9th Gen Civic Si | Clutch Masters Fx400 Clutch Install

  Рет қаралды 14,842

Just Phil Tv

Just Phil Tv

Күн бұрын

Пікірлер: 92
@chefjimmie1
@chefjimmie1 2 жыл бұрын
Thank you for showing me that this job is way above my pay grade/patience level.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
It’s only rough the first time, if I had to do it again, I could do it in probably half the time, because I figured out where to save time. Plus taking down the oil pan took extra time too
@stephenjones4310
@stephenjones4310 2 жыл бұрын
I really appreciate you putting this on KZbin! You were absolutely right when you said working while on the ground is rough. It brought back memories I had forgotten from 20 years ago when I replaced a clutch in a Saturn. My 2012 Si needs a new clutch assembly and with me being 52 years old......there ain't no way I'm attempting this. You're a better man than me. I'm forking out the grand for a shop to do this.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
Trust me, if push comes to shove I’ll go rent a lift. I don’t plan on laying In the driveway anymore
@Earnyourday
@Earnyourday 3 жыл бұрын
Finally 👏…great job
@brandonmolina3153
@brandonmolina3153 4 ай бұрын
hey phil great video im changing my clutch now using ur video as reference. I have a question, for the driver side axle when you were attempting to take it out and it was seized how did you push it back in from the little bit you took it out. if that makes sense
@JustPhilTv21
@JustPhilTv21 4 ай бұрын
Since the axle was seized, I removed the knuckle from the lower control arm and just pried it out. But honestly the best thing to do is get a hub puller and press the axle out. I didn’t have one at the time, I bought one later when I had to replace the wheel bearings
@brandonmolina3153
@brandonmolina3153 4 ай бұрын
@@JustPhilTv21 Ok cool bet thank you bro
@ThtMillennialDIY
@ThtMillennialDIY 4 ай бұрын
Bro! You went with a 6 puck clutch you wild!!! 😮 how’s it holding up?
@JustPhilTv21
@JustPhilTv21 4 ай бұрын
I’ve put probably about 20k miles on it. It’s been fine
@Fg4alex
@Fg4alex 2 жыл бұрын
What is your set up for the exhaust I seen it and it looks like you got the stock exhaust tip did you delete mufflers or resonator ?
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
Previous owner did a muffler delete, from what I can see it still has the resonator; because it’s quiet unless I’m on throttle. I’ve thought about exhaust options but I’m not sure if I want to stay N/A or go boost.
@redgojira3599
@redgojira3599 2 жыл бұрын
I have boosted 400 hp 2012 fg4 and wanted to replace the clutch im going for masterclutch but not sure which one 300 350 or 400 i have no idea what those numbers differiante
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
Get the 400, the numbers are roughly the torque rating but they can exceed that spec rating, especially if you get the heavy duty pressure plate.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
To be specific, the fx400 is rated for 500ft/lb torque
@redgojira3599
@redgojira3599 2 жыл бұрын
@@JustPhilTv21 thanks for the reply will do !!!
@joeymcquilkin3670
@joeymcquilkin3670 2 жыл бұрын
Spray PB blaster or silicone on those grommets and they slide on and off real easy, so easy in fact that you need to be careful how hard you pull on it to get it off because you’ll bust your knuckles up lol. Definitely kudos for that job man sheeeessshhhhh 😱 * those Acuity bushings are gon change your life 😎
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
You are absolutely right, wish I had thought about it at the time 😂 and yes I love the acuity bushings. I am thinking about getting the skunk2 factory style short shifter next. And I have lowering springs sitting in the cart along with a few other bits
@joeymcquilkin3670
@joeymcquilkin3670 2 жыл бұрын
@@JustPhilTv21 nice man! One step at a time… I just picked up a ‘12 Si coupe a few months ago and it needs a little love in some areas so I try to do as much as I can myself too and then usually like suspension stuff I always send to a shop cuz I don’t like doing that type work on the ground but yea man I really love this car and I can’t wait to do a clutch and flywheel I think it’s really going to change the car
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
an aftermarket clutch is night and day for this car
@Deetzat
@Deetzat 8 ай бұрын
Hey man not to sure if you still post or do KZbin anymore. I’m getting the fx350 installed by me and brother. Where are the exact issues you ran into? I skimmed through the video but my brother doesn’t quite have the patience. He thinks it’s an easy job, but he also did his Subaru where he had to pull the whole motor, and his 5.0. He said with all my tiny parts it’ll be a piece of cake. What do you recommend me picking up for extra help, and where will we struggle with the most you think? He’s a mechanic so he has to deal with axels and rack and pinions everyday, by other than that what do you recommend for making this job easier?
