I see from your video that you appear to be building the engine up indoors…what type of inducement do you use to stop the wife kicking off and ultimately being in a bad mood for the rest of the week?
@romainquiban54692 жыл бұрын
I was all by myself in my student room, problem solved ;)
@nathanrivers43358 жыл бұрын
I always smear oil on the rings, barrel small end etc... No one?
@kieranregan85987 жыл бұрын
will bed in rings better assembling dry
@ShakalJC9 жыл бұрын
Hi, great videos mate! Thanks a lot! I have question, what thickness of cylinder base gasket you use? I got three thickness, so i was wondering what should i use? Maybe the thinnest one? Thanks!
@romainquiban54699 жыл бұрын
Hi ! I use the thinnest one (0,3mm) to get closer to the recommended squish of 1,5mm. In fact with the 0,3mm gasket I have a squish of 1,7mm. If I put the 0,5mm gasket I would have a squish of 1,9mm, etc... More you reduce gasket thickness more you increase torque.
@ShakalJC9 жыл бұрын
Romain Quiban Thanks man.. Yes, as I think so.. I put thinnest one, so i'll see what's going to happen.. I'm not going to measure compression space, but i'll see when startup engine how it's going to sound, power output, etc.. Thanks for info anyway.. Great work and videos. You done job well, like a pro. :) Keep great work. And.. what camera did you use for filming?
@romainquiban54699 жыл бұрын
ShakalJC Thanks ! I use a Gopro silver Hero3+ Good luck for reassembly
@sergillopiscerdan98694 жыл бұрын
😦👍 ¡Excelente vídeo!
@racerracer13669 жыл бұрын
Great Video. Best I've found on youtube for showing a rebuild. Quick question though, what are you using in the syringe? Is it just some lubrication to allow better movement or is it some special stuff? Thanks.
@romainquiban54699 жыл бұрын
Hey thanks! Yeah it's just oil engine (motul 710 here)
@racerracer13669 жыл бұрын
Romain Quiban okay thanks!
@2strokerides Жыл бұрын
Hi, howmuch should the piston ring end gap be? The manual states 0.05 - 0.2mm but that seems a bit less to me.
@alexanderx339 жыл бұрын
this music sounds like emancipator.
@ondotrua12356 жыл бұрын
5:42 but you have not used the torque wrench
@kierankay1002 жыл бұрын
Is it possible to wire a rev counter to this engine
@herobo1234567 жыл бұрын
nice vid
@Biconnecc2 жыл бұрын
Can you change the piston without dropping and unplugging the whole engine?
@Biconnecc2 жыл бұрын
Never mind I saw the answer down below on another comment.
@Vruuzex7 жыл бұрын
can any 1 help me pls iv got 1994 sem aprillia rs rotax 123 (ingnition icu coil is broken) 4 wires red/green/black/and 2 into 1 red,white strip i changed coils but which wires go were? on High Performance Racing HT icu Ignition Coil thxxx
@marcocerioni83535 жыл бұрын
mi risulta che non abbia messo la guarnizione tra cilindro e testata.
@Puzzicanello9 жыл бұрын
I love ur videos and i watched all of them but, you rebuild all your engine and use the old piston?
@romainquiban54699 жыл бұрын
Thanks man, yeah the piston and the cylinder were still good
@mcngt12824 жыл бұрын
If cylinder and piston is in good condition, its only waste of money to change them to new ones. 2 stroke piston can take many many hours more than you expect. If you know even little about 2 stroke engines you can have great and long driving times with them :D
@iDomos9 жыл бұрын
What kind of piston do U use? I think the manufacture name.:)
@romainquiban54699 жыл бұрын
Vertex :)
@adamcarroll23664 жыл бұрын
so many options of pistons on the market, especially @pjme. How do you know which one is best for your application? planning to go 34mm carb w/supporting mods...
@scottmc26459 жыл бұрын
Question. Did you use any gasket between block and the head. or is it just o-rings ?.
@romainquiban54699 жыл бұрын
Scott Mc it's just an o-ring between cylinder and the cylinder head
@scottmc26459 жыл бұрын
Can I do this rebuild with engine in frame ?
@romainquiban54699 жыл бұрын
Scott Mc The four cylinder nuts are very hard to remove because of the frame, you will need a shorten spanner. And that's just the beginning, after there are snap rings to remove and put back without loose it, etc ... In my opinion it's better to remove the engine from the frame. You'll work much more serene.
@SuperDenkoo8 жыл бұрын
how much roughly will cost to rebuild top end of the engine? Aprilia RS 125
@toobzfpv82798 жыл бұрын
Depends where you're at (Currencies are obviously different) but PJME stock piston kits for around 120GBP (Piston, Rings, Gudgeon Pin, Little end roller bearing), a little more coin if you're after OEM stuff
@SuperDenkoo8 жыл бұрын
+TOOBZ FPV 120£ ain't bad at all, I thought it's around 200+. Thanks bro
@waskichanel91298 жыл бұрын
year ?
@gowengetter45993 жыл бұрын
New rings on an older piston?
@romainquiban54693 жыл бұрын
I think i kept the same rings
@gowengetter45993 жыл бұрын
Oh 👍 Do you know what a good squish measurement is. Also a good compression limit on a piston?
@CHEEESBurgerMAN9 жыл бұрын
Did the engine run after ur rebuild? :D
@romainquiban54699 жыл бұрын
works like a charm :)
@danieldalmat75919 жыл бұрын
I dont think so. You forget about 1 gasket (oring)
@romainquiban54699 жыл бұрын
The cylinder head o-ring is missing in this video yes. I put the sequence that I also use in the video of squish measuring, where the o-ring is not needed. No worry, the o-ring has been settled for the real reaasembly :)
@danieldalmat75919 жыл бұрын
Good. I like yours movies. Help alot.
@oae1006 жыл бұрын
So ein Pfusch, eingeölte Fussdichtung auf frisches Silicon? So was hab ich noch nie gesehen! Und warum einen alten Kolben eingebaut?
@bencecseresnyes83075 жыл бұрын
,, So ein Pfusch" Ich möchte dich sehen, wie ist die richtige Arbeitskwalität bei dir. Bitte auf dem gleiches Niveau! ;)
@davidtoh834 жыл бұрын
I got lot of questions to ask...can we email or watsapp?