steel the same gauge as the tubes wall thickness, then turn it up discs of to the desired diameter, and chop them into 1/4's and weld those in as corner pieces between pipes cut to 90', before capping the outer radius with some rolled steel strips. As an exercise in accurately marking out, cutting and welding, doing the curve from one piece is fun personal challenge, but if you need to accurately get 4 of them perfectly placed on each of 10 lengths of tube to make 10 shelf frames that are all perfectly square, visually identical, and looked mass produced, I'd say making the corners separately and welding them on is the way to go. :D

[@kameljoe21]

That is cool. One could use a jig. Depending on where you live box steel is pretty much all standard sizes. A person could make half a dozen jigs and then use either a torch or plasma cutter to cut out the section. The jig could clamp on and off set based on you plasma cutter off set and then you could cut them out fast. This would also allow someone to make a square with a whole piece as well. Though your idea is pretty awesome as well!

[@boratsagdijew2385]

W końcu jakiś filmik na poziomie a nie te pseudowynalazki.Brawo

[@SekAustria]

This trick is better than bended tubing. Nice video bro!

[@MadeinPolandChannel]

Thanks man! :)

[@thisoldjeepcj5]

Glad to see you use the safety guard on the grinder!

[@user-xh5kx4mi1h]

Молодец, пан. Достоин подражания в аккуратности и продуманности.

[@assassinlexx1993]

And that is how you make Polish boomerangs😉😄 List of clever engineering for square bends.

[@MrOner07]

simple tutorial videos like this really spices up your channel once in a while...great job!

[@ahamedkhan232]

Just learned some awesome stuff. Definitely going to be using this. Thank you!

[@silvergrizzly316]

I just don't know why but this is so satisfying to watch. Awesome my friend!!! 👍👍

[@zbudujsamdom]

Elegancko 💪

[@DreamerDrafter]

Great idea to making 90° tubing for welding. With complette formula in the description column. Thank you for this useful video. Good and precision result. Regards ✔👍🙏👌

[@wswsws77]

Oglądam Twoje filmy od dawna,ale nigdy nie komentowałem,jesteś przekozak.

[@nukecoladrinker7744]

no i doczekałem się nowego filmu , i jak zwykle łapa w górę:)

[@alihameed6672]

We are familiarization to watch a different ideas in all your videos, but now I think it's old idea! Anyway keep going, we do love ur job 💙

[@joshbrucksch]

Oooh - very useful, thanks!

[@MattysWorkshop]

Gday, Congratulations on hitting 1 million subs, awesome job mate, Cheers

[@luiscarlossuarezmarquez264]

I like the idea to build some clamps. Thanks

[@wolfparty4234]

Nice work guys!!!💪🏼🔥🔥🔥👍🏻

[@rasmis]

Brilliant idea.

[@1leggeddog]

Very cool I'm saving this video for the future

[@MCsCreations]

Awesome tricks, dude! 😃 Thanks a lot for the tips! Stay safe there with your family! 🖖😊

[@MaBuKunsthandwerk]

Tolle Ideen Vierkantrohre zu "biegen" Danke fürs zeigen

[@temyraverdana6421]

Wonderful, thanks a lot

[@user-wj1po1ut4n]

Как всегда классно!Супер мастер!

[@jean-michelcoutable4998]

A ce niveau c'est de l'art!

[@Radkosky]

Uwielbiam dźwięk spawania 😄

[@user-pk5ex4dn4x]

Хорошая работа! Удачи тебе!!!

[@Piotr_T]

Jak to miło widzieć kogoś takiego jak ja i ma w d BHP używając tarcze do cięcia do szlifowania. Aż się łezka w oku kręci :)

[@alvarobotelhovillelaaprendernu]

Show parabéns 👏

[@mr.ranyhomemade2466]

I'm happy with your diy

[@samhawkins3847]

Perfektní video jako vždy Děkuji Ať se daří :-)

[@sddiymakeitworthit7512]

Nice job 👍

[@arekprzybyszewski4814]

Dobra robota 👍

[@DIY-py5fb]

Good job

[@MrAJWorks]

Great 👌 As always helpful tips👍

[@ALI-fj1xf]

All what you do is amazing !!! I subscribed to your channel since long time and i appreciate if you make a video on how to make a hydraulic rebar bender for construction works !

[@rhalphaugusto]

USEFUL!!

[@adelinopietropoli4978]

Wow congratulations good job 😊👍👏

[@mazika5337]

Love the vids

[@user-sm7uh3mr9e]

Миллион, поздравляю!!))

[@shailendramore692]

Genius 🙏🏼

[@zareenremendies]

👍👍👍Exellent video

[@GxsieteRaySimRacerGTX]

Great 👌

[@Dewajtis1944]

Rewelacja !

[@Treylopez1997]

I have watched many videos on how to do this and they are all super confusing using math but the way you showed is so simple thank you

[@zumbazumba1]

Math hard -math make brain hurt baaaaad!

[@Treylopez1997]

@@zumbazumba1 it was the way they explained the math not the math itself

[@hamdiscreativity7906]

Hello made in Poland ,how are you, I'm obsessed with everything you do

[@8.gauge.shotgun]

nice!

[@hannyhanny7324]

Loking good man

[@alfredneumann4692]

Super!

