Ab Hoga TURBO INSTALL🔥🚀Sound Sunlo Kesi Hai💯

Hello everyone... hope this video is verry helpfull for you
dont forget to share this video....
My new vlogging channellink👇🏻👇🏻👇🏻
/ @rammyryderr
for new updates you can follow us on Instagram 👇👇#supercar
/ ncr_motorcycles. .
#turbo #turbocharged #turboinstall #installing #desi #jugaad #working #turboinbike

[@sv6743]

This will be the most comprehensive guide to turbo charging your bike - 1. You need to retard the ignition timing according to the fueling of your engine 2. You absolutely need bigger injectors to account for the additional fuel being injected for the added air volume 3. As you said it absolutely needs a oil line and while you are at it make a oil cooler with a fan as well because turbo will heat the oil astronomical values and alsoit needs a additional intercooler for the intake to cool down the air charge for maximum density of oxygen 4.For serious power gain you need lower compression forged pistons and a forged crankshaft and complete bottom end rebuild like uprated bearings and oil squirters will help keep the piston temps low 5. Along with a built bottom end rebuild you need Racing spec camshafts with higher lift on both intake and exhaust side and porting and polishing of the intake ports is highly recommended to allow the higher volume of air to flow through 6. You need a K&N bigger air filter to allow the higher volume of air to flow easily into the engine 7. Full system exhaust is a must with calculated diameter for the headers and exhaust pipe 8. The closer the turbo is to the exhaust valve the higher the power that is captured from the heat of the exhaust gases 9. Use a heat blanket on the exhaust side of the turbo to trap the heat of the exhaust gases inside the turbine housing for maximum efficiency 10. All the added power will eat throught the gearbox within 1-2 turbo spool on road so you might want to strengthen the gearbox gears as per requirement and the clutch definitely needs a few more clutch plates and stronger springs to cope with the power 11. Custom ecu is a must in any turbocharged application to fine tune the aspects 12. Along with uprated injectors the stock fuel pump will burn out in like few hours so a bigger fuel pump is also needed 13.If you tune the bike for race fuel i.e E85 you can multiply the power output upto 2 folds and it'll run way cooler as E85 inheritently cools the engine when injected into the cylinder 14. After all this a proper rolling dyno tune is necessary to make all of this work in harmony together 15. You need to use a low knock index fuel to prevent knocking and destroy your engine due to it 16. Needs better brakes and bigger rear tyre to put all that power down to the road and a longer swingarm to prevent front wheel lift(wheeling) when boost comes on 17. You need head bolts with 3-4 times the strength of the stock ones and a better head gasket if it's a open block design it's advisable to strengthen the gap between the cylinder wall and block the cavity for the coolant to flow through 18. You absolutely need a wastegate to control the boost and if you are installing a wastegate a blow off valve is not needed 19. On a completely different note if you are planning to make the turbo work with the stock internals be very conservative on the boost and only plan to extract 20-25 horsepower at max as anything more ought to blow the stock block apart and throw some rods 20. The valve guide need to be changed to higher tolerance ones and valves need to be changed to a racing spec to cope with he aditional heat produced in the cylinder If you do this you can easily extract 100+ bhp from the bike Some hayabusas are tuned to the extent of 800-900 bhp so horsepower isn't the limit here it all depends on how much you have strengthened the components to account for the additional stresses Hope this helps wish you all the best

[@shreyaspandey2401]

Really great❤

[@sv6743]

@@BBTrajchallenge yes 600 cc can be turbocharged the displacement doesn't matter much, you just need to find the correct volume turbocharger suitable for a 600 CC engine but without strengthening the stock internals it's not going to work because turbocharging generates a lot of additional stresses on the engine components and NA engines are no where strong to handle a turbocharger application

[@sv6743]

Rummy bhai I strongly suggest you get a procharger instead of a turbocharger (the one used on the ninja H2 is a procharger) or a centrifugal supercharger as they are available in smaller sizes

[@pratyasaha9876]

media.tenor.com/ZZxiLJenbewAAAAd/respect-salute.gif

[@pratyasaha9876]

👍👍

[@chinmaypanda023]

Bhai, intake air ke liye toh intercooler lagana hi padega kyunki agar intake mein garam hawaa jaayega toh uska koi matlab nahi hoga kyunki uss mein oxygen ka density hi bahut kam hoga

[@sayantanmanna2801]

Bhai garam hawa firse ander jaegi engine me kon bola ... Exhaust ke through Jo tarbo wheel ghumega usse bahar se air ander jaegi

[@chinmaypanda023]

@@sayantanmanna2801 acha. Toh manufactures turbocharger ka blower ke exhaust mein ek intercooler kyun lagaate hain ??

