Air flow analysis on a racing car using Ansys Fluent tutorial Must Watch Kindly find the below link to download the hands on file funmechanical.b...
Пікірлер: 134
@Fabson_7 жыл бұрын
Nice tutorial! Thank you for post! Just a suggestion, you should make a tutorial explaining by your own words what's happening , like a step by step. Regards! =D
@Brosales14143 жыл бұрын
Hello my fluent is a newer version and seems to different from yours. Is there anyway to go back to using the older fluent setup?
@thawtar6825 жыл бұрын
With all due respect, I believe that the domain is too small. While being a very good tutorial, this might mislead beginners believe such a small domain is OK for their simulations. Especially when the outlet is too closed to the car, with not enough wake development. Even with the pressure outlet (zero gradient in terms of velocity), this domain is still too small.
@barantepe13355 жыл бұрын
Definitely you re right. You must increase the length of the enclosure about 20 times of car length near to pressure outlet.
@AG-cx1ug Жыл бұрын
Is the domain the box around the model at 3:10? If so, do you have to create it before you enter the model into ansys?
@piereligiodisante Жыл бұрын
Also, the ground should be against the wheels. Unless the car is meant to fly of course ahah
@bradhall72235 ай бұрын
@@piereligiodisante hahaha I was wondering this...
@homieknowme2235 жыл бұрын
22 ads in a 20:58 min video You must become rich overnight!
@nitroglicirin4 жыл бұрын
I will check this later on pc with adblock))
@semanasanta19964 жыл бұрын
Hi, I NEED HELP PLEASE. in my case, the vehicle is not solid but a shell/surface. I can't subtract the vehicle geometry from the enclosure. What could I do? Thanks!
@AG-cx1ug Жыл бұрын
Did you combine the solid and surface part of the car to create the box?
@solorider32966 жыл бұрын
excellent tutorial! but can you tell me how to decrease the size of the bubbles when animating the streamline? i found the bubbles are so big in my case. My case is also car aerodynamic just like in this tutorial, but i have no clue how to decrease the size of the bubbles when animating streamline.
@sonalbadode90312 жыл бұрын
Sir it's awesome tutorial sir can you tell me how to solve axisymmetric analysis on bottle I have tried but error comes .
@junwoolee38793 жыл бұрын
Can you tell me why you used the set ups that you did in this video?? I don't understand why you used initializing part and the methods part..?
@yariiijan82253 жыл бұрын
Is Ryzen 5 4600H with Nvidia Gtx 1650 good for Ansys, Solidworks, Openform, Hypermesh, Ansa? Any problem in that? Reply fast
@hudaibilgin84682 жыл бұрын
yes, im using same processor. It is quite good.
@imwaz36443 жыл бұрын
Hi With the recent iris xe graphics with the 11th gen i5 16gb ram compatible and sufficient with ansys for medium simulations?
@akashbhoi65045 жыл бұрын
I am using fluent on Wells turbine can you tell me how can I find pressure at any point after turbine...? This tutorial is very helpful thank you..
@yavuztankirik65533 жыл бұрын
thanks for the tutorial of yours first of all. Secondly, I have master degree thesis and wanna clear up it to you. Could you help me out for doing it in Anysis ? Wait for your support. Thanks a lot.
@mrrohan63963 жыл бұрын
Hello, Suppose we have a belt and pulley assembly. Can we vary the belt tension and analyse its effects on the pulley?
@김태욱-l3m7 жыл бұрын
hi thanks a lot for your video. can you make a video of fluid movement near the apartment?? i have a hard time with it.... i dont know how to make no slip condition on ground. also i dont know how to make enclosure 0 between gound and apartment. and i want to make other enclosure surface with free slip condition...... can you help me??
@zilongzhao25175 жыл бұрын
Awesome video! By the way, could you please make another video on how to draw the car geometry?
@humsjaved85783 жыл бұрын
Hi sir, im not able to select any of the body while doing enclosure. even if i click on generate in not able to do that. can you tell me any other way?
@sagarchaudhari87796 жыл бұрын
will you please help me in simulation of leakage flow due to pressure difference brtween two parallel plates, where one plate is stationary and other one is moving with DYNAMIC MESHING
@luisapenacrescioni21315 жыл бұрын
Hello! Nice video. If I am importing an assembly with different parts how can I use boolean in order to join them? Would I use unite instead of substract?
@mahmoudmuhammad75254 жыл бұрын
am not proffesional but in my opinion you can assemble them in other CAD program as solidrowks or inventor then import it as a one assembled part
@nitishpalanna87832 жыл бұрын
Yes! Works just as well
@valeriyaterenyuk20744 жыл бұрын
Is there a video where you make a car model? Did you build it with planes or bosses?
@CADDBS4 жыл бұрын
I will make a video for that
@valeriyaterenyuk20744 жыл бұрын
@@CADDBS And when will it be released?
