Love how they took a 2$ tea tong, called it a diff dunker and changed the price tag to 7$ 🤣
@stefanschuchardt5734 Жыл бұрын
No, its clearly a diff dunker! Dont you see it?
@swealer11 ай бұрын
Just wanted to write the same😅. I bought my tea thingi @ the edeka hier in germany in the 1€ box-stands😊
@joefussy114 жыл бұрын
😂😂Thats a tea strainer
@crimsonfancy4 жыл бұрын
do all three? www.amazon.com/Strainer-Mulling-Stainless-Perfect-ARTIST/dp/B07FZP5YFB/ref=sr_1_6?keywords=tea+strainer&qid=1581915911&sr=8-6
@deltazero37964 жыл бұрын
Definetely XDD
@patriotrob70664 жыл бұрын
We used those for umm our powdered sugar yeah that's it powdered sugar!!😄
@proz71ful194 жыл бұрын
It can’t be.. tea strainers are wayy cheaper ....... 😂
@jackdurden4663 жыл бұрын
Exactly what I said!!
@rcwck4 жыл бұрын
I always put diff fluid in after the installation of the sun gear then very slowly insert the spiders and cross shafts. This insures better fluid distribution especially with higher viscosity fluids. It also speeds up the flowing into and bubble waiting period. You can dab out excess fluid with q-tips if level is too high. I do my shocks in a similar manner.
@troyflanagan42373 жыл бұрын
I clean my shocks with wet rag make sure they are Dry then blow the hole inside of Truck ot with Dustbuster and spray the shocks front and back wheels to make sure they are cleaned and dusted out Excessive dirt then spray them with Dw40 or LuBRICANT SILICONE AND AND ALSO SPRAY AND CLEAN ALL THE ARMS FRONT AND BACK USE SAME PRODUCTS FOR ARMS TO 3 PRODUCTS I USE TO CLEAN MY VECLICE AFTER DIRT RUNS
@troyflanagan42373 жыл бұрын
Now i bought s product Called simple green u can spray it Everywhere on your Truck or rc car but blow the dust out first i use product Called Air Duster then i will spray the New Simple Greem product let it sit for 5 minutes. Wipe it down with a dry rag wait until it fully dries then spray Dw 40 om truck
@drjavogel4 жыл бұрын
Brett, you really are gifted with creating these presentations. Very clear, concise and valuable info. I appreciate your effort. And your table bongos rock!
@DashzRight3 жыл бұрын
He really is, he just doesnt try to sell you stuff, there is a lot of genuine value to their videos.
@namn1234 жыл бұрын
I usually use my "diff dunker" for tee...
@skagerstrom4 жыл бұрын
Minns när DJMedic visade upp en fancy multiskruvmejsel från Duratrax. Nu finns den för 20 dollar, men har för mig att den var närmare 30 då. Vad var det? Biltema 71-531 :P
@fromfin904 жыл бұрын
Good to know, i bought a secondhand traxxas summit and found its front diff shattered internally, so i am waiting for new parts, then fill it and rock it
@jdsrcs80614 жыл бұрын
Cool vid B!!!! Tools tools tools!!! You can never have enough tools!!!
@LegendaryRc4 жыл бұрын
You are so right
@AMain_Hobbies4 жыл бұрын
Never! It just isn't possible. Tools & R/C's ;) -Brett
@xd_gangster6934 жыл бұрын
instead of nitro spray or whatever that is called you can use break cleaner.
@DudaZachary2 жыл бұрын
This was the comment I was looking for! Thanks
@malinhiles10 ай бұрын
Genuine question. Why wait for the air bubbles to come out of the diff fluid, if the manufacturer doesn't have reccomend completely filling (overfilling) the diff housing anyway? It seems to me that if we aren't filling it all the way, there's going to be air in the housing anyway that will mix with the fluid when the car is running
@nachtfuchs3219 ай бұрын
I just started with RC Cars, this is the best rc channel to me. So much information and tips, greatly presented, I get exactly what I needed to know in every video so far and everything without headache at the end of the video because there's no in-your-face-screaming-chaos-modern-social-media-attitude ^^ thanks a lot, I'm gonna clean my diffs now.
@surfside753 жыл бұрын
This guy is so great, I could listen to him explaining how to clean a toilet.. I'd be here😂👍 -great info I was searching for.