[@marekroszkiewicz3524]

Jak to miło popatrzeć będąc w pracy jak pracują inni😁

[@MadeinPolandChannel]

Coś w tym jest 😁

[@TECHNICUSChannel]

Siemanko patrzę i zostawiam wszystko co trzeba i pełne wsparcie, fajnego dnia! Kolega TECHNICUS 🤖

[@Gmanboobies]

Awesome from Greenpoint Bklyn

[@BLacknesmonstaz]

Awesome man! I really like it I subbed immediately. Now try with no music :)

[@marcin3688]

Super sprawa jest

[@NiclasutanK]

Hey. Thanks for all of your videos. Today i been working with 40x40x2, and I followed the progress. 40mm pipes = 63,5 mm didn't work! (30sec in the video) That lead to a gap of approx 5mm when bent in 90° what did I wrong? I did lay the cut on the correct side of the line. /Niclas 🇸🇪

[@fredsover2775]

Сначала лайк потом смотрим. Привет Оз Беларуси

[@SenTirTv07]

Good 👍... salam satu hobi dari Lereng Gunung Slamet saudaraku

[@zumbazumba1]

Ok i understand everything until 4:37 - when you mark those 2 triangles that are spaced from each other -is there any rule how far they can be or is it whatever you want ?

👍👍perfect

[@seanalvarez9588]

Лайк в поддержку канала. Удачи тебе ✌️👍

[@bokalfishing]

very nice charring this video,like and watching here my friend, thanks for sharing this beautiful vedio,I am a machinist also,thanks

[@ursus7348]

Jak z fabryki 👍🏻

[@Rrsport19]

No to teraz łagodny luk wewnątrz 😝

[@garybrown9719]

To calculate length of 1/4 circumference .5 × width × 3.14 =

[@Only4youV]

Do you have some good book for "life hacks/tricks" on wedding?

[@UZB_TEXNO_GROUP]

Ок очен приатно ведет ваш работ.

[@xanitoxanito193]

Si no quieres esquina está bien, aunque me parece mucho más sencillo cortar a 45 grados y soldar.

[@krzysztofb3025]

Czy jest jakiś specjalny projekt z okazji przekroczenia 1 miliona subskrypcji?😉 Gratulacje przy okazji!!!

[@MadeinPolandChannel]

coś się szykuje :)

[@zumbazumba1]

Will there be a 45° and a custom angle version too?

[@user-yn9dz3wy6j]

Ты опоздал с этими лайфхаками, их год назад кто только не показывал, только ленивый блогер не делал .

[@viorsa8200]

Excelentes proyectos muy bien desarrollados y mejor ejecutados , gracias por compartir sus conocimientos y experiencias , un saludo cordial y por supuesto un gran like desde Narón , Galicia ( España ) 🤓 😜

[@kameljoe21]

If one was doing this a lot. I would make a jig for the each size that you might use. This way you could use a torch to cut it out or even a plasma cutter. Now for those people who have a CNC plasma cutter a simple jig made for your table and some set up would work wonders for this as well. You would only need to make 2 small cuts.

[@kameljoe21]

Using the band saw is an awesome idea as well. The other thing one might be able to use is a jig saw provided you have the longer blades.

[@jacekejsmont]

Wg mnie to przerost formy nad treścią. Raczej jako ciekawostka. No chyba że komuś pasuje do koncepcji. Pozdrawiam

[@toto_93]

Could you link the grip pliers please?

[@_MadFox]

Один я там среди чирков маркером "х.. " увидел?

[@czowiekwmasce2986]

Jakich używasz gwitowników i narzynek (firma)

[@Maetti1286]

at 0:10 what tool is that and how did you make it?

[@jwg19444]

👍

[@09FLTRMM77]

MM77 👍🏼👍🏼 Approved

[@arturlend2297]

👍😎

[@EVERYDAYLAWNCARE]

Sir, I would love to come over and work with you

[@vse-prosto23]

не надо нам лапшу вешать, что прям с первого раза получилось, лучше бы показал сколько до этого метала ухандохал...

[@kamilkamil3139]

Z serii 5 minutowe sztuczki 😜😁

[@LasWay1]

😎😎

[@filfil9902]

What are you spraying On parts before welding?

[@martinw.minten475]

Antispatter spray. So the spatter and sparks don't stick to the workpiece

[@milad1stt]

👑👍

[@PauloMonti]

Show ! :) \o/

[@carman3163]

Опоздал примерно на год

[@Mr.Noobody.]

O co chodzi z robieniem tych rogów profili, to jakiś viral czy co. Widziałem to samo za kilkudziesięciu innych kanałach. Nie wiem co to jest modne czy az tak trudne do ogarnięcia.

[@Trailseeker13]

But can you do that with pipe?

[@hubertkolenderski1022]

Mogłeś wyszlifować profil przed trasowaniem z korozji.

[@pasha5584]

Хорошие бумеранги, но тяжеловатые :)

[@skun80]

Nice but so much weld dispenses

[@GuglGavno]

На Дзене таких роликов навалом

[@christophedelepaut6398]

👍👍🇧🇪

[@Waterpass.]

Один подал тему... И понеслось......

[@AlexBeljo]

бусурмане на границе а он уголки варит)

[@Dima79243]

А 45°?)