[@justinbiebervevo915]

​@@sayantanmanna2801 bhai kisne kaha exhaust air wapas garam wali engine me jaegi Nahi wo nahi Magar wo air jo exhaust se ati h garm hoti h us wajha se turbo ka metal garam hota h us wajha se jo air banegi wo garm hokar jaegi na engine me. Ye us air ki baat kar raha

[@shivamsavita3495]

Exhaust gas nhi jayegi lekin fresh air turbo se compres ho ke jayegi to vo garm ho jayegi kyunki kisi chij ko compres krne se vo garm ho jati hai isliye intercooler lgate Hain.

[@chinmaypanda023]

@@shivamsavita3495 compress karne se garam hoga aur jo exhaust gas hai uss se heat transfer ho ke blower section mein aayega. Toh wo bhi heat ko add-up karega

[@ultrongameing9562]

Finally turbo modification culture cm to India, happy to see this 🎉❤

[@bikersukhi3492]

FROM TODAY ITSELF, 5-6 YEARS AGO I DID THIS IN MY DUKE 200 AND IT RAN SECCESSFULLY

[@JinSakai_Kuroudo]

Using a turbo without an intercooler is only done in india 🤦‍♂️ 😅, half studied engineers who smoke weed throughout their college are to blame. People are either chappri or nerds, there are no real gas monkeys in india

[@sigma1015]

Bhai king Indian ne bhi Kara hai rummy bhai ne hi karke Diya hai

[@pawansagar001]

whistle Sound is amazing 🔥

[@jestonfernandes5324]

Bro u r full boom Bang boom 💥💥 at 0.58 🤣😂

[@kishorevenugopal6191]

Eagerly waiting for the next few videos!

[@PriyanshuV8]

*Bhai agar turbo lagaoge to intercooler bhi to lagana oadega kyuki turbo ki hava garam hoti hai!*

[@theamitavadewan]

Gr8 Rammy Bhai, Carry on. You are going to make history and world record 😲😀😍💖👍🏍️🔥🇮🇳👌

[@sameerp8601]

Use 12 volt mini oil pump or container Use rubber hose pipe for bettter efficiency Don't cut expensive exhaust pipe 😅

[@Arnab1violin]

Turbo ka itna sahej explanation dene ke liya thank you. Akdam clear ho gai

[@pitsplaces]

oil filter ke wahan se outlet lia jaa sakta hai oil ka, filter separate karna padega lekn. Oil filter ke outlet se se oil turbo me, wahan se filter me and wapas bike me.

[@s.prabhdeepsingh]

Just waiting for turbo gsx s750…🔥🔥🏍️

[@manishmv]

bhai tumhari jitni tareef karein kam hai. Really !Really ! good work

[@kunalsharma9488]

Some suggestions: 1. Use high quality performance air filter like K&N 2. Air cooler/After cooler/Intercooler lagana padega else useless kaam h 3. Radiator ko bhi mody farke zyda fins wala lagana padega 4. If availaible use API SP class oil of the same visco grade. 5. Upgrade oil filter to a high quality one. 6. Try to provide lubrication with additional pump as well and try to have Lube oil low pressure trip system. Suggestion: NEVER EVER EVER EVER RUN A TURBO WITHOUT LUBRICATION EVEN FOR A SINGLE SECOND!!!!! TURBO CAN GO TO 50000 RPM!!!! YES YOU READ THAT RIGHT.

[@AbhishekPathak21]

I don't understand the use of K&N air filters outside tracks/occasionally power rides. It provides more air but at the cost of air quality which is not ideal for extended use. What do you think?

[@alisonphoenix3159]

best comment section i ever seen ❤️ sabhi ko knowledge hai engine ka.....turbo ka 💐

[@kirankoli852]

Teen major update kene hogay 750 may, tub jaake power jaad de gee. 1 :- ECU ko dyno se update kar ho ga, 2 :- Bade cc ka injector, 3 :- jaada flow wala fuel pump,

[@gogia_amit]

Rummy bhai karo tayar, best of luck.

[@Mobilerepairsolutions07]

Its good but bhai jab aap turbo ko connect karo ge exhaust se jab air out hone ke baad air jab ingine mai in hogi toh pistan ki speed bade gi toh crank brake ho sakta hai so turbo 1000 wala he lagana ya us se kam . Maine koshish ki hai

[@LEXES375]

This video got millions of views soon

[@roshaansheikh7791]

History mein Amar Ramy bhAIi😅😂😂 bus krdo yeeee ek bar

[@freaky6995]

Bhai apki video bhot phele se dekhra hoo acha Lagta hai jbb apne Desh Kai log bhi , aisi kalakari karkai bawal cheez bana dete hai ❤

[@Bottong1010]

Turbo install karo Love from Bangladesh 🇧🇩

[@avishekdutta5990]

Vai ❤ bht knowledge mila Thank you so much❤❤❤

[@nathanaelkhandagale9512]

Please make a video on 2001 model old bullet brake lever switch with connection and fitment.