@DOUGandNIKI5 ай бұрын
I have an HBX 2997a and it seems like more of my power has switched to the forward wheels over time. Does that sound like a Differential issue?
@DudaZachary2 жыл бұрын
How about regular brake cleaner instead of the fancy and probably overpriced nitro cleaner?
@homepage924 жыл бұрын
This was rally helpful, I just new in hobbygrade rc.
@tlfbshti3644 жыл бұрын
Lookin DAPPER again today Brett!! Great vid as always: I was worried you wouldn't use a solvent cleaner, and I think it's absolutely necessary, so I'm glad to see you went for the full "proper" rebuild here. Still, I would've like to see you recommend a full tear down and soaking the parts in Naptha or similar, as it gets rid of all the extra dirt around those sealing edges...Cheers fella!
@AMain_Hobbies4 жыл бұрын
Yeah we'd like to give it a shot. I sadly hadn't heard of it before reading the diff dunker instructions but that looks like the way to go. I imagine it's available at a hardware store, maybe Home Depot in the states? -Brett
@tlfbshti3644 жыл бұрын
@@AMain_Hobbies absolutely! I get NAPTHA from my local hardware store, so I'd imagine it's readily available almost anywhere!!
@EXTREMERC4164 жыл бұрын
Me: just rebuilded my whole car. Me: realises that i did not wait too mcuh to release the air bubbles Me: wanting to do everything right Me: massive headache
@crimsonfancy4 жыл бұрын
Not mentioned but a heat gun also changes viscosity in the diff. Use a heat gun to remove old fluid and use it again to settle the new fluid. Waiting can somewhat be bypassed imo. Good show for sure though. Every time I watch a diff video I gain knowledge and confidence. Arrma 6s getting more and more love outside the bubble too... more than ever now in 2020. 🥇
@EXTREMERC4164 жыл бұрын
The amount of paper i use is insane i cant remove all of the old fluid outit gets stuck in forners i even use a flat ehad screw driver to help me out i dont like really using like brake cleaner i have a little leak on my diffs because my clear grease turned milky white after testing its oil mixed with grease im going to stay with the factory gaskets for now on migth also contributed to my diff getting worn pretty quickly
@adamwhite58322 жыл бұрын
i got an arrma outcast 6s from facebook marketplace a while back. went to service the diffs and there was NO diff fluid in there😂 always check your used vehicles guys, don’t trust other people’s work.
@MapdecАй бұрын
Every Brit laughing at the diff dunker tea strainer. 😂😂
@navelaviator184 ай бұрын
What if your car doesn't state a recommended oil fill level in the instruction manual? I have a kyosho DBX VE 2.0. Based on the instructions, they call for grease, not oil. I have heard good things about going with silicon oil over grease but i don't know how much to put in. Any help from anyone would be greatly appreciated! Thanks!
@maddyschoonmusic7423 жыл бұрын
Love the vids! Also, love that my main man seems to have a perpetual cold as he couldn’t sound more congested. 🤌😂🤘😎👍🤙
@gunsandcommissions4 жыл бұрын
I miss working on my rcs 😔
@mcgruff4244 жыл бұрын
Love you're videos! Very entertaining and educational thanks you've helped me from making some huge RC mistakes!!! #rcnoob
@AMain_Hobbies4 жыл бұрын
Glad we could help Trace! Let us know if you have any R/C questions and thanks for watching. -Brett
@user-vb3dg3pb6s Жыл бұрын
Google review, we all know what diffs do and how they 4 , but please make your reviews shorter and straight to the point as in each specific topic. Diffs - straight to diffs
@thevix12344 жыл бұрын
Brett and the intro music are the best! Keep it up. 😃👍
@richardcorfield99263 жыл бұрын
It's a tea strainer!! (The "Diff Dunker")
@araszues Жыл бұрын
Personally. I prefer to smoke cigarettes when I spray any kind of combustible fluids. But for sAfety reasons. You should not.
@AMain_Hobbies Жыл бұрын
You made me laugh out loud, thank you. -Brett
@GreatLakesRC4 жыл бұрын
Nice video Brett 👍 I use PT racing diff clean. It breaks down the silicone with thinner silicone. No brake cleaner necessary.