@JustPhilTv21
@JustPhilTv21 8 ай бұрын
It’s not particularly difficult if you have a lift and the right tools. just don’t skip any steps. I made it harder on myself by not pulling my cv axles out of the way, but they were seized to the hub at the time. For best access just drop the entire subframe and steering all together. Once everything is fully disconnected and out of the way it’s just a matter of lowering the engine for clearance and pulling the transmission off. Make sure you have the proper grease for the throw out bearing. And go ahead and get an aftermarket master/slave. also be aware that if you are not using a factory weight dual mass, you will need to tune the car, they cannot use a lightweight flywheel without one.
@Deetzat
@Deetzat 8 ай бұрын
@@JustPhilTv21 thanks. I picked up an oem throw out bearing and the hybrid racing em1 cmc and slave. When you say lowering the engine what mounts have to come off? All of them? I have the hasport rear, hasport upper torque mount with an upgraded transmission mount as well. Could you lower the engine with just the rear mount and transmission mount? or do all all of them have to come off? Thank you for your time, and does the oil pan HAVE to come off? I’ve seen videos where it’s not necessary
@Deetzat
@Deetzat 8 ай бұрын
I also have hondata, I’m pretty sure the misfire detection has to be turnt off. I may be wrong though. I am tuned, but other than that I appreciate the detailed response
@JustPhilTv21
@JustPhilTv21 8 ай бұрын
The only mounts that need to come off are the rear and trans mount, and by lower I meant you tilt the motor because it will drop with those out. And no, I only pulled the oil pan because it had a leak already.
@Dom2.4
@Dom2.4 7 ай бұрын
Is the clutch master still going strong?? After 80k on my clutch master set up Im probably gonna go back to OE.
@JustPhilTv21
@JustPhilTv21 7 ай бұрын
Yea it’s holding up, but I should probably upgrade it. Tbh my lsd is cooked, the extra clamp force wore it out even more than it already was. Eventually I’ll get a built transmission, and rebuild the motor for boost. But that won’t be for some time. I’m working on getting another car and getting out of debt.
@Dom2.4
@Dom2.4 7 ай бұрын
@@JustPhilTv21 by the way, you super impressive doing it on the ground. I get doing like '90s hatch transmission on the ground but doing the k24 trans on the ground dropping the cradle that takes a lot of freaking grit.
@JustPhilTv21
@JustPhilTv21 7 ай бұрын
Thanks man. The first time is always the hardest but if I had to do it again, I could probably knock it out in a day or 2. Definitely wouldn’t do it in the middle of summer, but at the time I really needed transportation.
@jbf813
@jbf813 2 жыл бұрын
I just installed the fx300 in my 9th gen and with the clutch pushed in and in neutral I get a noise about 2 to 3 Grand when I rev it. Any clues? Sounds like the clutch plate trying to grab or something. I also have the exedy em1 CMC upgrade. Is my clutch pedal needing adjustment at the CMC or something?
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
It sounds like you need an adjustment, also too did you grease your throw out bearing when you installed it ?
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
I’m still on stock cmc other than the modding the Slave cyl, i occasionally grind but I believe it’s a synchro issue from previous damage when my car still had the stock setup.
@jbf813
@jbf813 2 жыл бұрын
@@JustPhilTv21 I'm assuming the shop that installed it did grease the t.o. bearing. He has does aftermarket clutches before. Hard to find that sweet spot, I've been adjusting little by little, it's getting better. Thanks for your reply!
@nolby1758
@nolby1758 Жыл бұрын
I've got a 2015si with the throw out going as well. The car is stock, I don't want any overkill, any suggestions on a clutch similar to the oem? Thanks
@JustPhilTv21
@JustPhilTv21 Жыл бұрын
Fx250 full face, or exedy stage 2
@oxyeekithebeatgod2501
@oxyeekithebeatgod2501 4 ай бұрын
Dude I’m literally gonna have to do what your doing soon lol
@JustPhilTv21
@JustPhilTv21 4 ай бұрын
Just gather all the right tools, and make sure you can get the cv axles out the way.
