Showing you how i repaired the air leak in the valve in the bottleneck of my FX carbon fiber airtank
Пікірлер: 131
@OH8STN Жыл бұрын
Catching up on all your maverick videos. Your effort is greatly appreciated
@Airbuks Жыл бұрын
Thx buddy
@donaldlemens92543 жыл бұрын
If anyone uses or continue to use the Huma quick fill adapter, you will have this same problem over and over. They now send a restrictor screw to use But it won't work either, it may work once or twice. Using the Huma blows the valve seat out of its seat, sometimes no damage to oring just reseat but sometimes the same as the video. When the bottle is screwed on the gun for filling the valve is pushed open allowing easy air transfer in either direction, using the Huma only high pressure air has the force the valve open thus unseating the valve seat. Bestfittings is working on one that will work simulating as when on the gun.
@450353 жыл бұрын
Out standing shipmate. press on.
@astawfik303 жыл бұрын
When I did mine the hardest part was to remove the valve. Which was Loctited, with black Loctite. I think you should mention this and would be better if you will show how to remove the valve without a purpose-made tool. Apart from these, great video as usual.
@Airbuks3 жыл бұрын
Hi , my valve had no loctide on it , I have heard from others that there was loctide on there’s aswel , strange there is no need for loctide on it 🤔 I first tried to remove it without the tool but I say quickly that I couldn’t open it without damaging it or leaving marks on it .
@hotchihuahua15463 жыл бұрын
Good point , you are dealing with carbon fiber , you can’t heat it without possibly compromising the carbon tank !
@berademir104 ай бұрын
How to bleed out the air entirely in the tank? Without shooting ofc. Good video btw.
@AntonioLopez-jg1gd3 жыл бұрын
Hola soy Antonio español Me he suscrito a tu canal porque me parece muy interesante Soy propietario de una impact M3 POR FAVOR LOS SUBTÍTULOS EN ESPAÑOL GRACIAS
@scottmichael37452 жыл бұрын
Thank you! That's Exactly what I needed!
@Airbuks2 жыл бұрын
Great 👍🏻
@Jeeper1378 Жыл бұрын
I just starting noticing a small leak when the bottle is attached.. any ideas ? Two bottles so its not the bottles o-ring.
@Airbuks Жыл бұрын
Replied in your othe comment
@junardburigsay78463 жыл бұрын
What's the simplest way to bleed the air if the bottle has pressure in it
@Airbuks3 жыл бұрын
Option 1 :Huma air sells adapter to fill a CF bottle but you can also use it to bleed the bottle Option 2: saber tactical sells a kit to bleed and remove the valve Option 3 : and the most cheap one , find a bold that can be threaded into the neck slightly file it down one one side so the air can escape slowly . Gently thread it on so the valve pushes open and let the air escape slowly. REMEMBER BEING SAFE , MAKING A TOOL LIKE THIS AND USING IT IS AT YOUR OWN RISK
@snipertuban933 жыл бұрын
Good
@chefrenty9155 Жыл бұрын
Nice video, wel explained and very helpfull as allways 👍. May I ask,what do you use for lubrication of the o-rings? Will Ballistol do the job or is any silicone oil better? Thanks in advance.
@Airbuks Жыл бұрын
Thx for the support, I use silicon olie from Huma Air .
@chefrenty9155 Жыл бұрын
@@AirbuksWat leuk, ik zag dat u mijn Zuiderbuur bent, ik kreeg al een idee vanwege de 'olie' ... 😊
@Airbuks Жыл бұрын
@@chefrenty9155 😉👍👊
@muhammadullahchowdhury9296 Жыл бұрын
Thank you for your video.
@Airbuks Жыл бұрын
👊
@MyBuster007 Жыл бұрын
what is the size of the o ring which seal on to the gun?
@Airbuks Жыл бұрын
You can find that on the diagrams on the FX website under the support page 😉
@derivas0073 жыл бұрын
thumbs up like always on each you video to help you!
@Airbuks3 жыл бұрын
Thx 🙏🏻
@franciscocarvalho24243 жыл бұрын
Parabéns like garantido sempre
@robertfeddeler5508Ай бұрын
There's lots of videos showing the rebuild of the valve but none show replacing the Oring that seals it to the rifle.
@airshootist3 жыл бұрын
Wonderful video, helped me a lot! Thanks, Airbuks!
@Acutus33993 жыл бұрын
Very cool to see how these things work! Thanks for the demo!
@Airbuks3 жыл бұрын
Thx 🙏🏻
@DuongPham-ip4ln3 жыл бұрын
where can i buy that bottle of carbon
@Airbuks3 жыл бұрын
At Krale Schietsport or Huma air
@numizaairguns13733 жыл бұрын
Good idea. I like your tool
@Airbuks3 жыл бұрын
Thx 👍
@monkyshine55433 жыл бұрын
Good training for me thanks.
@Airbuks3 жыл бұрын
Thx
@MasonStormSunny3 жыл бұрын
What is the total length of Impact compact with Donny's silencer?
@franckbecanfayeboue48773 жыл бұрын
Great Video. Is it recommanded to put some loctite on the threads going to the inside of the cf tank, or shall we just snug it up?