@AMain_Hobbies4 жыл бұрын
Awh man, great tip! Sadly, I've never heard of it but it looks good and the price is right. We're going to look into this. -Brett
@GreatLakesRC4 жыл бұрын
@@AMain_Hobbies I think it would sell well 😉
@AMain_Hobbies4 жыл бұрын
@@GreatLakesRC Me too! -Brett
@zachulatowski43993 ай бұрын
I used silicon ear plugs and its about 20 million weight fluid and its soild so no air get trapped when you pack it down
@2shoestoo4 жыл бұрын
And if you up the weight in the center diff what effect does it have on the front/rear diffs? What is the effect if you up or lower the diff weight in the front/rear diffs? A lot of questions a lot of RC car people have. I don’t think you addressed this in your explanation. Can someone with experience in this chime in and help educate us. Thank you.
@paulclancy24044 жыл бұрын
Thicker the oil , more wheels work together instead of giving and causing one wheel to spin faster , center diff same principle thicker oil makes both sets tires work together , bashers use thicker oils racers use lighter oils , if go too thick puts more strain on other parts usually good to go little thicker
@2shoestoo4 жыл бұрын
Paul Clancy so are you saying thinner oil is more like a limited slip diff and the thicker the oil is moving towards more off a locked up diff?
@Openthrottlerc4 жыл бұрын
@@2shoestoo yes thats right.
@HL-OOI4 жыл бұрын
No o ring grease? 😁 so nice these days with all those nice accessories..
@nontl51972 жыл бұрын
Is it ok to use brake cleaner instead of nitro cleaner ?
@codyprice02952 жыл бұрын
You guys are the best. My automotive a$$ telling me to fill the case. Lol 😂 “but it ain’t got no seals!!!” Scratches head 💡 “Amain!!!!!”
@AMain_Hobbies2 жыл бұрын
Good thinking! Happy the video could help. -Brett
@trimmin4203 жыл бұрын
I just put 300K in my center diff on my typhon 6s what a difference that made now im looking at the front and rear any suggestions on fluids for both front and rear with a 300K in the center?
@AMain_Hobbies3 жыл бұрын
Whatever Arrma recommends. If you make the front and rear diffs too thick the car will have reduced steering and cornering. -Brett
@trimmin4203 жыл бұрын
@@AMain_Hobbies well i just put 30k in the front 300k in the middle and 80k in the rear and it drives AWESOME no loss of steering, as a matter of fact it steers better than before much more responsive in every aspect
@AMain_Hobbies3 жыл бұрын
@@trimmin420 Excellent! Glad to hear it. -Brett
@aviano724 жыл бұрын
Diff Dunkers ?? LOL, i use them for my tea.
@AMain_Hobbies4 жыл бұрын
Ha! The Tea Dunker. -Brett
@TheGorillafoot3 жыл бұрын
I love the loose tea brew ball haha! Yeah, that's a super special tool lol!
@Ev0ltion Жыл бұрын
5:24 isnt it used to make tea and just rebranded and overpriced like 5 times as rc tool?
@Tayhorix4 жыл бұрын
is it possible to use vasiline if you dont have oil (i know it sounds rediculous )
@AMain_Hobbies4 жыл бұрын
From what i've read, Vaseline will melt with heat and friction, making it not ideal for this application. -Brett
@MegaALO103 жыл бұрын
Can I use blue lithium automotive grease instead?
@alexbekkala17184 жыл бұрын
One thing that would have been good to mention is dont over tighten the diff screws! I like to just use 2 fingers on my driver once there almost all the way down.
@AMain_Hobbies4 жыл бұрын
Yes, good point Alex. -Brett
@___ll___13218 ай бұрын
You are never doing a vacuum inside that diff, i think it makes no sense
@gonzodetroitify4 жыл бұрын
Wicked sharpy tip Brett. Awesome show 🎩🍺
@workingjoe8983 жыл бұрын
I’m lazy, I’d prefer ball differentials.
@MrSneakyGunz Жыл бұрын
3:22 😂 My FAVORITE part of this video! I think I commented years ago on this but, You always do amazing work Brett.
