ABS Removal BMW S1000RR 2020 (K67) and inst Thumb brake

How to remove the ABS on the new BMW S1000RR. and inst. thumb brake

[@1980jamesm]

Handy tip for removing the abs metal lines, cut them by the engine bolt, then they pull out pretty easily. And RS2e now sell a ABS pump cover, thats quite a bit cheaper than the Alpha one. Thanks for the helpful vid!

[@scholterclassicracing7424]

Keep up the vids, they’ve massively helpful during my track bike build this year!!!!

[@omidanka8785]

Thanx

[@davidd6786]

Omid Anka muchísimas gracias. Por tus videos 👍

[@omidanka8785]

Garcias a ti para ver lo :)

[@kemalacar8049]

Hi Omid, nice movie. I am about to get my 2021 s1000rr within 2 weeks and after running in to transfer it to a trackbike. Just a question, what rear brake cilinder are you using? I also intend to install a thumbrake and likely to keep the footbrake as well. Thanks.

[@omidanka8785]

Hi Kemal. Congratulations. I am using : www.omniaracing.net/en/rear-brake-master-cylinder-discacciati-racing-for-thumb-index-air-hole-lever-p-117843.html If you have the money I would go with: www.ima-specialparts.com/products/tbs-thumb-brake-system/?lang=en Hope this is helping. Best reg. //Omid

[@kemalacar8049]

@@omidanka8785 Hi Omid, how is the RR throttle? Is it good for track and working properly?

[@omidanka8785]

@@kemalacar8049 hi. Its ok. Ut i charged it to get shorter travel. I have a video on that so check it out ;)

[@davidd6786]

Omid Anka.Buenas noches. Mi bmw es como la tuya! Trae de serie un neumático 190/55/17 y le quiero montar 200/55/17 . Si lo cambio?. Tengo que hacer alguna modificación. Gracias

[@omidanka8785]

en realidad si pero tienes que ir al un workshop para haser esso Ellos conectan un compotadora y cambian el setting.

[@davidd6786]

@@omidanka8785 Como siempre hay!!!!!👍✌Muchas gracias

[@davidd6786]

Omid Anka, Buenas tardes. Cuando puedas pon el vídeo desmontando las ruedas de la moto. 🙏🙏🙏

[@omidanka8785]

si claro :)

[@nickzachery7995]

Is it the same process on S1000RR 2014 Gen 2 ? Cool Video Man.

[@omidanka8785]

Thanks man. I have no clue but in theori it should be the same

[@markfletcher885]

Great vid. Just done abs bypass and thumb brake on my k67. Get an error when moving off about abs and then half a lap in the speedo goes to 3 dashes - - - does yours do this ?

[@omidanka8785]

Thank you . i did not get any errors. I send my display to RS2E to avoid faults like that. Hope it sorts out.

[@neillatham4742]

Great video. Excellent

[@omidanka8785]

Thank you 🙏🏻

[@davidd6786]

Echo de menos ya un vídeo Omid

[@omidanka8785]

Sorry no tango tiempo ahora y la plata se acabo si que no puedo comprar nuevas partes:). Pero despues de navidad ojala que podia hacer uno

[@davidd6786]

@@omidanka8785 🙏👌👌👌🇪🇸

[@ericwilliams1977]

Just wondering, if I get the Alpha Racing ABS delete module to plug in, I don’t need to separate the ABS pump from the black plastic electrical controller right? Just get rid of all of it?

[@omidanka8785]

when i deleted the ABS there was only this option. so yes, if you get the module you can remove the complete unit

[@FirstLast-tx3yj]

​@@omidanka8785i want to fit an endurance tank( the one that extends under the seat) but the current problem is I have to relocate both abs and battery) I know this is very different from everybody else but I do not want to remove the abs and I have already bought an earthx battery and laid it flat in the tail. I was thinking about relocating the abs module either next to the exhaust merge where the bulky muffler was or to the front under the oil radiator Since you have knoweledge on the lines and the unit could you please give me you opinion and what would you reckon be the best option??

[@omidanka8785]

@@FirstLast-tx3yj So it comes down to 2 things weight distribution and space. The lines are hard pipes as you can se so its hard to use the original and modd. the bike has already a lot of weight in front so i dont recommend under the oil radiator. weight wise it is better to relocate here the cat was ( muffler ). What you have to consider as well is the calibration of the ABS pump. the pump calculates stuff depending on the pressur and if you change the lines routing you may have different pressure resulting in fail of ABS. I strongly recommend to remove the ABS if you are using the bike on track. I have never ever used the ABS on track,

[@mohammadalomair1968]

Amazing video bro thanks a lot... What's the actual weight of the abs pump module that you removed?

[@omidanka8785]

Thanks, The ABS is 1 kg and the breaklines 0,5 kg so 1,5 kilo saved :)

[@s1kking36]

What did u go with for ur ecu flash

[@omidanka8785]

Rs2E (www.rs2e.de/leistungen-preise/katalog-bmw-pkw/) i got great service and the flash is perfect

[@RS2E]

Hi, great video again, I think many others out there will be glad to have this instruction video. But allow me one remark, it‘s mainly Instrument cluster which has to be reprogrammed to disable ABS error messages. Further info here: www.rs2e.de/en/services-prices/catalog-bmw-motorrad/disabling-of-warning-messages-modification-of-bike-configuration/ Greets from Bavaria, Rainer

[@omidanka8785]

Thank you for the excellent remark. I for shore am very happy with my flash with you guys and the support I get with all of my novice questions.

[@adzventurerider]

Any way to get pressure back to get data.

[@omidanka8785]

Hi, Sorry you need external pressure sensors if you want to logg the pressure :(

[@jieevo]

Will a tune get rid of the error code? I have brentune

[@omidanka8785]

I don’t know about brent but rs2e.de will get rid of the error codes for you

[@marc15skate]

do you have any error code ?

[@omidanka8785]

You Will have abs error on the display. The Rs2e guys in Germany can fix that for you www.rs2e.de

[@kasushi]

@@omidanka8785 how do they fix it? We have to send the ECU for them?

[@omidanka8785]

@@kasushi not the ECU you need to send the display to them.