Pink and grey wires are two ends of NC relay. which gets grounded when alarm goes off, or you press remote kill.
Пікірлер: 125
@Ymon254 жыл бұрын
This video still helps people! Thank u sir. I was abaout to rip off my aalarm, but you explained it.saved me time and money
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@danielbadenhorst80843 жыл бұрын
Thank you sir this helped me a lot, i converted a car alarm to work on a motorcycle using your information. Cheers 👌🏻
@ayubshaikh9156 Жыл бұрын
Very useful Info , they write flame-out line ! Grey / pink…… Was wondering The use ? , wanted some sort of immobilising Working from this device , you clarified the purpose, thanks……
@Noeman20097 жыл бұрын
That's correct, the Grey and Orange cable with an NC Relay can be used as an engine cut off switch, Connect the 30 & 87a Pins to the engine cut off cables.
@Nariyahjhezelle6 жыл бұрын
Hui San how to install that pink wire?
@Nariyahjhezelle6 жыл бұрын
Is it needed to have a fuse
@GreatIndianJugaad6 жыл бұрын
+Jomark Sendrejas not needed, but recommended
@Nariyahjhezelle6 жыл бұрын
Sir could you give a sample of diagram from alarm to its engine cut in cdi
@Nariyahjhezelle6 жыл бұрын
Or can you the procedure how to install that enginecut
@oliverpabualan94036 жыл бұрын
Great Indian Jugaad . Thanks to this video. Its a great help for me. Soon, I am going to install this to my scooter. Kindly check if my proposed diagram is correct. On of each yellow wire, I will connect it to the positive side of my flasher wires (one at left and right flasher). For the Orange wire, I will connect it to the negative wire that supplied the key ignition switch. For Blue wire, I will connect it to the positive of the push button then lastly, I select one of the either gray or pink and I will connect it to NC relay at 86 then at 85, I will connect it to the positive supply of the battery. I will cut the connection of the ignition switch wire then I will attached it to 87a and 30 of the relay. Kindly comment plz...Tnx
@GreatIndianJugaad6 жыл бұрын
+Oliver Pabualan what are these number? Where is the diagram? Flasher is the device which converts regular DC current into flashing current. I hope by flasher you mean indicators, ignition key or switch is, as name suggests a switch on ignition wire. So there is no negative or positive. So you have to make sure you connect the orange one after the switch, so even if the switch is off, meaning key not present or in off state, the current from orange wire can reach all necessary devices. Same with blue, it has to be connected to the positive of starter solenoid. Follow the wires from self start button they will take you to starter solenoid if don't already know that. And I don't understand rest of the codes.
@tibany57 жыл бұрын
The gray and pink wires are for the option of turning the engine off "Anti Hijack Mode", so these wires are very important and should be connected in series along the Engine Stop Switch circuit.
@GreatIndianJugaad7 жыл бұрын
+Talal Altibany Not every Bikes engine stop or kill switch works in the same way, like in my Bajaj Pulsar(India) it does not ground the pulser coil signal, it cuts off the power to the CDI and starter relay motor. If your Bike has the switch which kills the engine by grounding pulser coil signal then sure, your method can be used. But since there is no grantee of what system your bike has its alway safe to connect any one of them the the pulser coil or timing coils signal wire going to the CDI, that way it will still work as "anti hijack thingy". If i do as you say and if someone tries to steal the bike by using a key or shorting the wires my bikes fuse would blow or the anti theft device could burn because of excessive current. Hope it helps. :)
@nuwandh3 жыл бұрын
Nice work bro. It was a good explanation. I was looking here and there for to find what is the purpose of this two wires. I need to use this kind of alarm with my car central lock system. so,I need to trigger any signal for lock and unlock the central lock. it seems possible with these two wires. If so how can i connect it with central lock system. thank you
@uvindunimsara21794 жыл бұрын
Good explanation with prove.. thanx bro
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@harveshsinghthakur66673 жыл бұрын
Super vedio excellent knowledge.
@yourstruly9340 Жыл бұрын
I hope you can shine some light on my problem. I have the sabvaton 72150 controller that I want to add an alarm to but the seller from Alibaba forgot to add the anti theft plugs. My alarm has two plugs. One plug has red & black for (power), the other plug has three wires, Orange - for ignition (key), Brown- connect to blue phase wire for (mtr signal input) and blue to anti-theft. The problem is my controller does not have the plugs. I read in a forum I can ground the blue wire because it will complete the mtr signal (brown to phase) wire during activate ( alarm sounding) what you think? Thx for any help you can provide.
