ADO DECE 300 D30C Hybrid S830 Settings - Switch from 3 to 5 Assist Modes

[@TechTronic9000]

ADO bikes & accessories are available from the official shop bit.ly/OfficialStoreADO ADO spare & upgraded parts can be found on the official AliExpress store bit.ly/OfficialStoreADO_AliExpress You can now also join the Official ADO users group facebook.com/groups/adobike01

[@jeffmitchell7071]

Great video that really helped me with my new bike - thank you! Will you do a full video of the other settings that you mentioned?

[@qweasz562]

show a video where you show about the settings of the Display 830

[@ultimatestnovae]

Thank you for the video with useful information, where do you find all these instructions ? are they documented anywhere ? I can't find it in the manual.

[@TechTronic9000]

I'm just passionate about these things, this is not documented by ADO as they don't want everyone to change the settings wrongly as they had a lot of issues with customers that changed things in that menu and then claimed that their bike were faulty. So they properly test and configure then before shipping them so regular users don't have to.

[@ultimatestnovae]

@@TechTronic9000 thanks for the fast & detailed answer !

[@wnight55]

Good tutorial, thanks, I be in touch. I have 3 of these. time for troubleshooting now that I know the display

[@TechTronic9000]

I'm glad it was useful, thanks for watching and I hope that you have subscribed.

[@FernandocraftAnimador13]

I recently got a bike with the exact same display and controls but when I got into the settings I can't change anything, only the the brightness and the speed limit, I cannot change any other settings even if they appear there. Is there a way to do it or maybe it's the bike?

[@kenleckie2359]

u have to write into setting mode .turn on screen and with in 5 seconds press up and down buttons at same time 1st Will be light bright 1 ,2,and 3 then hit M button and that will be P02 setting then use up down to adjust. extra but it doesn't give you much time to do your setting and will time out like in 4 or 5 seconds and go back to home screen. if it does do over hit M button as men by times to get you back e.g. Po6 and continue to I believe p14 .hopefully it helps you

[@TechTronic9000]

The controller could be locked, they display only sends the commands to the controller.

[@gabrielb8240]

Very good video. Thank you for info!

[@TechTronic9000]

Glad you enjoyed it!

[@petelato]

very well done, thank you so much...Are you aware of any way to set each PA level? PA1 is way too strong, I want some PA, not a lot, not seeing anyplace to tweak that...could be a deal breaker for me.

[@TechTronic9000]

You can only set motor acceleration strength and assist delay but that works the same for all modes.

[@petelato]

@@TechTronic9000 bummer..... thanks.

[@churcher8334]

You need a torque sensor for power assistance. Not a cadance . There are some good cheap ebikes out there with them. Some of the eleglide range have them .

[@lovestone1963]

cant find the promised vid on other settings....how do you change from km's to mph? Cheers!

[@TechTronic9000]

Here is the full video kzbin.info/www/bejne/qYOzfISga8iUZqM

[@DOCWHOK9]

Hi, great video on the settings, wondering if you have upgraded this controller, this is what I'd like to do, despite the UART Color being the same, I have no power. Computer = S830 UART Compatible Computer Upgrade = Bafang 860c UART Color display

[@TechTronic9000]

No I haven't upgraded it. Sadly these controllers and displays are not very well documented so can't find a lot of resources about them.

[@SuperSpily]

Hello my friend, these settings are fine even on an ADO A16 + to not have the hamster effect when pedaling?

[@TechTronic9000]

I think that the A16+ comes with the S866 display, check my other videos where I also cover all of its settings.

[@Andsk7]

Your videos are very helpful! Is it possible to unlock the pedal assist and get assistance from motor even if you pass the 25 km/h (without using throttle)?

[@TechTronic9000]

Sadly on this controller it's not possible to get assisted mode working faster than 25km/h.

[@Andsk7]

@@TechTronic9000thank you! one more question. When you level up the assist modes do you get extra torque apart from a higher speed limit?

[@cassianstaschinator9399]

@@TechTronic9000is it possible to Change the controller

[@johnleithead4652]

I am wondering if there is a way to unlock the settings menu so that I can change all Px settings? When I am in settings menu it only lets me toggle between P01 and P02, all others appear to be locked.

[@TechTronic9000]

Some displays are locked with a password.