@mranhs953 Жыл бұрын
helo sir asking about the diff my diff always leak whats the problem is that can you please explain it to me why its always leaking tell me how to solve this problem or can i use lithium crystal ep grease p-611 or how many cst can i use for my diff thanks a lot your info
@afarmer43 жыл бұрын
Why worry about getting all the bubbles out of the fluid when you are leaving a gap above the satellite gears anyway? unless you fill the entire diff ( when it's all put together ) there will be air in there and when moving it will create bubbles? Maybe weighing the diff and fluid the manufacturer know the weight and knows it will have zero voids for air???
@AMain_Hobbies3 жыл бұрын
All that empty space is filled with the other sun gear when the differential is sealed together. If you did not leave this room, the two halves of the diff would not screw together. -Brett
@afarmer43 жыл бұрын
@@AMain_Hobbies I get that you need to leave room. That's why I ask why bother getting all the bubbles out of the diff oil, there is room/air in the diff anyway
@joshuajkoplin8 ай бұрын
@@afarmer4The other Sun gear fills the space of that air when you put it together leaving no air space.
@albundy6284 Жыл бұрын
Thank you so much for making this video. I'm buying a bunch of different oil weights from amain to experiment with my tenacity db pro.
@troyflanagan42373 жыл бұрын
Brett iam getting New gears for my it was not THE slipper Clutch it was the gears my Question to u should i stick with the plastic gears and shimme them or go WITH Aluminum gears or steel hot racing gears cause i know its going to happen again with New plastic gears the 4s has to much power for plastic gears should i shimm them would that help i watched the owner take off the 2 poles the 1 underneath to tighten Slipper Clutch and take off the. Red pole and unscrew the Engine lossing it up that to way down to the gear differential i haven to get Nrw gears set put in and before i left shop i ask him to check Everything ovet thoughly Before i get it back whats the name of this fluid i can purchase?
@AMain_Hobbies3 жыл бұрын
What gears are you talking about? Most all gears in the Arrma 4S BLX vehicles are metal. -Brett
@troyflanagan42373 жыл бұрын
The plastic 1s way at THE bottom of Truck when i take off the pole to get at the slipper Clutch And the red it at bottom rear End of Truck right at the bottom i can hardly see them i think u understand what i mean
@troyflanagan42373 жыл бұрын
Not the metal 1s forget the Name of them Brett
@troyflanagan42373 жыл бұрын
WHATs The Name. Of that fluids that Everyone is Talking about Brett to put into the 4s kraton or for Any remote Control Truck
@troyflanagan42373 жыл бұрын
@@AMain_Hobbies its the spur gear Brett Not to familer with the gear systems like i said i just know the basics i wish i had Somebody to teach physical standi right beside me showing me plus my hand is broken right hand the 1 i work with so it makes it a whole lot Even if i djd know to fix gear problems how
@sm64513 жыл бұрын
Great video. Loads of information laid out simplistically. By the way, I have a Kyosho Fazer MK2 GT3 and would like to know what differential weight to start at. Any recommendations?
@DanRussell-q8s7 ай бұрын
Simple brake cleaner works very well .
@nighthawkj30A43 жыл бұрын
I just inspected the front Differential in my Rustler 4x4 VXL. It need some but ll do that next time.
@donkhron55904 жыл бұрын
Who's this dude?? Lol jk
@fonix58857 ай бұрын
How much Cst for front diff in trophy truck 1/10????
@AMain_Hobbies7 ай бұрын
The instruction manual will know best what weight to use for your specific vehicle. -Brett
@PilotRyanMedia4 жыл бұрын
perfect thanks!
@patriotrob70664 жыл бұрын
I have 1m in my Dr10 it's like cement!!
@AMain_Hobbies4 жыл бұрын
1M is intense! Should produce some intense wheel spins and dirt flings. Sounds fun! Cheers. -Brett
@Hb-xd7fk3 жыл бұрын
Too much talking. Get to the point
@JamesDirtRC8 ай бұрын
That is for Tea bags LOL
@43SunSon3 жыл бұрын
I hope I wont need to do this since I need to tear down the whole car to disassemble the differential
@willshealy36876 ай бұрын
Can you use wd40 instead of the nitro cleaner?
@AMain_Hobbies6 ай бұрын
I'd avoid using WD40 because it's a better lubricant than a cleaner. Brake cleaner will work. -Brett
@hectorramirez88322 жыл бұрын
I own a Kyosho Mad van. Only has a 2 spider gear setup that uses grease. Have the option to upgrade to a 4 gear set up with a recommendation to use dif oil. I noticed some people use grease instead of Dif oil. Is using dif oil better? Should I just use grease since my diffs only have 2 spider gears? Any recommended grease if so? Newbie here.