@akhilgamingyt9767Ай бұрын
The starter wire sends postive signal to turn on the engine by self but bikes like yamaha r15 uses negative signal to self so what should i do
@JeffMotoDronelian0630176 жыл бұрын
Sir pls show me the diagram on how to connect the pink or grey wire. Tnx sir god bless you
@GreatIndianJugaad6 жыл бұрын
+alejo taglorin its different for every vehichle
@darkaricus42265 жыл бұрын
Guys if you press the electricity button on remote the pink grey wire is cut off. so use change over relay connect the number 30 on bat. then connect the 87a on cdi. 86 connect to the grey wire. 85 is connect to ground. and the 87 on indicator light means that is it light is on the engine won't run if the light on indicator is off means that the engine will run and pink wire is the ignition switch. I use cyclone motorcycle alarm
@nehemiah24667 ай бұрын
where do i connect the grey and pink wires..My bike is TVS HLX 150
@techman6431Ай бұрын
What about Activa 6g Bs6 2022 model for pink n grey wire pls reply
@akibekhan24806 жыл бұрын
Thankyou bhai nice video
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@beyondclosedoors16 жыл бұрын
Thanks for video
@eddieb69835 жыл бұрын
I have a 2016 zx10r, in the instructions I'm supposed to cut the CDI or flameout wire & connect the pink &gray wire to either end. If so what color is the CDI or flameout wire.
@GreatIndianJugaad5 жыл бұрын
sorry can say with having a look. but generally CDI or flameout wire is the one going to kill switch, so you can back trace it.
@woodenspoonUto5 жыл бұрын
i’m not sure if i understand it right, if you arm the device the continuity of pink and grey disconnect and if unarmed the continuity returned?? it’s right??
@GreatIndianJugaad5 жыл бұрын
continuity begins only when alarm is set off. they stay disconnected when unarmed or armed stage.
@rgawde686 жыл бұрын
nice vdo... u have tried expaining smthing which is very important... but your camera was showing what u were doing with the wires nd i clrerly didn understant wht u were doing.. i hv a problem.... i connected my pink wire to ignition but when i try to make hijack entry to ignition key... my black wire which is connected to negative gets heats up n starts showing smoke... grey wire not connected.. pls explain
@GreatIndianJugaad6 жыл бұрын
+Siddhesh RC i never said connect pink wire to ignition. Pink wire is basically ground wire, when alarm is active, and ignition wire is positive, when keys is on. You basically short circuited your bike. You may as well have burnt your alarm unit.
@GreatIndianJugaad6 жыл бұрын
+Siddhesh RC be careful.
@chamcrafts32344 жыл бұрын
Perfect
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@lot37416 жыл бұрын
I got the basic idea my friend thanks. But would it make a difference if my bike has 4 ignition coil? Plug it in one of them? What about kill switch? Sorry im not electrically inclined. Thanks in advance for your help
@GreatIndianJugaad6 жыл бұрын
+lot gendrala do you mean you have more than one cylinder, or 4 spark plugs for one cylinder? And Did you understand what you want to know about kill switch.
@lot37416 жыл бұрын
Great Indian Jugaad i have 4 ignition coils. One for each of the 4 cylinders bro. If this is the case, where do i connect the pink wire
@GreatIndianJugaad6 жыл бұрын
+lot gendrala I think spark timing on your engine is digitally controlled by one CDI. So there should be on one pulser coil signal wire, attach the pink wire there. So as to ground the signal which will take out all the sparks.
@lot37416 жыл бұрын
Great Indian Jugaad thanks my friend. Youve been a huge help.
@jackcolman42046 жыл бұрын
Hi a have scooter in ignition key 2 wire is there color red and (orange)not sure more dark in orange. I tap orange wire of alarm in orange color and blue wire of alarm in push start positive. it's is correct? Remote start/off is working.. it's safe to tap orange wire there or no? 2nd question where to tap pink/gray color of alarm?
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@kjvlogs59565 жыл бұрын
hi i have the same alarm, i wanna know if we can turn off the sound when activating the alarm or dactivating it.. or minize the sound.. thank you..
@GreatIndianJugaad5 жыл бұрын
Don't connect the speaker (or) s. Or to reduce sound put a tape on speaker.
@Notis3116 жыл бұрын
Hi a need some help , there are Two Black wires in my alarm , one comes from the harness along with the Red(possitive) and there is one more Black wire that comes directly from the alarm brain , which is the corect one for the (-) negative battery pole ?
@GreatIndianJugaad6 жыл бұрын
The second one should be of a pair, and it should be for the speaker. the one in the complete harness should be battery negative.