@oxyeekithebeatgod2501
@oxyeekithebeatgod2501 4 ай бұрын
@@JustPhilTv21 I’ll have my bro and my homie from work come help. 3 heads better than 1
@raydavid3230
@raydavid3230 3 жыл бұрын
Just found ur channel. Subbed & bell on . Look forward to the content 👍
@JustPhilTv21
@JustPhilTv21 3 жыл бұрын
Preciate it. man. Hopefully soon I’ll have the next one out
@AdrenalineRushMX
@AdrenalineRushMX 2 жыл бұрын
the good old driveway clutch change
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
Fun times 😹
@charliekim577
@charliekim577 Жыл бұрын
I got it installed on my eg6 k swap. The pedal stiffness is way too hard for me. After break in, does it soften up some?
@JustPhilTv21
@JustPhilTv21 8 ай бұрын
Not by much, I would suggest getting a larger diameter master and buy a new aftermarket slave
@DirtyBroke215
@DirtyBroke215 3 жыл бұрын
💪🏽💯💯💯
@michaelfleming2625
@michaelfleming2625 3 жыл бұрын
great tech
@zeus3473
@zeus3473 3 жыл бұрын
That lawn mower sounds pretty good. Not sure why you had the camera set up behind the car. We want to see it!
@JustPhilTv21
@JustPhilTv21 3 жыл бұрын
Thanks, and I’ll be sure to keep that in mind for the upcoming videos
@daltonramsey9585
@daltonramsey9585 2 жыл бұрын
What was your mileage when you did this? I just bought a 2012 Si with 90k miles. This was the first morning I drove it while it was cold and I’m a little concerned. When I was starting to move the car In first gear I heard a weird sound as I was backing off of the clutch pedal.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
It’s probably your throw out bearing like mine. I did this at 125k
@daltonramsey9585
@daltonramsey9585 2 жыл бұрын
@@JustPhilTv21 I’m hating myself right now. I had a 2019 fiesta with 72 k miles. Got the Si with 90k thinking it would be fun. I traded the fiesta in and paid cash for the difference in the loan (they gave me $12k for it but I still owed $15k), and I bought the Si for $15.9k. Ended up forking over $20k cash (cashiers check). Sucks to have to deal with this now 😔
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
Good lord, that was a robbery. I mean I got knocked over the head for mine too 10k with 17% interest (was in a bad situation at the time ) but that is rediculous
@daltonramsey9585
@daltonramsey9585 2 жыл бұрын
@@JustPhilTv21 car prices here right now Are high for everything. It’s pretty crazy. I paid $18.4K for the fiesta new but I took $4k negative from my trade in so financed closer to $23k. The dealer listed my 3 year old fiesta SE with 72k miles for $17,999.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
Pure insanity, at this rate I could fix the body work on mine and probably get back what I paid.
@rreifschneider7024
@rreifschneider7024 2 жыл бұрын
Thinking about doing this soon! I can work on a car but never removed a trans before how hard is it?
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
It takes planning, definitely on the advanced side. Best if you have a car lift to do this job.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
I followed directions off the forums to figure it out
@Idragonfacei
@Idragonfacei 2 жыл бұрын
I'm hopefully getting a 2012 si coupe that needs a clutch very soon.... Most definitely taking it to a shop for this XD
@therealtruckerbrown
@therealtruckerbrown 4 ай бұрын
need nor of this
@ajreed611
@ajreed611 2 жыл бұрын
Does it work with stock ECU or do u need a flashpro?
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
I bought a stock weight flywheel so I wouldn’t have to flash the ecu. It works out of the box. They do have different versions so if you can’t find the right one, just call them
@Podcastordietrying
@Podcastordietrying 3 жыл бұрын
Lets gooooo
@Fb6_Adrian420
@Fb6_Adrian420 2 жыл бұрын
Did you have any trouble taking off the flywheel too without it spinning
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
I didn’t. I took mine off with a 12 point socket and an impact
@markwells8631
@markwells8631 11 ай бұрын
It won't spin, not unless you remove the sparkplug and probably the serpentine belt, too. The engine compression is enough to prevent it from spinning. If you can, either the piston rings and/or valve guides are shot needing replacement.
@gt-rgaming9452
@gt-rgaming9452 3 жыл бұрын
How is that feel? Because the stock is to week, I prefer the fa5 stock
@JustPhilTv21
@JustPhilTv21 3 жыл бұрын
The feel is slightly stiffer than stock but a lot of that has to do with the fact that I did the slave cylinder mod, it would have been best if I did the mod or gotten a modified/upgraded master too, but I didn’t want to go through the hassle of getting it out. Although, in heavy traffic it can be a pain. It doesn’t like to slip for a long period of time. You have to get the revs up a bit more to get it going smoothly
@pizzaforbakefest
@pizzaforbakefest 3 жыл бұрын
Would it be the same process for a 2014 Si?