@AMain_Hobbies2 жыл бұрын
Grease can be purchased in bulk for cheap and is a good substitute for silicone differential oil. Is it better? No. Is it cheaper? Yes. For bashing, does it matter? Probably not, unless you are tuning your diffs or trying to achieve a desired result. The most important thing is to keep something in that differential; letting it run dry is baaaaaaad. -Brett
@jackdurden4663 жыл бұрын
I’m learning so much about my last unknown area of my truck, the entire damn drivetrain. I know, it’s incredibly important to take care of it, but I’ve never had any need or problems which required immediate attention. So I ask, if want to replace anything that may need to be while in there, my trucks an old 2.5 Revo, with several upgrades, but none to the drivetrain, yet. So any suggestions as to what could or even should be done while in there? I’d want to swap out the bearings as I’m just prone to always doing that. Any more than that I just don’t know. So any advice is welcome!!
@AMain_Hobbies3 жыл бұрын
Very happy you're exploring and learning about your truck! The r/c transmission are pretty simple but look intimidating. Usually for servicing, clean the inside the case, clean/replace bearings, freshen up the diff with new fluid, replace diff outdrives if they are worn, and maybe replace the idle gear too if it has any signs of wear. When you're re-assembling the transmission, add a little lightweight grease to one of the gears which will spread when all the gears are rotating, helping smoothen and quiet the transmission. This is what we use: www.amainhobbies.com/protek-rc-premier-white-friction-noise-reducing-gear-grease-lubricant-10ml-ptk-1412/p-qeaqtsqq6mzxactz How we apply the grease on the diff at a diagonal for full teeth coverage (go to 10:00 minute mark in this video: kzbin.info/www/bejne/b5Cnk3-CgK-ahNk) Here is our how-to on changing diff fluid: kzbin.info/www/bejne/qmq3ZX9ujsZkfqs -Brett
@i.p.outdoors38253 жыл бұрын
a small glass jar and lighter fluid work wonderfully.
@MikeS-cv8xs Жыл бұрын
Amain hobbies= no nonsense straight to the point. Kudo's
@nighthawkj30A43 жыл бұрын
My Rustler 4x4 VXL front diff been leaking things brand new. Smh should call Traxxas tell them its been leaking.
@AMain_Hobbies3 жыл бұрын
Might have happened during shipping. Sometimes if the box was flown, the air pressure can cause the fluids to leak. I'd definitely check it out, and if there are serious issues, let Traxxas know and they'll send you out what you need. Hope you get it resolved and outside driving! -Brett
@nighthawkj30A43 жыл бұрын
But i love this video though very entertaining and has many useful information.
@cocoasuransisemarang3 жыл бұрын
I just bought an Arrma Typhon 6s V5.. when should I do regular service changing diff oil?
@AMain_Hobbies3 жыл бұрын
Please read your owners manual. -Brett
@justinrayford36493 жыл бұрын
Love the content! Thank you for sharing your experiences and tips its much appreciated 😁
@SolamenteVees2 жыл бұрын
I’m an old racer who only knows ball differentials for off road. Why did the industry change to gear diffs?
@AMain_Hobbies2 жыл бұрын
1/10 Off-road dirt racing still uses the ball diff typically. The gear diff has been used more recently as tracks tend to get more and more high-traction. -Brett
@ramonbmovies9 ай бұрын
How do you know what kind of diff fluid to use? I've seen some people recommend white grease.
@AMain_Hobbies9 ай бұрын
The vehicle manual should state what fluid was used, or recommended for use. If the manual doesn't state what weight fluid was used, they may have used grease instead, which can be a suitable, inexpensive alternative. The viscosity of grease though is not easily adjustable like silicone fluid, and naturally, grease has a lightweight viscosity. For 2S/3S power needs, this may be ok, but for high-powered 6S power needs, the viscosity may not be adequate. So, it just depends... -Brett
@johnm8558 Жыл бұрын
Great Vid. Wow! I wish I could find a Fluid Video for my New Associated B74.1D Center Diff. Oh I am on Bag 10 trying to get it Built. And the weight part is just not working on the Center Diff for me, and there manual Sucks for directions! I Emailed Associated today, they just said go with the line in the Picture. I dont want to Blow my New Diffs. Per there Warning!!! Im so not Happy with this Kit at all..