[@shaileshnagargoje5654]

Maine ek rajnigandha ka can liya usko 2 inch hole Kiya. Fir splendor ka silencer ekdam end wala part cut Kiya aur rajnigandha wala can waha fit Kiya aur silencer pehle ki tarha weld Kiya.(total 150 rs) Ab ktm jaisa exhaust ban gaya aur bike pe asar bhi nahi hua.

[@aasifansari2436]

Bhai h2r wala sound ayega ekdum zuuu...wala turbocharged engine 😊😊

[@proriderf2509]

All the best beheya I hope apka experiment acaha rahe 🥺🌚💖

[@amitnariya2863]

Thank you so mnch sir

[@hanishverma3629]

Bhai aap ertiga 1.3 ya breeza ka turbo lga skte ho agr aap VGT tune kra Pao us se aapko lag km milega or power zada

[@prateekjaiswal2557]

Bhai indori exhaust ko stock exhaust type banado welding kerke 💯 please

[@letsdosomething7553]

Waiting... Mai to kb se wait kr rha hu turbo charger ki fitting sikhne ke liye merko apni bike ko turbo charger bnani h...😊

[@texteditz4457]

Lagadijiya sir😊

[@ajaykarahale1348]

Each turbo has waste gate which is operated by ecu ,if u directly connect it air intake u will blow ur engine at higher rpm so it not an good idea

[@johnwick66gaming77]

Extra oil Can Aur Pump Best Hai Bhai ❤

[@kushalraj9665]

Install turbo in royal Enfield 350

[@fvgbilalyt6179]

🧑‍🔧

[@vaibhavpandey1666]

Bhai isme Celerio diesel ka turbo use karo usme 800 cc ka diesel engine aataa tha ! Uska turbo isme sahi aa jaana chahiye

[@kaku-5888]

bhai mat lagao bike mai yr intercooler wegrh sb lagao ge turbo ko oil supply dena bhi muskil hai es bike mai... car mai lgalo bas

[@toufiqiqbalnajar3174]

Bend pipe mat cut karo new banavo

[@ashunegi3015]

Sensor ki Requirement bhi to hogi...jo 1500-2000 RPM pe turbo ko Boost bnane k liye Signal de....or Extra Pressure hone pe Wastegate Close kr de

[@MSK2210M]

MARUTI CELERIO DIESEL 800CC KA TURBO INSTALL KARO SWIFT DIESEL KA ENGINE 1248 CC KI HAI EXHAUST PRESSURE KA KAAFI FARK PADEGA CELERIO DIESEL 800CC TURBO AUR GSX 750 CC ALMOST BARABAR BOOST PRESSURE HOGA REFERENCE KE LIYE YAMAHA R7 TURBO VIDEO DEKH SAKTE HO APP 👍

[@aarshislive]

Brother' bullet also have hi compression and bullet can easily spool the turbo pls try 🙋‍♂️🙋‍♂️🙋‍♂️

[@kvkulkarni007]

Aap ko intercooler bhi saath me laga padehga, hawa ko thandi rakhne ke liye.

[@Durgvijaygoogle]

Best of luck bhaii🎉🎉🎉

[@rahul.k5818]

Yes sir 🎉

[@AftabAnsari-wf1lp]

भाई लगा डालो ❤❤

[@gurjitsingh8572]

We,re waiting to see it

[@youtubersachinsk9201]

bhai jaldi 2part laoooo very exiting

[@Official..dhiman]

Maza aaye ga turbo k updates dekhne me

[@varshapise8678]

Bhaiya gt 650 pr laga shakte ho kya

[@Maina1981]

Mast

[@nareshkmr0786]

bhai plz one video on Standard 350 bullet tyre upgrade 110/90/19 original rimmrf meteor mo grip(tube) 110-120/80/18 rim change 19 to 18inch bhai plz suggest krdo

[@Bhupsinghbindra30]

Karo Karo ❤

[@manishmv]

bhai bahut pyaare ho aap!!