@sauravsanjat20032 жыл бұрын
Hame link bataye hame dusra mil gaya
@bojanx1005 жыл бұрын
Ever got to doing that keylessgo stuff? As in removing the ignition key all together?
@GreatIndianJugaad5 жыл бұрын
I have all wiring diagrams ready, Its just I'm getting tym to start working on that project. I will start that project in April 2019. Really sorry for the delays
@bojanx1005 жыл бұрын
@@GreatIndianJugaad thanks for response. I am just trying to do the same thing but have no clue yet, how to accomplish that using the device and relays alone. Can you give me a hint weather it's doable at all or not, given you probably spent more time on it. I was thinking of latching relay using that gray or pink wire but have no idea still. Any suggestions would be really appreciated.
@bojanx1005 жыл бұрын
Came to conclusion that PKE of my unit is totaly useless. Using a relay I can steal bike ignition power with help of gray wire. But with PKE autolock alarm is not trigger when bike is hotwired only if moved and hotwiring disables that alarm. So for the keyless on my particular unit only pressing button of a key would work, not quite the keyless I was hoping for. Please share if you did find a way to properly use PKE to give ingnition power to your bike and switch it off after you move away from the bike. Thanks
@GreatIndianJugaad5 жыл бұрын
you will have to manually check all the buttons on your Anti theft device, for there functions, simply put it just a set of NC and NO relays. each key turns one or more relays 'ON' or 'OFF'. so you can use one of the NC relays to act as ON OFF switch for another NC relay which will turn your bike ignition ON or OFF and the reason for not using the relay on the device itself is that it might not be rated for your Bike entire working load. It might seam complicated but it really easy. Good luck with your project.
@GreatIndianJugaad5 жыл бұрын
sorry could not understand what you meant by PKE
@mohitsengar60155 жыл бұрын
How to get negative 12v potential through blue wire as my Yamaha's starter relay working on negative potential
@GreatIndianJugaad5 жыл бұрын
there is not negative or positive potential. It is called potential difference. its the difference between high and low voltage. so -12v and GND(or 0 volt) is is still 12 volt potential difference. -12v and 3.3v is 15.3 volts
@nithindavid30105 жыл бұрын
Sir need u r help for wiring connection
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@darkaricus42265 жыл бұрын
I don't think if the pink wire and grey wire are grounded?
@GreatIndianJugaad5 жыл бұрын
really sorry, can you explain a bit.
@chanvitsermchief87425 жыл бұрын
if i connect gray wire to cdi, what do i connect pink to? do i connect the pink to orange 12 volt supply?
@GreatIndianJugaad5 жыл бұрын
NO!!! leave pink as it is.
@VHER05087 жыл бұрын
is the connection same with yamaha exciter 150i fuel injected? thanks in advance
@GreatIndianJugaad7 жыл бұрын
+rhev jeres not sure, you will have to find out what kind of kill switch arrangement you have.
@Nariyahjhezelle6 жыл бұрын
What relay will be use if u want an engine cut off?is it connected to cdi?
@GreatIndianJugaad6 жыл бұрын
+Jomark Sendrejas sorry i didn't really follow the question, you want external relay for engine cut off?
@Nariyahjhezelle6 жыл бұрын
Great Indian Jugaad yes i want to wht is needed to have a engine cut off
@Nariyahjhezelle6 жыл бұрын
I want to what relay is needed in Engine cut.off?
@Nariyahjhezelle6 жыл бұрын
And i want to ask how to install it and are the procedure of it
@GreatIndianJugaad6 жыл бұрын
+Jomark Sendrejas didnt you watch the video? I explained it there. Every bike is different, I gave the general idea that would be common for all bikes. You need to study diagrams of your motorcycle then you will understand.
@pardhasaradhikannikanti77357 жыл бұрын
I have recently installed this setup, but remote start is still staring even bike is in gear, what shpuld i do, please help
@GreatIndianJugaad7 жыл бұрын
+pardha saradhi kannikanti it's very difficult to with looking into it, sorry. But I say you have a problem with starter relay ground. Bcs ground is connected only on neutral or when the clutch is pressed. If you have ground on starter relay in other gears then then that's your problem.
@wllvlogs7 жыл бұрын
I connected the orange wire to flasher relay. Should I remove it? And I tried to connect the blue wire on push start wire and it doesn't start at all. I think, its because I cant find the ignition wire so that I can connect the pink wire. Help me please. Thanks in advance
@wllvlogs7 жыл бұрын
I mean, it doesn't start on remote but it flash a red light on tail. By the way, I'm using Yamaha Nmax
@wllvlogs7 жыл бұрын
I ended up not connecting the blue wire and pink wire. but the grey wire, I attach it on the chassis.