@AMain_Hobbies Жыл бұрын
There's no harm in filling the diff cup to the line in the manual. If too much fluid is added, pressure will cause some to seep out; if not enough fluid is added, the fluid will break down slightly faster. Neither way should cause the diff to blow out though, so you should be ok. -Brett
@johnm8558 Жыл бұрын
@@AMain_Hobbies I 100% understand about Pressures and what to Little or To Much can do even to a Automobile! This is why I am Trying to do a Proper Build and not Micky Mouse!!! PER Associated, It is important that the correct amount of fluid is added to the diff. Too much fluid may cause the diff to fail. I DONT NEED OR WANT THIS!!! Interesting, If you think about it there is NO way a Liquid Line can go Straight Across! in a Cup.... Its going to be like a U or a V shape so that is Not a Straight Line! So in Reality there is NO Real Line! ITs also Interesting Associated made the kit And they have NO Clue what the Dry weight is before adding any Fluid.. They couldn't even Tell me Properly all of what parts for the Center Diff that go on the Scale, Because no matter what I had Put on the Scale Nothing would weigh 44.5g. The Manual Directions are Typo'd so Bad!!! No one knows how to Weigh the Center and that just Stupid for it to even be in the Manual!!! Thank you
@michaelfraley46602 жыл бұрын
What's a good upgrade weight to do in all the differentials I wanting to grease the gears that are involved so might as well do the swap on the differentials.
@michaelfraley46602 жыл бұрын
Would it be a good to change fluids in all differentials and what weight. I running 20/50 gearing with Proline Trenchers HP Belted 3.8 I do not bash.
@zulurcracingteamzulurcrt15174 жыл бұрын
Kinda too intricate. Are there pre-assembled diffs, just plug and play? 🤔😅
@surfside753 жыл бұрын
lol... Yes I think so. Or you could just buy new Arrma rtr truck every time something wears out to keep our hobby going forever👍😂
@subradiant_music2 жыл бұрын
amazing video Brett! Covered everything. IS there a video covering the best weights?
@AMain_Hobbies2 жыл бұрын
No, it varies so much depending on the car and application. We usually recommend to follow the setup sheet for the vehicle. -Brett
@FZERO202 жыл бұрын
Y’all can hate if y’all want but my closest hobby store was closed so I tried my Lucas oil stabilizer and it worked pretty nice up front. I tried bar & chain oil in the back because it was thicker. Really transformed handling and acceleration
@NeighberhoodRC6 ай бұрын
Is it better to have metal diff case than the stock plastic one ?
@AMain_Hobbies6 ай бұрын
Yes and no. In some cases an aluminum diff case can help dissipate heat generated inside the diff. It can be especially helpful if you're in hot environments. But if you're not, it might not be worth it. -Brett
@NeighberhoodRC6 ай бұрын
@@AMain_Hobbies I have a v5 blx 6s notorious stunt truck and it’s not doing willies no more that’s cause I need new diff right ?
@DashzRight3 жыл бұрын
What if you put lithium grease inside? Will it explode?
@AMain_Hobbies3 жыл бұрын
No. That grease is a good lubricant but not very thick, or lacks a high viscosity. But it would work and it's better than nothing inside. -Brett
@kaycee93372 жыл бұрын
What gear will give me more top end 14/45 diff .or 15/42 front
@AMain_Hobbies2 жыл бұрын
The 42/15 should have more top end of the two. -Brett
@edwincordero84 жыл бұрын
Hi friend. On my DR10, which aftermarket diff oil fluid viscosity should I use to keep it running like stock?
@AMain_Hobbies4 жыл бұрын
Team Associated doesn't say what specific fluid they used, but I'm guessing it is about 5K. So if you want to keep it stock, 5K should do it. Unfortunately, the Team Associated fluid is all sold out, but this Mugen Seiki fluid is very high quality and a great alternative: www.amainhobbies.com/mugen-seiki-silicone-differential-oil-50ml-5000cst-mugb0322/p453219?v=1754 -Brett
@edwincordero84 жыл бұрын
@@AMain_Hobbies Thanks Brett.
@firasoji3044 жыл бұрын
You did it, yay. Thanks man.