@Airbuks3 жыл бұрын
Thx , mine didn’t have any loctide on it from the factory. So I don’t think it’s needed . There is a oring in the neck to seal it and the pressure on the inside will make it impossible to unscrew.
@hotchihuahua15463 жыл бұрын
I don’t see the point of loctite if an o-ring is used to seal the air , if anything anti- seize might be better ! Tanks unlike mechanical moving parts on nuts and bolts should not require loctite .
@thakurnileshprakashsinghАй бұрын
Thank you very much for make it easy for us.
@PETRAKOV1 Жыл бұрын
How u degas the bottle? Do you have tool for that wich comming with the rifle in the box?
@Airbuks Жыл бұрын
There is no tool that comes with the gun in the box 📦 but there are a few tool available like a bottle adapter from Huma that you can use or the bottle degassing kit from Saber tactical
@PETRAKOV1 Жыл бұрын
@@Airbuks What is the tickness of the metal sheed wich u use to make the tool for removinge the valve
@Airbuks Жыл бұрын
@@PETRAKOV1 I believe it’s 5mm 🤔 but i am using the kit from saber tactical lately 😉
@PETRAKOV1 Жыл бұрын
@@Airbuks I have freind wich can cut this on laser for me free. No way to pay 60-70 euro for one "Kit" to move the valve to outher bottel just one time :D
@marioreyes5483 жыл бұрын
Excellent Video, where do i can buy the O ring that you change? Do you know wich number of part is ir? Thanks
@Airbuks3 жыл бұрын
Thx 👍🏻 you can by these orings anywhere I guess , it’s a very common item/size . The correct size is mentioned in the video , I don’t know it by heart 😉
@DeReK-og4om3 жыл бұрын
Bonjour , taille des orings ?
@Airbuks3 жыл бұрын
Hi , English? All the oring sizes are specified on the support page of FX Airguns
@KnowsleyVerminControl2 жыл бұрын
I am having trouble replacing the O'ring inside the bottle valve, is there a trick to it?
@Airbuks2 жыл бұрын
Not really a trick , some patients and a blunt tool to manipulate it in place 🤷♂️
@KnowsleyVerminControl2 жыл бұрын
@@Airbuks it is really difficult to replace i have been trying for so long
@Airbuks2 жыл бұрын
@@KnowsleyVerminControl push it inward down so you put one side of the oring in the groove , hold it in the groove with a blunt object ( Allen key for instance) the use another Allen key and push the rest of te oring in the groove
@8139463 жыл бұрын
Its another oring inside the treaded part of valve that connects to impact why didn't you show that its the hardest oring to replace on CF bottle
@Airbuks3 жыл бұрын
I didn’t show that because mine didn’t fail there , but with a dental pick it’s not that hard to do . Just some patience 😬
@GiancarloDiChiara3 жыл бұрын
Magic Carbon
@tonydavisbusiness Жыл бұрын
How many cc is the airtank?
@Airbuks Жыл бұрын
300cc
@martdod3 жыл бұрын
Just the video I’ve been needing. Thank you!
@Airbuks3 жыл бұрын
Hope it helps 🤞🏻 good luck 🍀
@snipersnipe42593 жыл бұрын
@@Airbuks can u plz tell the check valve O ring n valve part no I need a complete set for spare
@Airbuks3 жыл бұрын
@@snipersnipe4259 this I don’t know, is it not specified on the drawings that are in the FX website?
@abitoutside3 жыл бұрын
Great video buddy, thanks for the info.
@Airbuks3 жыл бұрын
You’re welcome thx 🙏🏻
@TheAtherstone3 жыл бұрын
What a great video the camera work on this is very simple very clean very sharp you show everything so well.and you still get a dickhead who puts the thumb down.I mean seriously he must be another KZbinr because your video is great and very intuitive.anyway supercool. 😝👅👊🏼👌🏼
@Airbuks3 жыл бұрын
Thx for the support mate , there will always be someone who disagrees 😉👊🏼
@TheAtherstone3 жыл бұрын
I can only put this down to somebody a bit dumb. Or just jealous 🥴🙄😂
@shahriar9073 жыл бұрын
Very teachable and helpful video. Thank u so much.
@Airbuks3 жыл бұрын
You’re welcome 👍
@bstiemnangsanbaythanhhoa58043 жыл бұрын
How much this bottle
@hotchihuahua15463 жыл бұрын
The PCP world is growing very fast , I know first hand just with volume & Tire pressure in tires with up to 120 psi how deadly they can be and can kill ! we are dealing with bottles in the 4,500 psi range in the PCP world , it’s no longer handled through scuba shops who know how to test and fill these air containers ! Every time I fill one of my portable tanks I am aware of how dangerous it can be ! It’s so easy to overfill at a higher pressure while transferring from a 4500 psi compressor into a 3000 or 3500 psi PCP tank ! Enjoy the sport but realize what you are dealing with , it’s just like a loaded gun with the safety off ! Nice video and repair tool you made ! 👍
@ehsansarmeydani3213 жыл бұрын
Were you going to make a clip or an overview of the Marvik 22 caliber tuning with an 18 or 25 pellet? what happened?