@naifghazali78377 жыл бұрын
hi.i wanna ask..my flow analysis case involving cylic boundary counditions. is it same the way you do in this tutorial?
@CADDBS7 жыл бұрын
yes,u can also change the type of enclosure to cylinder if u want and continue with the same procedure....
@naifghazali78377 жыл бұрын
GlobalCAD hi sir, i really stuck and dont know who i want to ask. i really need your help. my case is to analyse flow between 2 identical buildings. can you make the video how to do that especially the part of the boundary conditions? 😓
@naifghazali78377 жыл бұрын
i can email you the detail if you are not clearly understand my case study...
@arwasheikh4137 жыл бұрын
For our simple project this is extremely helpful! Thanks!
@tannguyenvan14707 жыл бұрын
Goodmorning Sir. I would like to ask that you import area values in 8 ' 45 ' ' what is the value of the area. I don't understand this value Thankyou!
@Ja_Crispyyy11 ай бұрын
This was fantastic! Thank you so much for the help!
@vishnujayakumar12294 жыл бұрын
Sir is this sure the flow is laminar?
@kaysvideoseries96027 жыл бұрын
do you tutorial to make ocean wave using fluent??thank you..
@pranaykothari5713 жыл бұрын
How do you made model of car in which software
@evank1074 жыл бұрын
Hi, when trying to display pathlines, I have no option to select the interior model. Could you help?
@sonalbadode90312 жыл бұрын
Sir how to apply directional velocity in response spectrum analysis on spring suspension system
@LifesVoyager6 жыл бұрын
Clearly, a wind tunnel helps us to visualise airflow over a car. But, the objective is to improve airflow in the real world. In the real world, the air is more or less stationery, the road is stationery, and it's the car that moves - the inverse of the wind tunnel situation. Definitely different scenarios. May I ask - when using CFD for race car design, does the CFD software attempt to mimic the wind tunnel or the real world?
@PhilV2056 жыл бұрын
Reference frames?
@LifesVoyager6 жыл бұрын
@@PhilV205 ?
@majidrostami17775 жыл бұрын
respectfully you have misunderstood the principle of general Newtonian mechanics and also its application in fluid mechanics. about your comment " the inverse of the wind tunnel situation" : when a air is stationary and car is moving , the car has to move the neighboring air molecules of its front by the speed of itself, so it should carry the inertia forces due to changing velocity of molecules to speed of itself(Newton's second law) but in air tunnel wind , when air is moving at the desired supposed speed of car , when this moving air collude with the stationary car so it stops and the car has to bear the inertia force due to changing the speed of air from the desired to zero. the force in this situation is completely equal to previous one. above description is expressed loosely, forgive simplifications. finally i think you should understand the conception of engineering, it differs from being a scientist. the science seeking for perfect solution without any error and most of the time it is not possible but engineers looks for finding solution for the domain not for perfection. wind tunnel is answering well to real world engineering problems but has its limitation for super advanced topics . good luck a graduate of mechanical engineering
@PhilV2055 жыл бұрын
@@majidrostami1777 so in conclusion....reference frames.
@majidrostami17775 жыл бұрын
Yes actually you are right, but from the respond of dear Tristan I got that he is not familiar with the conception of reference frame, so I had an intention to express the de facto conception behind it.
@irfanameen56826 жыл бұрын
How to make this car and outer surface?Did you make any video on this type of tutorial?
@CADDBS6 жыл бұрын
Will surely make a video on that...
@irfanameen56826 жыл бұрын
Thanks bro I got it how to make.
@sundaramahalingamv42975 жыл бұрын
Hi Sir, During meshing the model it will generate it, But for Update, the Mesh to work in setup file - The Mesh is Not Update Kindly Help Me
@qaz75642 жыл бұрын
@globalCAD can i get access to the google drive link
@midhun2727 жыл бұрын
Nice video very helpful. could u tell me what is the minimum system configuration for ANSYS Fluent?
@CADDBS7 жыл бұрын
+shameer 8 gb ram nd i5 processor
@midhun2727 жыл бұрын
Thank you
@giovannigiorgio03 жыл бұрын
what is the different between plane and isosurface?
@tempebacem79187 жыл бұрын
any suggestion? car knuckle analysis
@SHREEKRISHNAMAHALINGAM5 жыл бұрын
Sir, I'm getting a message " Unable to update solution, Number of Iterations should be greater than zero"
@aniketagrawal91735 жыл бұрын
How u make car that has some thickness I created car but it have zero thickness and not work in ansys
@bobowofol6 жыл бұрын
Awesome tutorial! Thank you so much for sharing your knowledge. Helped me a lot!
@rajut62715 жыл бұрын
can you specify or suggest me pc configuration?
@TheUcyy6 жыл бұрын
Very helpful, learned a lot in the past using this
@OpenFOAMbasic5 жыл бұрын
What a wonderful tutorial. you made a good car. Thank you.