@AMain_Hobbies4 жыл бұрын
Hope it helps CloudFire! -Brett
@RyanRyan-vn1ru4 жыл бұрын
What can I do I have the Losi 8ight T RTR my front tires are spinning before the rears what can I do to fix that I don't race I just play in the backyard with the boys
@AMain_Hobbies4 жыл бұрын
Sounds like your center differential fluid might have broken down, or is too light. Adding new fluid would help, maybe 10K is the stock weight. The heavier the fluid, the more all-the-time 4X4 it will be, but this generally reduces performance, but if you are just bashing around, it shouldn't matter. We have used 1Million weight center fluid before and it's some serious wheelie popping action, although it's really hard on the vehicle drivetrain. Maybe try 100K fluid if you are just bashing around. Check this out (and you can select different weights from the drop down above the blue add to cart button): www.amainhobbies.com/team-associated-silicone-differential-fluid-2oz-100000cst-asc5459/p453215?v=223792 If you have a broken part in the drivetrain, in the rear end, this will cause all power to transfer to the front end. So be sure this isn't the case. Maybe pick up the car off the ground, and make sure all the tires spin with the same force, when you give it gas. Hope this helps. -Brett
@ricksprings4 жыл бұрын
Had this happen to me with Tacon truggy. I've used white lithium grease and shock oil in my diffs before, lol....
@rc_dubai4 жыл бұрын
love your videos, awesome !!
@AMain_Hobbies4 жыл бұрын
Thank you RC Dubai! Greetings from Chico, California. -Brett
@tjenkins11264 жыл бұрын
This came out at the right time. Just got my Kyosho outlaw pro together and took it out for the first time. Diff is more slip than limited, so guessing I need to go with a heavier weight oil. I'm used to locked spools in my crawlers and just making sure they're well greased. Is there a reason things like the KORP and others have open diffs over being locked? More prone to breakage with high volt brushless set ups? Thanks for the content!🍻👍👊
@AMain_Hobbies4 жыл бұрын
A big reason is you just wouldn't be able to turn with locked diffs. Crawlers barely pull it off and must use extreme steering angles, a dig unit, or a front overdrive to overcome this. In sand or mud it is superior, but for anything with decent wheel speed, on a surface with decent traction, a vehicle with locked diffs would perform poorly. The diffs also help distribute power to areas with the lowest resistance, to keep wheel spin to a minimum. When your tires break loose and are spinning, you have lost traction and control of the vehicle. There is a lot to it, but I hope this shines a little light on the topic. Great question and congrats on the cool truck! -Brett
@tjenkins11264 жыл бұрын
@@AMain_Hobbies Totally get it, guess I assumed everyone plays in the dirt, where a locker helps and you just slide the rear end around. Throttle stear, if you will. Never thought about high traction situations where the diff needs to the job it was literally designed to do. Appreciate the time and convo man, keep doing what you do.🍻👍👊
@sonny19802 жыл бұрын
What weight fluid do u recommend on a 1/14 scale?
@AMain_Hobbies2 жыл бұрын
Shoot, not sure. I recommend seeing what the manual recommends and adjust from there if you need to tune them. -Brett
@wise--men3 жыл бұрын
Hi friend, I'm from Brazil and I have some questions. I would be very happy if you would help me! I have already discovered that it is necessary to apply grease to the outer gears of the differentials, but I really wanted to know if I should also grease the gears of the engine. Example: 6448 parts: Spur gear, 8985: Input gear transmission, both from Traxxas Maxx. Another question is that the center differential gear comes into contact with a motor gear, should I grease it too? Part 8988. Inside Driveshaft 8949, do I also need to apply grease?
@AMain_Hobbies3 жыл бұрын
No, it is not necessary. The grease is good for metal on metal gears, but with a plastic spur gear it is not necessary, although adding grease will do no harm. The only concern is the grease will attract dust and dirt, so you may need to clean that area more often. -Brett
@wise--men3 жыл бұрын
@@AMain_Hobbies Nice! Thanks for the answer! I really want to keep my RC cleaner, with less grease even. I bought my Maxx from you guys! =D
@AMain_Hobbies3 жыл бұрын
@@wise--men Thank you Marcelo and congratulations on the Maxx! It is an amazing truck. -Brett
@jamesvdm8 ай бұрын
Great video!
