A quicker easier Stealth Shelf.

I showed you how to make a stealth shelf before but that one was kind of a pain in the a$$. Here is a quicker simpler way to make one. I used a different lock on this one too.
Slow open air spring : amzn.to/3E43j0q
Motion Sensing Light : amzn.to/3m1rGG5
Hinges : amzn.to/3FnwFrE
RFID Lock : amzn.to/3JwhwHQ
Magnetic Locks: amzn.to/3b37AVm
Foam : amzn.to/32Ua1cJ
I found the foam on Ebay under the description
Customizable Polyethylene Foam Pads for packing and crafts, 1.5 in

[@toyT100]

Mans said fuck it, I'ma put a shoe box on my wall and hope no one assumes a firearm is in it 😂😂😭

[@LastLeafStudioVideo]

🤫🤫🤫🤫😂

[@OBSLyfe]

That's some funny shit 😂😂😂

[@jack_knife_customz2966]

This is so nice. The only part messing me up is how’d you know the spacing for the reader.

[@tooshieg2059]

Luv it! Thanks for sharing. Although, I hate locks that click and beep when opening

[@LastLeafStudioVideo]

Hmm I wonder if there are silent ones? I know there are magnetic ones.

[@race091]

That's kick ass I like it

[@LastLeafStudioVideo]

Thank you

[@gruss5157]

Saw this video 🎉 subscribe🎉 great job two thumbs up

[@LastLeafStudioVideo]

Thank you, thank you

[@rogerthatusa]

Right to the point. Good stuff

[@LastLeafStudioVideo]

Thank you

[@MLopez-lw2ct]

I like the build. Did you show how to hang it or did I miss it?

[@LastLeafStudioVideo]

I guess I didn't. If you watch the end you can see two screws on either side of the light that go through the back piece.

[@oincer3943]

What type of wood did you start off with and measurements ?🤔

[@LastLeafStudioVideo]

It's pine with a dark Walnut stain. I'm pretty sue the top measured 18" long x 10" wide plus the pieces around the edge. Sides of the bottom are 1x4 measured to fit inside the top with an 1/8" gap all around except the back.

[@vuztamante]

❤

[@LastLeafStudioVideo]

😎

[@joestatella1049]

Where did you get the lock from? Do you have a link?

[@LastLeafStudioVideo]

Just added one to the description. amzn.to/3JwhwHQ

[@smgibv4393]

Quicker amd easier than what/which one?

[@LastLeafStudioVideo]

This one kzbin.info/www/bejne/r4PSgp6Cj8R9p5I

[@1991DesertVet]

Are you using the Ryobi brad nailer or pin nailer? Which one do you recommend?

[@LastLeafStudioVideo]

This is the Brad nailer. I would actually recommend no nails for this project, but I am very impatient so I used them instead of clamping.

[@1991DesertVet]

Thanks for the info. I would rather build them faster too. Plus it would give more peace of mind that they won't come apart.

[@LastLeafStudioVideo]

@@1991DesertVet yeah it's always nice to have that little bit of backup

[@1991DesertVet]

Yep. I'm planning on going to Home Depot to buy one today. Gotta try out my new table saw now too.

[@LastLeafStudioVideo]

@@1991DesertVet nice. Good luck

[@johnrenas5754]

where can i get the open and close mechanism?

[@LastLeafStudioVideo]

Link in description I think

[@keithmotley2268]

what hinges did you use ?

[@LastLeafStudioVideo]

@@keithmotley2268 110 degree full overlay hinge

[@SLickev92]

What’s the point of the groove made at 2:20?

[@LastLeafStudioVideo]

You have to knock that corner off so it will close properly. Yeah I didn't do a good job showing that.

[@SLickev92]

@@LastLeafStudioVideo oh okay got it. That top piece is 18x12 right? Nice build.

[@LastLeafStudioVideo]

@@SLickev92 I believe it's only 9 1/4 x 18 but I can't remember. I'm sure 12x18 would be just as good if not better

[@SLickev92]

@@LastLeafStudioVideo ok cool . 9 and a quarter sounds better cause I’m trying to keep it more compact .

[@user-kn8lr3zm8u]

7:37

[@LastLeafStudioVideo]

What is it?