Air disk brake pad change and adjustment

[@j81851]

As a mechanic or sorts for over 50 years and now teaching air brakes (drum s cam and disk) this is I will say one of the better videos I have seen. You are personable but better yet as good as that is you are knowledgeable. Too many YT "mechanics" teach the shirt tail way (this is how Bob, and Bill before him and Sam before him did it.... I think you get it) I like your authority, your knowledge and our speaking voice is smooth as butter. Great video would really like to use it for the bench segment prep for my guys working on Disk Air Brakes. BTW we work on garbage trucks and container roll offs so we get stinky nasty brakes often. Good job!

[@cmowers9]

You crack me up. I'm doing a pad replacement on school bus on Monday that goses down dirt roads Monday through Friday. The amount of caked on mud is of the scale.

[@bobhorsewood5689]

Good video. When I do a pad change the kit comes with new hardwaredware including the sheer adapters. I save the old ones just in case.

[@learndiesel528]

Great tip! you can never have to many shear adapters lol

[@royandrade2929]

Good info. Thanks

[@swiftzzxl4873]

Thank you for sharing your experience.dose the classic self brake adjustment work with disc brake as well or I should be do the same way you did on brake adjustments

[@dunnoyolo2238]

Were can i buy a sheer adapter ?

[@scottnicholson408]

One of the easiest disc brakes to work on.. Done a bunch of these. Also to check is the slides are worn out. Had one the bushings were worn out . The caliper would move up and down..

[@learndiesel528]

If you run across another one please take a video and send it to me. It will be good to get that information out. Les-

[@franmitch3589]

Great video

[@learndiesel528]

Thanks!

[@staceyhaynes7514]

How do you unloosed a rusted on shear adjustment

[@josevalencia6359]

Thank you

[@josevalencia6359]

Thank you god will pay you.

[@peterbivol2865]

Hey , what can be wrong i did 3 clicks when applying brake pedal it holds when parking brakes are set no brakes , even i tried 1 click still the same , the chambers are designed to hold on when using parking brakes non of the 4 tires is holding brakes when you pull the knob

[@143gurmukh]

everything usely seez in Canada weather on the table it' look really easy

[@baatarsandag5989]

thank you for video

[@learndiesel528]

You are welcome

[@El.locote.305]

how much does this divo system cost. the complete piece as you have it there

[@learndiesel528]

Im not sure I understand your question. Are you asking how much the mock up is??

[@El.locote.305]

Yes

[@jacquesmoolman8285]

Ohk i did everything that way but u can drive a bit then it locks up when i go to adjustment points they are tight i loose them 5 klinks drive about 2km then they bind again

[@JoseGarcia-uq6zr]

What is the adjustment on Bendix disc brakes that don’t click?

[@learndiesel528]

I am not sure never worked on those.

[@marioatrucking]

What are the best brake pads to get

[@learndiesel528]

Bendix

[@evildrmainstream...6767]

wish i could go back

[@krackerJT]

What if I keep breaking the sheer adapter. The brakes are aired up and released.

[@learndiesel528]

It sounds like the tappets may be sized. The adjuster should move in both directions with the brakes released.

[@rickykingi5191]

Would this apply to an FH 12 Volvo

[@julyszn]

It’s very similar however this is a benefit for tractor trailers.

[@timmychannel9645]

Where can I get that socket

[@learndiesel528]

What socket are you talking about?

[@joenero15]

They do have an 11 point socket for those calipers there are many companies that make them lisle is one of them

[@billrowland8350]

The washer is missing on the cotter pin side

[@wilmarcaldas3496]

How you replace the rotor??

[@learndiesel528]

You have to remove the wheel end.

[@chrisrodri2512]

Shear adapter

[@roadrescue8843]

Thauh - guess what. The facts please. We are not stupid.

[@roadrescue8843]

Ok ok ok ok ok ok. Move on. I see I see.

[@roadrescue8843]

Spit it out - uhh uhh

[@baltazarruiz6116]

Thank you