Application of Flintlastic SA roof system for low-slope residential roofing

[@HsingSun]

Thank you for your video. Question: Which is the better one, Synthetic (peel & stick) or Flintlastic SA roof system?

[@johnferber5864]

Base sheet. 2 of the 12 rows blue membrane removed, then caped over. Should I be worried? Wish I could post pics

[@ronschlegel6396]

The minimum for the shingle tie in should not be one inch but half the shingle size for it to be water tight

[@jban4457]

Are you suggesting that the shingles begin several inches above the low slope? Is there something wrong with it being only one inch away??

[@ronschlegel6396]

@Catherine Zetack not a disbeliever just a roofer who’s been doing it a long time

[@ronschlegel6396]

@@jban4457 what I’m saying is the membrane should be at least 8 inches above the transition and the shingle start a minimum of 2 inches from the transition

[@donbill8913]

Hello, can I apply the Flintlastic SA roof on the existing garage metal roof? Thank you.

[@liaroozendaal4186]

It would be good to see to a video of Flintlastic and curbed skylight installation.

[@12vLife]

Approved for Florida? Any non-nail base peel and stick underlayment direct to plywood option? split release option is really nice!

[@TBrownRecords]

You made a cool video keep up the good work

[@IkeBlessed-gx4vq]

Can I get it here in Nigeria

[@giovannycruz2725]

O thought of roof didn't have enough slope you couldnt do peel and stick?

[@dancooper3066]

how do you install and waterproof a skylight on an existing torch down flat roof

[@terryjoestoll]

How come the mid base was not applied over all of the nail base before the mid cap was put on?

[@jaydena713]

Is this type of under lament still available

[@markworley1452]

Excellent instructions. Five stars

[@AntonioPerez-dy1ww]

Nice Roofing work

[@brokenarrowez]

The commentator says ,It's an easy installation and then says don't attempt to install this product without proper training. Folks, it's not an easy installation. Look at how many workers are needed to control and install the material.

[@kkp4297]

trust me, you can do this yourself, one person on a simple flat roof. The split release film allows you to lay it flat, and just pull the film from under it. I did my own roof with flintlastic . You don't have to fold it back so high like they do in this video.

[@chuckshipley9917]

Silly, why not just fully adhere 0.60 mil EPDM down. One piece. Done.

[@jakesamaganis4123]

Yeah or TPO. They just wanna compete I guess

[@peterandkodiak9762]

@@chuckshipley9917 Not so easy. That is because EPDM is supplied in ten (10) foot rolls which are 400+ lbs.

[@chuckshipley9917]

@@peterandkodiak9762 My supply house has 20' wide rolls and they will cut the length you need and deliver.

[@user-od4op6ng9y]

Thats some quality work right there

[@jiddex2119]

Safety is Shocking

[@YoMamasCasa]

Oh give me a break!

[@vadadofthr3357]

Can this be applied over an existing rubber roof?

[@LuisReyes-jc1ei]

Se usa brea caliente como en mexico

[@elvisabduli9646]

There you go with that OSHA noise lol. If im doing roll roofing there's no way im roping off.

[@duniagarcia3505]

Ala hora ni le pasan ese rollo por la prisa de terminar luego

[@NorthEastReleafLLC]

I can't find this product anywhere

[@ponchis1966]

I found this at my local roofing supply

[@jamesderoc6717]

what is the life expectancy

[@GerardoLopez-bv9mh]

Probably 25 years + with coating

[@ponchis1966]

I just bought the 3 ply and it has a 20 year warranty

[@JonathanSHoover]

Good roofers

[@merelcroon6878]

What about a roof

[@merelcroon6878]

How long would this last on a roof

[@okiedoke6373]

It seemed like it might be a good product but all the important stuff you covered up with an illustration that really wasn't illustrative I'm going to go ahead and have to pass

[@-mejor-que-nostradamus-6152]

Wasting Your Time 200 Dollars Roll Covers 100 sq ft And Home Depot Liberty Is 200 sq ft with Better Quality 89 Dollars. Amén.

[@russelleaves5435]

i prefer to nail my base down. any suggestions on a good base sheet that i can nail down where the cap sheet will adhere to it?

[@eagles2156]

junk

[@lisaln3987]

Why is it junk? I'm about to have this installed