A super easy lazy way I did it ,was to use D clips or caribiner clips to attach panel gates right to my existing fence.😆 I did that for a few years. Just now creating pens with post corners and framed out gates. It takes a while getting started. You do what you can. My sheep don't care what my gate looks like.😆
@SimplyMadeHomestead3 ай бұрын
This is true! As long as it works is what counts.
@beerock76178 ай бұрын
Thank you
@SimplyMadeHomestead8 ай бұрын
You're welcome
@DrewJacobson619 ай бұрын
Great idea! I think I’m going to use this. God bless
@SimplyMadeHomestead9 ай бұрын
Wonderful! Thank you so much for joining me.
@joshpatrick880911 ай бұрын
Thanks! I had to build a quick pen for my dog that just had puppies and had some panels left over from my garden trellis, but didn't want to waste a bunch of wood building a gate.
@SimplyMadeHomestead10 ай бұрын
Glad it helped!
@HM-oy1cm6 ай бұрын
Exactly what I was looking for. To build a fence with the same cattle panels, how far apart do the t-posts need to be? I'm using a total of 2 panels, gate included. Also, how to attach this gate to t-post rather than wood? Thanks so much for the easy instructions!
@SimplyMadeHomestead6 ай бұрын
Glad to be of assistance! How to attach: I had some heavy 9 gauge wire that I made a loose fitting loop with. You could remove the barbs from barbed-wire fence and use that too. You could even use rope, but that would be just a temporary hinge. Now to keep the gate closed I put a 1” pvc pipe into the ground where you want it to be closed and attached a straight metal rod to the gate. This will secure the bottom off the gate. And finally I use another piece of wire on top of the gate to fasten it to the fence. As for the spacing, I am not exactly sure what you mean so forgive me if my answer is off a little. While putting up the panels as a fence, I will use 3 T-posts for every panel section, but overlapping each panel by 8-10”. This way two panels will share a Tpost. So if you are only using 2 panels together, that’ll be 5 Tposts. But it will depend on what you’re using it for. I also have 350-400# hogs and place an electric wire on the inside to keep them off it. I hope this helps, I will try to send a pic of the gate for clarity when I feed the animals this morning.
@SimplyMadeHomestead6 ай бұрын
I am unable to send pics or video through this chat. I did take a couple videos of various examples I did here for better clarification though. If you want them, text me at 423-888-7724 and I will send them to you. I am going to delete this thread tomorrow because of my cell number!
@beerock76178 ай бұрын
I hope you are still monitoring your KZbin. I noticed you have a garden post that is at an angle with your upright post. You have them wired together at the top. How did you secure the bottom of the angled post?
@SimplyMadeHomestead8 ай бұрын
I drive the T-post into the ground about 6-10” at approximately the same angle. It took several attempts to get figure out the right distance/angle, but it works out well! But if you didn’t do that, you could use some pressure treated wood as a stake at the end. Yes, I just used wire to secure the top and at the sides to the fence. They do make a contraption specifically for Tposts to joint the tops. I think they are about $20 at TSC. Hope this answers your question.
@gailstark1688 Жыл бұрын
You are to far from your speaker. It's so hard to hear you.
@SimplyMadeHomestead Жыл бұрын
I’m sorry about that. Thank you for watching though. I don’t know which video you watched but in the beginning I didn’t have a microphone but now that I do, I try to wear it whenever I make a video. Thanks for letting me know though.
@gailstark1688 Жыл бұрын
@@SimplyMadeHomestead it was the video in Make A Farm Gate Using A Panel. But no worries I just wanted you to know. Thank You!