Engine Head XU10J4R Reassembling - PEUGEOT 406

[@25yerCBR400]

Руки оторвать такому мастеру!

[@ЕвгенийЛобах]

После таких мастеров говорят что Пежо плохая машина. А Пежо отличная машина. Просто обслуживают такие вот.

[@photocornerbandung1469]

kinclong lg Om mesinnya mantap

[@EgoShredder]

Great video, very informative! I have this exact same engine in two of my 306 2.0 XSi cars. One of them has a problem where it will cut out the power while driving for a few seconds, really abruptly like an emergency stop to walking pace and then a few seconds later will suddenly spring to life and take off fast. Car was driving to absolute perfection only weeks earlier. I've been advised to replace the crankshaft sensor wherever that is, but no guarantee this will fix the problem. I bought a couple of brand new genuine coil packs, and that fixed it 90% for a couple of days each time, then back to the old problem. Fuel pump tested and working fine, along with relay switch. Brand new spark plugs. Good battery in full working condition. Full brand new Bosal exhaust system. Air filter new.......oil filter, oil, fuel filter etc. Cooling pump is new along with the radiator. Diagnostics come up clean with no faults.

[@TheInspiring99]

Have you found a solution for your problem? I have the exact same issue with my engine on 406...

[@EgoShredder]

@@TheInspiring99 I still have that car in my driveway, but in Nov' 2016 I also went and bought another 306 of the same model. It had 52K miles on the clock but pealing clear coat and faded paintwork. Otherwise it runs very well after fixing up some minor things. The previous car though has plenty of life left in the engine and gearbox, and so it would be nice to get it working again at some point. It's been used as a donor car the past 4 years though.

[@ЕвгенийЛобах]

10:38 И снова здравствуйте. Корпус термостата на прокладку устанавливается. В видео опять старая прокладка и герметик. Зачем экономить на спичках ? Тюбик герметика стоит дороже той прокладки. Новая прокладка и затяжка нужным моментом - основа при сборке.

[@didikbalong2185]

Mas agung mantap

[@ЕвгенийЛобах]

8:23 Нет смысла в герметике на прокладку клапанной крышки. Если резинка новая (а она видно что новая), то нужно обезжирить поверхности и установить прокладку. Затянуть требуемым моментом. Там момент затяжки очень маленький, что-то около 10Нм (могу ошибаться). Болты М6, крышка пластиковая, прокладка резиновая. По молодости тоже и мазал и тянул до дури. Но если притягивать по заводской схеме и с правильным моментом, то и теч масло не будет. С годами (5 лет примерно) прокладка дубеет (твердеет). Поменять на новую (300 руб) и кататься дальше.

[@mazmazbiasa]

2:16 om itu bagian valve cover bawah memang tdk ada paking atau semacam gasketnya?

[@AGUNGH]

Ga ada om

[@mazmazbiasa]

itu pemasangannya perlu di torsi ga om?@@AGUNGH

[@tommyhand2747]

sedap...mesinnya baru lagi

[@catherinelisa9696]

Dear question if i want to increase the power of my engine gasoline xu5 (8 valve) 1580 cc with abore 83 mm and stroke 73...can i use a crankshaft of xu7 ( 8valve )with abore 83 mm and stroke 81 mm or can i use crankshaft xu9 (8 valve )with abore 83mm and stroke 88 mm ...This will be possible if the block block is similar...Do you think that is possible??

[@AGUNGH]

I think it is possible depend-on component designated, but you should make sure that it's similar.

[@JulioSavery]

Hi there , can you tell me the torque of main bearings , rods , cylinder head , camshaft .

[@adithenes9000]

Om share dong, kunci apa dan no brp saja yang dibutuhkan utk top oh sendiri di rumah? Berhubung low budget siapa tau saya bisa menyelesaikan sendiri. Saya ingin ganti packing... D9, kira2 langkah apa yang harus dilakukan, boleh minta tutorialnya 😁🙏

[@AGUNGH]

Untuk turun engine head lumayan banyak om kunci yang dibutuhin.

[@coulibalysouleymane9656]

Merci pour votre aide

[@catherinelisa9696]

Thanks for video

[@AGUNGH]

You're welcome friend. :-D

[@smockmimers353]

i had the same engine in my 406 but i had a problem it ran rough at idle when cold but when it warmed up ti ran just fine

[@AGUNGH]

Check Oil in your engine first.

[@smockmimers353]

@@AGUNGH i did the impossible with it i changed every fluid and filter changed all the gaskets redone all the wiring reprogrammed the ecu bought new valves and redone the seeds put new piston rings and timing belt and redone the timing abut 10 times new irradium spark plugs and still the same

[@artur.ribeiro.398]

BIG SMOKE FOR MEMES did you check the ignition coil ?

[@AGUNGH]

also check oil splash by open your oil cap when you run it in cold. it's probably your oil pump already weak, so when your engine run in cold oil need more time to go to your engine head that is why your engine ran rough when idle in cold until you engine head enough oil.

[@smockmimers353]

@@artur.ribeiro.398 i replaced it 4 times and the oil pressure is just fine

[@Ardian1899]

Btw, ga pake packing headnya om?

[@AGUNGH]

Pakai dong

[@danieljoshua7739]

Pake kunci nomor brp aj tuh Om, klo nurunin silinder head

[@Ardian1899]

Torsi baut2nya harus spesifik om?

[@AGUNGH]

Betul harus rata juga.

[@harrybagiotanumihardja4915]

bang bisa modifikasi electric fan dgn Thermo Switch jd fan nyaladi 85 drajat spt di Kamil Motor?

[@AGUNGH]

Bisa, beli modulnya yang adjustable aja nanti bisa diatur2 maunya fan on disuhu berapa derajad.

[@samostepanyan7125]

Where is timing metod?

[@AGUNGH]

do you mean timingbelt installation?

[@slimansiryou6391]

Super pinyin Farina 🇫🇷🇱🇷🤗😴

[@nauvalrizki4036]

Om saya pemain peugeot juga. Ini menambah power engga ya?

[@AGUNGH]

Bukan menambah power, tapi mengembalikan performa mendekati spek aslinya.

[@TonyLiriano-h7v]

Ando buscando el motor 406

[@blacknut2982]

wah ngerjain dimana ini Om?? btw pernah ke Kamil motor di daerah Ciputat gak Om?

[@AGUNGH]

Ngerakit di Engine Block Autowork Bintaro, kadang juga ke Kamil Motor itu deket rumah. Ga sering juga sih karena jarang ke bengkel, paling numpang ngopi aja Hehehehe...

[@akhmadrafaeljuliocharlos1491]

Lokasi domisil mana bang

[@JulioCruzSierra]

Como ponerlo a tienpo

[@paulouedraogo1522]

Comment traduire

[@WarlockMetalMan9]

Esta es la NO MANERA de ensamblar un moto....tapado en silicona...ni siquiera la deja fraguar una horita al menos....ese motor no durará mucho... se tapará en cualquier momento un conducto con silicona

[@iogann40]

Ролик вообще о чем?

[@ЕвгенийЛобах]

Ролик о том как не надо собирать двигатель. Руководства по ремонту с моментами затяжки и особенностями сборки у них походу нет. Не издавалось на их языке наверно.