[@jaydevsingh3067]

Broooo that turbine sound♥️

[@mdgousepasha886]

Nice improvement 💯 Mashallah

[@ritesh747august]

Without intercooler it is going to fail. But nice content for brainstorming.😅

[@ankitojha6684]

bhai turbo lagao apni paaro me bahi ye project dekhna h

[@mdsaifuddin512]

Hello brother Apache RTR 160 Arrow fitting video turbo performance❤❤

[@luckykhanshorts4262]

Bhai Aag lga do

[@imlimongba6182]

Sir I want to know... Can thunderbird tank fits in classic 350

[@electrotech7633]

bhai intercooler lgega he wrna boost. boht late late ayega kbhi ni aayega 😅

[@pramodshendkar6443]

Sir try it once on Himalayan engine because it is oil cooled or hero xplus

[@Yogeshkumar-ij4mh]

just deadly waited to see this project .......

[@suhailawm5240]

Bhai i.m existing ❤❤❤❤❤

[@MaharashtraRider681]

Classic 350 BS6 Mein bike chalu hone ke bad hi light on Hoti Hai vesahi BS4 Me Kuch kar Sakte Hai kya bina Wire Cut Kiye Bike Chalu hone par hi Light chalu ho

[@ShahbazAhmad-st8kn]

Veri nice

[@sonusam7349]

nxt video kb......

[@Asif-pi2ql]

Bhai mujha Yamaha yb100 ma lagani ha fit hogye ga or konsa turbo acha ha uska lia thora guide karna please

[@rahib8523]

❤❤❤❤😮😮😮🎉🎉🎉🎉

[@subhadeeppatra7527]

Bi Karo ham log bohot excited ha

[@dhagai]

Bhai aap ku advice chahiye bike ko lambe samay tak use nahi karna ho to kya karna chahiye? 1 saal tak agar nahi chalegi to uske liye kya karna chahiye. Saal mein sirif 1 hi mahina chalegi. Aap ki kya advice hai mujhe kya karna chahiye. Mere paas classic 350 hai. Abhi kharidi hai Agar aap se phone pe baat ho sake consulting ke liye to bataiyega

[@rajawatabhay4386]

Only turbo se kuch nahi hoga sir pura system retune hoga tab performence achi hogi

[@chetanpatil2612]

If it works then it's 🔥🔥🔥🔥

[@user-pn3gr9yp3y]

👌👏

[@utkarshseth2489]

Majaa aa gyi

[@shujakhan8796]

Bro you are living my dream

[@sangitadas5456]

Part2 kab aya ga

[@darksoul4721]

Bhai log kisko King Indian yaad aagaya?

[@deepmathukiya8732]

sigle cylinder me lagana hai turbo ...uska koi video banav

[@lakhanahir6535]

Bhai jaldi ane do next episode

[@codebury6343]

Puri video mein lagunga lagunga batate rehe Gaye bas😂😂😂

[@shrinathwable1978]

Sir ji , Meri clasic 350 2015 modal black smoke & missing problem de Rahi hey, sab jagah dikhai koi solution nahi nikala , sab kehte ki half engine kholana padega

[@mr.jyotivlogs]

❣️

[@Sukhvir_Rider]

Bhai hunter 350 lene ki soch reha hu kaise regegi hunter bike..plz tell me..

[@utkarshseth2489]

Bhai ek baari Avenger 220 me bullet 350 ka engine laga trykaro please

[@crank_smashers]

Pulsar ns 200 me turbo dalne ka kya costing ayega sir ???

[@newsong6541]

bhia ek video banaa do standard bullet he lite battery per kaise karen interact bine wire kate battery ko direct kaise karen plzz bhia bata do

[@montukvideo3399]

Old bullet me lg payega kya ...agr lge to old bullet me hi fit kro bhiya

[@SurajVerma-dq8ht]

❤

[@dineshshrivastav6234]

Bhai bullet classic 350bs4engine fitting labour charges kya hey Bhai jarur se batana👍

[@amjadalikhan1262]

All the best bro🤜

[@rohhitpatel1482]

Rammy bhai ek bar yamaha rx100 me turbo try Karo kya Hota Hai.!

[@sudiptamondal3881]

Sir can you please tell me from where I can buy stainless steel spokes for my Royal Enfield ES uce bs3. 🙏

[@Madworld23l]

Interesting 👏👏👏

[@yagu_stunts]

👍👍👌👌

[@shubhamdubey2277]

Bhai isme oil cooled nhi h to fir konsa cooling system hai

[@rahisrahiskhan9934]

Lagao bhaiya ham bhi dekhenge kaise

[@altabansari4800]

all the best

[@kaushikrokdevlog7106]

Maruti Suzuki celerio diesel ka used kar bhai... vo engine 789cc ka engine hi