ANSYS Workbench | Contact Non linearity | Interference Analysis

ANSYS Workbench | Contact Non linearity | Interference Analysis | Solid Mesh |

Рет қаралды 50,535

Күн бұрын

Пікірлер: 21

@kirankumarpgoudar9581 4 жыл бұрын

Hi tutorial is good and clear. my question is y you have chosen formulation as augmented Lagrange method?

@nayakankit 8 жыл бұрын

Thanks a lot sir for your valuable tutorial....

@ANSYS-India 8 жыл бұрын

Thanks. Keep sharing videos to those who want to learn

@monubector9527 8 жыл бұрын

Great tutorial Sir.I am encountering a similar problem where I have to release the shrink fit and take the shaft out of the hole. Means I have to heat the external body only at the outer surface i.e. how much heat transfer W/m2 C is required to have zero contact stress at the interface. Let me now if you have encounter similar problem in the past.I am doing a static analysis first i.e. define the shrink fit and then connect solution to thermal analysis where I defining heat transfer coefficient till I got zero contact.Need your advice

@obeidi1 9 жыл бұрын

Great job. thanks

@ANSYS-India 9 жыл бұрын

For more Tutorial Videos Click on the link below ANSYS Workbench kzbin.info/aero/PLOahOE6DpL4qq_QxPHieAeVejzDP1yIYW ANSYS Multiphysics kzbin.info/aero/PLOahOE6DpL4qojPO7_GkgkVC-cB8KFMeC Hypermesh kzbin.info/aero/PLOahOE6DpL4puVylWdpHWRoGhIfswDc6T Creo Simulate | Pro Mechanica | kzbin.info/aero/PLOahOE6DpL4qvb2Z0Ir8SwvUyv0qnRGH4 Creo Parametric Tutorial kzbin.info/aero/PLC1voSxuLSym29Dt_xNnIJxBCtE-k9iul Pro E Wildfire Tutorial kzbin.info/aero/PLLBsoJO8DYcVGLa_se2y5Ao0Vzwy6TUbz For online training on ANSYS Workbench | Creo Parametric & Simulate | Pro E Wildfire & Mechanica | HyperMesh | Contact: engineeringtutorsdesk@gmail.com

@fredrickmadarakamwema343 7 жыл бұрын

Thanks so much. I am trying to model a sharp tip scratching a metallic surface to see stresses around the scratch. How can I do it? Since I will need to define contacts and displacement ?

@rogerfrank1122 6 жыл бұрын

Hey...i Want to find the pushout force rrquired to disengage a bush assembled with press fit in a Hub..!! How to do it??

@mipila 8 жыл бұрын

can you show how I can put the tolerance of the shaft and the hole for calculate the pressure fit?

@obeidi1 9 жыл бұрын

can you please show how to do the drawings interfering a shaft of 11mm into 10mm hole to do similar simulation. I couldn't fit a shaft bigger than a hole using both ansys nor solid works. thanks very much and very helpful video

@ANSYS-India 9 жыл бұрын

Obedi1 please can you elaborate your problem definition, or freehand sketch your requirement and mail me to engineeringtutorsdesk@gmail.com

@najhos1440 9 жыл бұрын

Hello , Very helpful video. I am trying to simulate the same thing but in ANSYS APDL The way i approached it is to heat one part (load step 1) and then allow it to cool with the contact/target option (load step2) However only load step 2 is taken in consideration. Any ideas why this is so? thanks

@ANSYS-India 9 жыл бұрын

Naj Hos Thank you Naj, the thing which you are looking for is thermal simulation, and this tutorial is of structural simulation, please give me some time i will come-up with the solution video for your case

@najhos1440 9 жыл бұрын

GRS CAD/CAE Hi, did you have a chance to come up with the solution? If you do not have time to do the video, can you please just let me know how to proceed, and i will try to do it by myself. I need it soon. Thanks

@ANSYS-India 9 жыл бұрын

I was going through your problem, Kindly describe your problem definition with photograph to my mail address: engineeringtutorsdesk@gmail.com

@paulsingh2301 9 жыл бұрын

Hi I had a question and im running into a problem while trying to do a similar simulation. Assume your shaft and a bushing have interference fit and there is also external force presented normal to shaft. Also assume that your shaft has a step and the bushing is initially is pressfit onto the shaft and is just touching against the step. Now if I try to run the solver, I get error because i am having a hard time figuring out the type of contact to use for where the bushing is just touching the step. I get errors like rigid body deformation, contact arupt change (I tried using no seperation and frictional contact by the way). Thank you

@ANSYS-India 9 жыл бұрын

Paul, Do not worry, pls sketch your problem definition and describe about the problem, and mail me to engineeringtutorsdesk@gmail.com. I will help you out in solving this issue.