I had the exact same problems as you...everything. Thank you for the video. Everything is all good.
@craftyguyeric Жыл бұрын
After taking the belt off, loosen the bottom bolt, take out the top bolt completely, pull the alternator fwd. You'll be able to remove the cable, plus you'll have better access to the bottom bolt. When putting the alternator in, go in reverse. With the alternator fwd on the bracket, you can easily re-insert the bottom bolt, tighten to the point where it almost tight, but you can still push the alternator up on the bracket. Put cables back in, push fwd and bolt the top, then tighten the bottom.
@louiekush2742Ай бұрын
Glad I found this video. My alternator is going bad. All dash lights are flickering. Going to change it myself but sadly I don’t have a voltage tester
@stevenhoang4336Ай бұрын
harbor freight has one for a few bucks.
@sizzelot2 жыл бұрын
Thanks for the video. Almost gave up trying to get the alternator out till I saw your screw driver prying on the bottom method. I squirted a little bit of WD-40 on each side of the bolt hole and moved the alternator back and forth several times to work the WD-40 into friction area. It then came right out by prying with the screwdriver and moving alternator back and forth.
@chrisb156793 ай бұрын
To save you time and headache, remove the condensor fan (fan directly across from alternator) It's held on by 2 10m bolts up top and 1 plug down by the frount mount. Remove the fan and you have waaay more clearance and space to work with.
@joshmnky3 жыл бұрын
Just fixed mine today. Only video I watched. Thanks for the help!
@stevenhoang43363 жыл бұрын
Im glad i could help
@gyamane53152 жыл бұрын
Thank you for your video! I have a 2010 Acura TSX and had to change my alternator today as preventative maintenance. AAA said it needs to be replaced though I wasn't certain since it seemed to be still good after some testing. Since I had 150k miles on my car, I decided to swap it out. I ran into the same problems as you. It took me more than 45 minutes to pry the alternator out after removing the two bolts holding it to the engine. But after watching you video, I was able to find the location to pry. After being able to pry it out after probably 2 hours, everything else went smoothly. Thank you again! Your video saved me and many others I am certain!
@stevenhoang43362 жыл бұрын
I am glad the video helps.
@tsunamizc Жыл бұрын
Thanks bro. Wish I had watched your video prior, could have saved myself some time. Getting the alternator out was also very difficult for me as well, lots of wiggling lol
@fkzego2 жыл бұрын
I am about to do this as my 09 TSX alternator died while driving. Great video and definitely this video will help.
@M3rKPirate2 жыл бұрын
You my cousin 2 Steve, just ripped my alternator out in 30 mins in my 2010. Thanks dawg
@AbideUS2 жыл бұрын
Use some Water Displacement, 40th Formula to get the alternator out of the bracket it helps a ton.
@evyyunga3 жыл бұрын
My Acura TSX alternator and battery died and this was useful deal !!
@AbideUS2 жыл бұрын
You earned a like and subscriber, helped a lot.
@Jaspereyne3 жыл бұрын
Good job. To have some more space you can lift out the coolant overflow tank and put it aside.
@mobrule86102 жыл бұрын
On a 6 cylinder 3.5 you have to do a lot of different stuff. You have to take the bracket off that holds the cable that runs to the alternator hook up. There's some weird hook up that runs through this cable patch that hooks up to the engine under the alternator, but the cable is connected to the back of the alternator. You have to take that off. Then you have to make sure you take both of those cowlings off, those black covers that cover the radiator and the side where the radiator fluid is and the window cleaner fluid. Then the little bottle that holds the radiator fluid, you have to take it off and take the bracket off that holds it in place. Then you can orient the alternator so you can slide it out of there. And remember exactly how you slid it out because that's the same position you have to use to put it back in there. Remember to start from the bottom when reinstalling the serpentine belt. If you are replacing the alternator I would go ahead and replace the belt.
@sak31552 жыл бұрын
Why there no videos for the V6! How did you get to the bolt that's directly in front of the tensioner?? I'm watching these videos of the 4 bangers for reference and they looked easy enough to do but I'm on my 5th hour!😭
@Arnsbabie Жыл бұрын
I've been tugging on this alternator for an hour!! Still not coming out! 2010 Acura TSX. What can I do!
@NINO0116742 жыл бұрын
Great video thank ..!
@reggiemillz22r504 жыл бұрын
I have the same problem trying to get it out and do not understand how you got that screwdriver under the alternator to get it out
@stevenhoang43363 жыл бұрын
Use a short flat screwdriver cuz there is not a lot of room down there
@LuisGarcia-wr6xn4 жыл бұрын
I have the same problem and thank you so much for your video I like it and I’m going to do it by myself too thank so much bro 💪💪
@stevenhoang43363 жыл бұрын
Hope the video helps
@LuisGarcia-wr6xn3 жыл бұрын
I already changed it and your video helped me a lot
@Arnsbabie Жыл бұрын
Should i attempt to pry from underneath the car or is the spot reachable from the top? Your video is very helpful but i am still trying to get it out
@rhandley10004 ай бұрын
People who say you need WD-40 or some kind of grease to get it out or correct. It was not budging for me for 30 minutes. I applied a little white lithium grease and it was out in a minute
@louisfredgagnon3 жыл бұрын
I'll be replacing mine eventually alongside the idler pulley, tensioner... oh and just for your sake, get a 24f battery and gently put the 51r in the bin. Never mind if you live in the south, but cca power and battery juice is better since swapped mine. Ez and tons of vids on the net!
@DarionNexus3 жыл бұрын
I can't get the bottom bolt
@marshallrandall52683 жыл бұрын
You my cousin steve
@ezzz84322 жыл бұрын
It’s called a pry bar bro. So you can lossing it
@jmartinez54633 жыл бұрын
Man I can’t see where’s the bolt below the alternator
@stevenhoang43363 жыл бұрын
Yeah, you cant really see it. What i did was sticking my phone camera down there and took a picture then base on that picture regarding to the location of the bolt, it stuck my finger down there to feel it