@GreatIndianJugaad7 жыл бұрын
+William Hernandez the blue wire goes to the positive of starter solenoid or relay. ( soleniod or relay is a electrical switch,in this case a switch to turn on/off the starter motor, it general located just next to the battery and starter motor, and is connect via thickest wires in your motorcycle.) its negative input is clutch or neutral gear activated, and its positive is activated by the self start or push start button, Idea is to connect the blue wire to this positive. So that when you push the button on the remote and there is ground connectivity the start motor can start.
@GreatIndianJugaad7 жыл бұрын
+William Hernandez orange wire connected to flash is okay, i mean it will work but it not safe, if you follow wires back you will find a fuse box between flasher and ignition key. You should connect the orange wire before that fuse, for safety. And for remote start to work the starter motor need ground as well which is there in case if bike's in neutral or if you are holding the clutch.
@GreatIndianJugaad7 жыл бұрын
+William Hernandez no point of attaching grey wire to the chassis. Does not serve anything, it should be connect to pulser coil wire. Its generally located close to your alternator wires.
@MrChain-yg8uh6 жыл бұрын
How ro put relay, can i have the diagram. Pls
@GreatIndianJugaad5 жыл бұрын
What relay?
@sudarshanputi41126 жыл бұрын
I have a tvs star sport bike and i instol the alaram but where i connect white and greay wire. Pls help me
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@nathsmacs3237 жыл бұрын
sir my fuse is always dead
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y
@markvalcardenas7 жыл бұрын
Hello sir. Where is solenoid of a motorcycle?
@GreatIndianJugaad7 жыл бұрын
+Mark Val Cardenas on mine it's on the left, between battery and starter motor.
@ikentfix6 жыл бұрын
What if i tap the pink and grey directly to the ignition coin?
@GreatIndianJugaad6 жыл бұрын
you can but IGN coil has way too high voltage might damage your device.
@ikentfix6 жыл бұрын
Great Indian Jugaad i mean, i cut the wire that supplying the IGN coil, then put the pink and grey on each end of it? Is it possible? Im afraid to try it tho
@GreatIndianJugaad6 жыл бұрын
if you do that, IGN coil will not work at all. it will have no input signal thus there will be no spark.
@ikentfix6 жыл бұрын
UPDATE: I just tab the pink wire to the positive wire of IGN and i just cut the grey wire. and tadahh! it all works.
@GreatIndianJugaad6 жыл бұрын
what do you mean by positive of IGN? and also what grey wire?
@sudarshanputi41126 жыл бұрын
What we do key less system
@GreatIndianJugaad6 жыл бұрын
+Sudarshan Puti i have not started working on it yet, i soon will, and post a video.
@aeriallaag10186 жыл бұрын
how about yamaha sniper 150? same wiring?
@GreatIndianJugaad6 жыл бұрын
+jO Naxz IDK, sorry
@aeriallaag10186 жыл бұрын
the kill switch is working but the auto start ddnt.. thank u
@GreatIndianJugaad6 жыл бұрын
+jO Naxz auto start only works in neutral or when clutch is pressed, if connected right.
@aeriallaag10186 жыл бұрын
Great Indian Jugaad in my case instead of auto start engine only the switch will on.
@aeriallaag10186 жыл бұрын
What is the color of the wire of the alarm and the color of the wire in the motor need to connect so that it will auto start.
@giriphotog7 жыл бұрын
can you give me ur email id. i wold like to ask a doubt. i have wiring diagram of my scooter too .
@GreatIndianJugaad7 жыл бұрын
+Giri Photog i have fb page with the same name, and username is shudhDesiJugaad, you can send a msg there.
@GreatIndianJugaad7 жыл бұрын
+Giri Photog facebook.com/ShudhDesiJudaad/
@Rahulmarandi927 жыл бұрын
install pulsar rs200 instructions
@GreatIndianJugaad7 жыл бұрын
+Rahul Marandi wire color wise instructions toh nhi de skta, mere pass hai nhi RS200 but pattern same hoga jo is video me bola h, wire color hr bike ke alg hote hain.
@manishsingh69075 жыл бұрын
Hindi may
@GreatIndianJugaad4 жыл бұрын
ek doosra video h, hindi me.
@GreatIndianJugaad4 жыл бұрын
Make any motorcycle Keyless/Remote start stop in Rs 500-800 kzbin.info/www/bejne/ZpiYqKKLl7OLr5Y