@JustPhilTv21
@JustPhilTv21 3 жыл бұрын
Yep, exactly the same. Only difference is my battery is already out of the way because it’s in the trunk
@jkrisch83
@jkrisch83 Жыл бұрын
I’m about to do my soon
@edgarsalinas6408
@edgarsalinas6408 3 жыл бұрын
All those quimicals down to the drainage and to the city water.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
There’s no drainage where I live man.
@fletch8050
@fletch8050 3 жыл бұрын
how do you like this clutch kit?
@JustPhilTv21
@JustPhilTv21 3 жыл бұрын
Man I gotta make my follow up video soon, I love driving this kit, it definitely woke up the car. Even in stock form. It’s an agressive clutch but it still can be slipped just enough to drive on the street. You definitely gotta shift it like you mean it 😂😂
@geradoortega6576
@geradoortega6576 Жыл бұрын
@@JustPhilTv21 how’s the clutch feeling still I’m thinking of using the same one
@JustPhilTv21
@JustPhilTv21 Жыл бұрын
Slightly stiffer than stock. It engages very direct, but that’s also because I took the damper out of the slave.
@JustPhilTv21
@JustPhilTv21 Жыл бұрын
I’ve put on about 20k miles since the swap, no issues, still bites hard like new
@dominicanpapi81
@dominicanpapi81 Жыл бұрын
@@JustPhilTv21looking to get this for my 10th gen si but I’m heading a lot of negative feedback ppl saying that 30k miles clutch starts slipping is this true
@el_Bambino_Kubano
@el_Bambino_Kubano 2 жыл бұрын
Def need to change that Drive Belt.
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
It’s a new belt, just got rust marks from sitting for 6 months
@ogjhernandez2537
@ogjhernandez2537 2 жыл бұрын
You got a IG? I gotta ask you a few questions
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
I do but I’m not active on there. I’ll respond here or you can email me t3chl1f3@gmail.com
@elcuatev8126
@elcuatev8126 3 жыл бұрын
Engin is not fall
@JustPhilTv21
@JustPhilTv21 2 жыл бұрын
I had a jack holding the engine up and the top engine mount was still attached
@agnesleung1010
@agnesleung1010 3 жыл бұрын
Love the install! Do u have IG?
@JustPhilTv21
@JustPhilTv21 3 жыл бұрын
I do but I plan on creating a seperate one for this channel. More content to come hopefully soon.
@blackangel181588
@blackangel181588 3 жыл бұрын
💪🏽💪🏽💯
2014 Civic Si stage 3 clutch master replacement
20:09
VangMotive
Рет қаралды 10 М.
Honda Civic Si action clutch stage 2 Install 9th gen 2012-2015
17:10
Pablo's Garage 707
Рет қаралды 11 М.
How I Turned a Lolipop Into A New One 🤯🍭
00:19
Wian
Рет қаралды 13 МЛН
ЛУЧШИЙ ФОКУС + секрет! #shorts
00:12
Роман Magic
Рет қаралды 10 МЛН
Seja Gentil com os Pequenos Animais 😿
00:20
Los Wagners
Рет қаралды 67 МЛН
Wait for the last one 🤣🤣 #shorts #minecraft
00:28
Cosmo Guy
Рет қаралды 17 МЛН
Hondata Flashpro Tuning 101
39:25
BULLI KID
Рет қаралды 27 М.
Honda Civic Clutch Replacement!! (Si)
53:25
Daniel Kellert
Рет қаралды 88 М.
How a Manual Transmission and Clutch Works
10:23
Animagraffs
Рет қаралды 3,5 МЛН
9th Gen 2012-2015 Honda Civic Si transmission removal
15:52
RockTsProjects
Рет қаралды 1,4 М.
Why People Love Honda's K20 So Much?
12:21
VisioRacer
Рет қаралды 673 М.
INSTALLING THE MAKSPEED TURBO KIT (9th Gen Civic SI)
17:50
dc5diego
Рет қаралды 15 М.
clutch masters fx300 for my k24
12:23
The mech a nic
Рет қаралды 6 М.
How I Turned a Lolipop Into A New One 🤯🍭
00:19
Wian
Рет қаралды 13 МЛН