@1352opd Жыл бұрын
where can i order the o ring at 4 1/2 x 1/2 nor 70
@Airbuks Жыл бұрын
Sometimes you can find boxes at your local hardware shop or your local dive shop might have them aswel . If that is no option there are many online shops that sell orings
@skalliwag27662 ай бұрын
Thank you
@wernerherrmann3 жыл бұрын
Thank you. great video. I have a leak from the breather hole near the safety. I know the origin is the reg. I have replaced all the o-rings. And recently purchased a service kit and replaced the delrin rod and adjuster screw. Still it leaks from the breather. Any advice? Thank you
@davidhill46952 жыл бұрын
very useful information ..nice clear video
@Airbuks2 жыл бұрын
Thx , hope it helped
@archangels4you5933 жыл бұрын
Great Videos as always... Thanks for sharing !!!
@Airbuks3 жыл бұрын
Thx
@sergeantmao80173 жыл бұрын
? For you man, I have issues with top valve connection o rings blown out how do I put a new one in I have no clue where it suppose too sit in.
@Airbuks3 жыл бұрын
Can you explain more detailed or mail me some pictures ( airbuks@icloud.com )
@sergeantmao80173 жыл бұрын
What I’m trying too address is that trying too see where does the O rings seat in. Reason I ask that I took it off and try too replaced it but forgotten where it supposed too seated in. This is referring too bottle thread into the gun it self. O ring got blown off and leak air. If you can help me out I would appreciated it. Again valve bottle thread o ring installation location. If you have clear pictures would be awesome
@Airbuks3 жыл бұрын
@@sergeantmao8017 so if I get it correct , you need to place the oring in the bottle valve part that screw into the gun ? You can check the diagrams and oring sizes on the FX support website
@sergeantmao80173 жыл бұрын
Yes correct. I had look on FX couldn’t track it down
@Airbuks3 жыл бұрын
@@sergeantmao8017 part number one is what you mean think fxairguns.com/wp-content/uploads/2020/03/airbottle-200326.pdf
@martdod3 жыл бұрын
The valve seat is flat on on side and cupped on the other. Would you please explain which way the valve seat goes back into the valve?
@bashImpact5 ай бұрын
good one.
@bg31603 жыл бұрын
my bottle is leaking. Thank you!
@Airbuks3 жыл бұрын
Hope the video can help to fix it 🤞🏻
@danieldawe2163 жыл бұрын
Do you ever play around with the edgun leshiy 2? Would love to see you mod one of them, like you did with the dreamline tac compact. That was wicked 👍
@Airbuks3 жыл бұрын
Maybe that wil still come in the future. I would love to have a leshiy 2 👌🏻
@danieldawe2163 жыл бұрын
@@Airbuks I've just put my order in with Francisco for the 250mm version. I think you would enjoy testing out the power jets and regulator tuning. Not to mention all the different mods you have for them.😎
@Airbuks3 жыл бұрын
@@danieldawe216 I know 😔 , I will have to speak with Francisco again. But congratulations on you purchase 👍 enjoy the leshiy 2
@nico-max3 жыл бұрын
Very good explain man 👍🍷
@Airbuks3 жыл бұрын
Thx
@severinorobsondamo45773 жыл бұрын
Top essa dica
@jaypeemagno70443 жыл бұрын
👌👍😍❤️
@tedsell14552 жыл бұрын
Great video Thanks
@Airbuks2 жыл бұрын
👍 thx
@johnjingleheimer69923 жыл бұрын
Installed a power plenum on my impact now air leaks rapidly out of the weep hole fx says the regulator orings need to be re-seated but I did what they said and no such luck. Any ideas ? feal like giving up on this gun and cutting my losses
@wernerherrmann3 жыл бұрын
I have the same problem. I even got a service kit and replaced the rod and adjuster. Still leaking through that breather hole.
@Airbuks3 жыл бұрын
Hi guys , sad to hear you’re experiencing this issue. Probably you have done this but I am asking it anyway to eliminate some options. 1. When you took the regulator completely out , did you make sure that everything and every surface was super clean before putting it back ? 2. Did you scratch any of the oring surfaces when removing the old orings? 3. Did you also replace the oring down in the regular hole ? Very difficult one to acces and easy to scratch that surface. You need a good pick to poke in the oring and manoeuvre it out ( like dokter bibber game 😉) 4. Did you lube all the orings when putting the new ones one ?
@wernerherrmann3 жыл бұрын
@@Airbuks Thank you for the ideas. I'll strip it again a little later and check for any dirt inside. I'll wash it out with 99%Alcohol.
@Airbuks3 жыл бұрын
Make sure the alcohol is complete vaporized before assembling as it’s not so kind on orings . I recommend not using anything with alcohol, ballistol is much better for airgun use
@wernerherrmann3 жыл бұрын
@@Airbuks Thank you. Well after a lenghty clean, the spit test now reveals no leak, But test will be tomorrow morning. Usually after a few hours, the leak gets bad