@markgates38084 жыл бұрын
what is the part number for the shims used on the outside of the diff next to the bearings
@AMain_Hobbies4 жыл бұрын
For 1/8 scale diffs, it's probably these: www.amainhobbies.com/protek-rc-13x16x0.1mm-drive-cup-washer-10-ptk-h-5903/p188791 For a specific model, I would need to know what brand and vehicle you're talking about. -Brett
@kylevogler68634 жыл бұрын
the gnk basket is a ikea loose tea maker
@Ev0ltion Жыл бұрын
To me it felt like a shortcut diff rebuild. I usually tear them down compleatly and regrease all the seals after deep cleaning all the parts.
@AMain_Hobbies Жыл бұрын
This is a video showing how to change the fluid, not completely rebuild the diff. -Brett
@Ev0ltion Жыл бұрын
@@AMain_Hobbies Still from my expirience fluid catches very fine dust from gears grinding inside and it can damage seals or increase the wear on crosspins if allowed to build up. In my opinion its worth to always do a full rebuild. Sorry if you took my initial comment as "trash talk" it wasnt meant to be one, more of a discussion starter.
@josh_rit80454 жыл бұрын
Great video! Loved Brett's take on what tools you'll need!
@ramtrucks7213 жыл бұрын
Can I use Valvoline synthetic gear oil instead?
@AMain_Hobbies3 жыл бұрын
I don't know for sure, but i'm guessing it's too thin and would leak out. Black grease is a great solution for a light diff. -Brett
@chrisstich54742 жыл бұрын
Great info. Thanks!
@winstonoso58213 жыл бұрын
If I change the center diff fluid, do I have to reset the mesh on a kaiju??
@AMain_Hobbies3 жыл бұрын
Not sure. Do you have to move the motor to remove the center differential? You should be able to leave the motor secured to the motor mount, and just remove the center diff. But i'm not that familiar with that vehicle so I'm not 100% sure. -Brett
@winstonoso58213 жыл бұрын
Ok.. No u don't have to remove the motor to get the center diff out. Thanks for the info. 👍
@johningam34524 жыл бұрын
I am Newish to the hobby what is the best diff fluid weight to use just for bashing in a 4wd
@AMain_Hobbies4 жыл бұрын
Hey John. You'll probably want to use the same viscosity fluid that was in there, unless you're trying to change some performance characteristic. What vehicle do you have? -Brett
@johningam34524 жыл бұрын
Fs racing victory the one that drive on water. The diff gears in the rear keep braking I don't run it hard or jump it more then like 2 feet I air
@billimono44804 жыл бұрын
can you use motor spray to clean old diff oil off the gears?
@AMain_Hobbies4 жыл бұрын
Yes, you bet. Nitro cleaner and motor spray are pretty much the same thing. -Brett
@grumpymissblysdroneadventu72244 жыл бұрын
Just adding a 👍 from here.
@jaguarsrcfamily1014 жыл бұрын
Cool video is that from an arrma 6s .??
@AMain_Hobbies4 жыл бұрын
You nailed it. That is the center diff for the Kraton 6S BLX. -Brett
@nitrogas57194 жыл бұрын
Could you please do a tutorial vid on how to sim differentials
@AMain_Hobbies4 жыл бұрын
Pro R/C Racer Ryan Lutz just made a video on this topic, so I'll link to his video below. He's a heck of a racer and he knows his stuff. Hope it helps shadowgamer. kzbin.info/www/bejne/nHbSgJ95n9OVgZo -Brett
@Milfmilker-gd6gm3 жыл бұрын
Is RC nitro cleaner the same as carb cleaner
@AMain_Hobbies3 жыл бұрын
From my understanding, most r/c nitro sprays are automotive brake cleaner; not sure about the carb cleaner. -Brett
@tahayt61423 жыл бұрын
What happens if your diff has no diff fluid
@AMain_Hobbies3 жыл бұрын
Then the diff will spin very easily, or "diff out." The fluid is there to provide resistance; with no fluid, no resistance = very easy to spin. -Brett
@xXxREDEEMEDxXx-yc9ne4 жыл бұрын
Can you use synthetic grease for the diff?
@AMain_Hobbies4 жыл бұрын
I've read some people use that in their diffs so it should work, although not sure if there are any drawbacks. -Brett