@adityaupadhayay99473 жыл бұрын
Thanks for this video. It was very helpful.
@sreeragpv7394 жыл бұрын
In my ansys, Relavance option is not shown.What to do?
@berkanyuksel19974 жыл бұрын
ı think you should define the areas(referance values part) solve from results section 'projected areas' becasuse model is 3d
@siong09186 жыл бұрын
where is the boolean operation command for ANSYS 19,urgent ! HELP!
@syntheticfiber73883 жыл бұрын
Thanks! Helped me with my assignment!
@rahimyarkhanupdates43926 жыл бұрын
sir can you execute Economizer in ansys fluent ? I have its igs file
@mukutvlog7 жыл бұрын
please upload tutorial for plasma actuator flow simulation
@lokesh619017 жыл бұрын
hello sir.. can you make a video on crash simulation of a an automobile ?
@CADDBS7 жыл бұрын
+The Big Bad Wolf sure dear ...
@chhsiao44004 жыл бұрын
03:28 relevance setting is no longer existed in 19.2, can anyone introduce a new way to solve that?
@mohamedeid70754 жыл бұрын
Did you find a solution ?
@hudaibilgin84682 жыл бұрын
I'm looking for it too.
@SerdarEker7 жыл бұрын
it is very useful to start with.. thanks for the effort
@CADDBS7 жыл бұрын
+Serdar Eker thanks and in future we will be adding more videos related to this.....
@rubengonzalez59217 жыл бұрын
Very good tutorial....but your mouse run like as laser beam......
@mustafayusufgirgin92213 жыл бұрын
Thanks for your help :) Great video dude
@oumsaadaboaleuon30264 жыл бұрын
Hi, I need drown car by CFD .
@ALYSSONHENRIQUERUBLESPERGERDEA Жыл бұрын
Very helpful! Thank you sir!
@aliyigitakaln25827 жыл бұрын
what about ship in calm water?
@nadimpallivenukumar86906 жыл бұрын
please send abstract and documentation for this video demonstrated
@mahmoodhasan91644 жыл бұрын
I think the height of the vehicle must be like the real because it is very important factor
@varunt68464 жыл бұрын
hi, guys, can anyone help me in solving this " how can I create a single body geometry in Design Modeler since I have 38parts and bodies of my imported geometry". Thanks in advance
@MohammedKhantheacademician4 жыл бұрын
Hi.. You need to modify the geometry in the design software itself.
@MohammedKhantheacademician4 жыл бұрын
what is the geometry? you need to have the geometry properly connected
@peednas1das6 жыл бұрын
can anyone tell me how can i calcuate drag and lift?
@BRIJESHKUMAR-sk1ex3 жыл бұрын
how to read that design is good or not, there is no such good video, only procedure to obtain results are there.
@willcoomes29532 жыл бұрын
good tutorial, but ads pop up every minute, makes it very annoying to watch
@EngHub96 жыл бұрын
Nice Video.It's Really Helpful.
@CADDBS6 жыл бұрын
Thanks happy to help😊
@deepakprabhus48335 жыл бұрын
Kindly Upload the CAD file for that model
@GauravKumar-zn5gz5 жыл бұрын
Thank you sir .. it is very helpful ☺️
@muhammetklnc29083 жыл бұрын
hocam videonda ses yok ama herkese hitap ediyo olsun .
@manmohankonakalla82977 жыл бұрын
can you give me the validation data of it
@kundanlamsal2 жыл бұрын
How to solve convergence error?
@СеменМаломониторов5 жыл бұрын
Maybe it is possible somehow locate external boundaries more close to object, but it is actually impossible.. XD
@TheSzrMedia3 жыл бұрын
Hocam elinize sağlık
@tabishakhlaque48605 жыл бұрын
good for basics but not for accurate solution
@Oscar-qf7lf3 жыл бұрын
The mesh part is wrong... inflation is needed!
@psmsound70113 жыл бұрын
Nice explanation 🙏
@CADDBS3 жыл бұрын
Thanks ☺️
@praveenoswal76167 жыл бұрын
Why isn't atmospheric pressure considered?
@Madmetroid997 жыл бұрын
praveen oswal Ansys works with relative pressures, not absolutes ones. So PRES=0 means atmospheric pressure and PRES=-1atm means absolute void. (Pardon my english)
@celiacedeno98074 жыл бұрын
thank you so much, I am so grateful!!!!
@tayvan87047 жыл бұрын
18.1 how do?
@josephakhil56585 жыл бұрын
tank U its very help full
@muhammadauzan99514 жыл бұрын
This video make me want to buy youtube premium. Thankyou anyways
@hakhil68275 жыл бұрын
Excellent tutorial.
@abhiksarkar8694 жыл бұрын
amazing video.. thank you
@cyrilsiby22022 жыл бұрын
So much ads are coming each time I pause the video