[@mariocr6457]

Can u show a video about the settings of the Display 830? thanks i have ado a20+

[@TechTronic9000]

The A20+ has the s866 display, have a look here kzbin.info/www/bejne/noTFda2retmkqKs

[@kamilhalimovic174]

Hi, I have problem. Can you tell me original settings? P01 > P16

[@TechTronic9000]

P01=1 P02=0 P03=36 P04=10 P05=10 P06=27.5 P07=1 P08=100 P09=0 P10=0 P11=2 P12=3 P13=12 P14=12 P15=29 P16=55

[@kamilhalimovic174]

Thank you very much

[@lalotorres8928]

@@TechTronic9000 thanks

[@omarfaisal5759]

Thank You 🌹

[@mrcoco3562]

Can i use this on others controller? And if i use the PAS for 25km and if i switch to throttle mode will it go faster den 25km above?

[@TechTronic9000]

If it uses similar controller / display, it might work.

[@reviewpebune4134]

Very good info

[@TechTronic9000]

Thank you for watching!

[@alaraul]

Hi! Can you please tell me, how to show the battery percentage on the Display?

[@TechTronic9000]

It is not possible, but you can see the exact battery voltage which is more accurate.

[@alaraul]

@@TechTronic9000 ok, thanks for the advice!

[@manp1039]

can you set regenerative braking with this display settings?

[@TechTronic9000]

No, and it's not supported by the motor as it has a way way clutch system so it doesn't put any drag when you are not using it thus has no braking either. This makes the bike very efficient and able to run like a normal non electric bike.

[@manp1039]

@@TechTronic9000 is that hub motor a geared hub motor or direct drive (gearless)?

[@TechTronic9000]

The D30C uses a geared motor.

[@Aleissa.Ibrahim]

Can you make a new video explaining all the settings? I have the same bike and the same system, but I accidentally changed the settings and it no longer works. The engine does not spin and the speed is not measured.😢

[@TechTronic9000]

I have already done that, have a look here kzbin.info/www/bejne/qYOzfISga8iUZqMsi=x-kk4ARpDCzh4Z0e

[@EicherCorp]

It works with the EU version?

[@TechTronic9000]

Yes

[@RLAtkins]

Our S830 Has a manual on Display and will not let the monitor work properly ??

[@TechTronic9000]

A (M) sign? That is motor error, check the cables first. If it's a (!) then it's usually a brake issues.

[@mayorgold8618]

I've got rhe same bike but the newest the problem seems to be it saying e09, throttle not working also i tried fixing it and i may have tangled with the menu settings , can some pls help😢

[@TechTronic9000]

Does the throttle go all the way back to zero when you release it?

[@sorataarisugawa3333]

I changed the wheel size and it works with 5 mode PAS. The display says 25 km/h but my gps tell me 36 km/h with 17 inch size entered in parameters

[@TechTronic9000]

I know what you did there 😆

[@hermanaditya2250]

How? To go 30km/h please share make video without buying extra stuff

[@sorataarisugawa3333]

@@hermanaditya2250 enter the parameters as video show it. Do the modification to get 5 PAS. Then go to p06 and change wheel size from 27.5 to 17 and that's all. But adding the accelerator is the best solution

[@diegolas1418]

Is it possible to reset the menu to the original settings?

[@TechTronic9000]

No, you just have to program each of them to the correct values.

[@diegolas1418]

@@TechTronic9000 I lent the bike to a friend, it worked regularly. When the bike returned to me, gear 3 didn't work, gear 2 went at 25km / h, gear 1 at 15km / h. Do you have any idea how this can be fixed?

[@TechTronic9000]

Gear 3 is for using the accelerator, probably it's switched to hybrid mode.

[@mauriziotavarnelli9811]

@@diegolas1418 I have same problem. Have you solved?

[@diegolas1418]

@@mauriziotavarnelli9811 Not entirely. I switched to the 5-gear mode and now the first gear goes at 15km/h, second gear to 20km/h and third gear to 25km/h, fourth and fifth gear dont' work. I don't understand what caused this but at least the bike works

[@news5644]

How to fix E09 Error ECU please? Thank a lot!

[@TechTronic9000]

It could be controller error or wiring problems.

[@SemVoicy2324]

What settings for po7

[@Djua.]

how can i connect my ado dece 300c to the ado app>?

[@TechTronic9000]

The dece300 doesn't have an app. The app is made for the new air 20, 28 and beast models.

[@Djua.]

oh ok, thank you for letting me know, much appreciated.@@TechTronic9000

[@Boyson66]

Hi , I received my bike and setting one was around 15kmh , setting two took it right up to 28kph, setting 3 didn’t do anything. I guess this was because second took it to its max. So I tried the above and immediately the battery started counting down from 100% , within 10 seconds the battery was showing o%. Totally flat. What have I done ?

[@TechTronic9000]

Do you have the throttle installed? Check the settings for battery, should be 36V, your might be set on 48V. Also fully charge the battery first time before use.