This video details troubleshooting a no start symptom. I lost power at 5500 rpms, "oh no" watch for the fix!
Пікірлер: 30
@christopherkast80453 жыл бұрын
Great video on this issue and fortunately have not had this problem on my 87 N/A. Just one thing about reinstalling the sensor bracket, How did you adjust so the TDC sensor had the proper spacing above the flywheel ?
@curtisr573 жыл бұрын
Thank you so much for posting this video! While there's no shortage of instructions online for replacing the sensors, this is the only bracket exchange help I've found. And, now it's off to the passenger side of the car to get at those 6mm bolts! Who knew?! I certainly never thought to try that. +1
@fcimports98233 жыл бұрын
Thanks man! No problem at all. You got it bro, a little patience and you'll be back rolling in no time!
@artmchugh56442 жыл бұрын
@@fcimports9823 hey man!! If you liked my comment, you may like our car !!!😂😂😂😀😀🍺🍺 kzbin.info/www/bejne/nnSrhYt5gKyZbbc
@pkvn94410 күн бұрын
is this a later car? i’ve heard in the later cars you have to literally break the bracket in order to get it out. i’m suffering the same fate as you and i would really like to just remove the bracket but if i can’t i’d rather keep the bracket in place and not lose the gap. thanks man!
@fcimports98239 күн бұрын
@@pkvn944 yep it's a late car
@samamahm61233 жыл бұрын
Hey man thanks for the helpful video! Where have you been? Been watching ya for years.
@artmchugh56442 жыл бұрын
you can get some more room to operate just by removing your oil fill cap 😊😊😊😊😊😊😊another thing to tighten or remove the bracket bolts ,get a very short 6mm Allen SOCKET and 1/4 inch ratchet!!!
@TE2REI Жыл бұрын
You doesn't mention the distance between the sensor and the wheel after removing or installing the sensor gasket ;-)
@eriktml5 жыл бұрын
no way! im driving my w211 rn because my 944 wont start haha. great minds think alike lol
@fcimports98235 жыл бұрын
Lololololol. That's awesome!
@slow9445 Жыл бұрын
lots of people gap the sensors is it really that important?
@devorahacts6 жыл бұрын
Sorry, you kept saying in the beginning, "this coil". Which coil? And where did you take the Reference sensors out from? Ar they near the front? Thanks.
@fcimports98236 жыл бұрын
devorahacts the coil is the ignition coil located at the front of the engine near the manual override for the headlights. It sends electricity to the distributor that goes to each spark plug. The reference sensors are located toward the firewall at the back of the engine. They tell the ECU (brain) that the starter is turning the engine so provide electricity to the ignition coil. If you look through my videos I have a whiteboard animation explaining the process. Thanks!
@timcomeau4204 жыл бұрын
@@fcimports9823 The reference sensor doesn't tell the DME anything about the starter. It tells the DME where the crank is at so it can fire the coil at the right time. The coil already has electricity to it. The signal is to GROUND the coil so it fires to the distributor rotor.
@shaquandavis18847 жыл бұрын
Great video! I'm going to try removing my reference sensors and checking for dents
@fcimports98237 жыл бұрын
Yeah man, you can always check first. Just remember on the re-install to make sure you have the proper clearance. I'd just mark it because there is a little play in the screw holes
@timcomeau4204 жыл бұрын
There's only 1 reference sensor, the second is the SPEED sensor.
@corymoll95724 жыл бұрын
did you say this broke at 5700rpm???? crazy high revs...I get worried pushing 1984 944 above 45000rpm
@liamflynn69292 жыл бұрын
You don't even reach the powerband
@edwinlopez18965 жыл бұрын
What is it if mine doesn't start but starts when you push it and dump the clutch I turn the key over but makes only one loud click
@timcomeau4204 жыл бұрын
Could be your starter, your cables to the starter, or your ground wires. The fact that you hear a clicking sound tells me your ignition switch is prob ok.
@marcolopez81106 жыл бұрын
Were you buy those sensors
@77magnuss5 жыл бұрын
You can get them at Pelican Parts, 944 online, Paragon Products...
@marcolopez81106 жыл бұрын
Tanks I try tomorrow I hope estar
@frederickontour14786 жыл бұрын
This is great! thank you!
@fcimports98236 жыл бұрын
Frederick OnTour no problem glad to help
@alansimmons40717 жыл бұрын
Great video, what about the spacing of the sensors when you put them in. The gap spacing to the gears on the flywheel, did you have to measure that or did you just put them in
@lizard9447 жыл бұрын
Yeah, they should be spaced or you run the risk of them being chewed up by the flywheel cogs or misfiring if the gap is too wide. The manual says to take an old sensor and glue a 0.8mm washer to the bottom of the sensor to act as a feeler gauge to set the gap. You can use your new sensor as the gap tool but you'll want to use an easily removable glue so as to not damage the sensor end.The washer should be a little smaller than the diameter of the sensor so it will fit through the bracket hole. Bolt the bracket on loosely with the homemade gap tool installed on it then press it downward till the sensor (washer) contacts the flywheel then tighten down the bracket bolts. Then unbolt and remove the washered sensor gap tool and replace it with the new sensor. This should produce a sensor gap of 0.8mm from the flywheel .
@timcomeau4204 жыл бұрын
Lizard 944 has the gap measurement correct, but the gap is to the starter ring, not the flywheel. The ref sensor is above the flywheel trigger. The speed sensor is over the starter ring.