Being relatively new to all this RC, and having chosen the Kraton 4s - Arrma say ‘just 8 screws needed to remove front and rear diffs’ and manual gives no clue on step by step guide on how to do any of this in a sensible order. Exploded diagrams are probably useful to those who know. This is the only source of information which is absolutely invaluable for people like myself who are still learning. Thank you so much for this, I have saved to refer back to. Will sub. 👍🏻
@ELValenin4 жыл бұрын
My first car was one that no one else had. I basically took half of it apart replacing the main gear because I didn't know which screws to take out...
@imonfire95564 жыл бұрын
Same here bro. I wish there was more vids like this. This was a TON of help!!
@KayakFishing443 жыл бұрын
This is GOLD to noobs! What patience. Great tutorial man.
@stepbackjack41945 жыл бұрын
Are you kidding me? I just got a Granite and Jims bearings are soon to be delivered. I got on the utube looking for the 411 and here you are...within hours. Who knew? good job Mr RazorRC.
@RazorRC5 жыл бұрын
nice!
@xxpug_unicornxx1845 жыл бұрын
Worth noteing while you have the diff out to check the oil inside
@wackpackxj4 жыл бұрын
I could be wrong but I think there’s a bearing literally sandwiched between the slipper set. So maybe you missed one! Idk. But I am glad you shared this video. What bearing kit did you use and how are they holding up? I want a set that will be easy to repack.
@vidsemat55865 жыл бұрын
Thank you for guide. On video you haven't change bearings on HD input gear. Trying now and it's nearly imposible to remove that bearing
@RazorRC5 жыл бұрын
Vida Sematoniene you mean the one at 9:32? That one was super hard.
@vidsemat55865 жыл бұрын
@@RazorRC Not this one. In the Diff there is HD input gear Part number "AR310873" this gear is with 2 bearings. One is easy to take but the second one took me nearly 2h :)
@billyhighfill4 жыл бұрын
great video very detailed and informative! i appreciated the extra info displayed on the screen!
@mtclimber85105 жыл бұрын
Thanks for taking time to do the "hands on" tutorial. Lots of detail, highly informative, and very much appreciated!!
@RazorRC5 жыл бұрын
Appreciate the kind comments! Hope you find it useful!
@steveo20091003 жыл бұрын
Hi how did u take the bearing off the drive shaft as I could not get mine off ?
@balslammerracing14balser954 жыл бұрын
Why move the shims In The diff bearing ? Why ?
@jonvarga55693 жыл бұрын
The Fast Eddys bearing kit comes with a 15x21x4 bearing for the "gearbox" that I cant figure out where it goes. I didn't see you use it. Did you have any left over?
@jorehaast98873 жыл бұрын
Isnt that the one that goes over the driveshaft?
@mikensam5 жыл бұрын
Cool vid cheers. When you say the bearings go bad in the power module fast so check often. How fast is fast? My son has probably ran 4 packs through his granite so far but all working fine so unsure when to do the bearings
@mikecabardo4 жыл бұрын
Is the WD40 Specialist Dirt and Dust resistant dry lube PTFE a suitable replacement for the PB blaster garage door lube? Thanks for this!
@andreasjonsson8075 Жыл бұрын
I use grease in the gearbox. Seems to catch alot of dirt
@EXTREMERC4165 жыл бұрын
Nice but soes it make a differance in the steering?
@RazorRC5 жыл бұрын
Frees it up so there's less drag. I noticed the stock plastic bushings wear and become deformed.
@austinjp19954 жыл бұрын
Seriously a life saver I'm new to RC and wrenching was the most intimidating part. You make it look easy and I appreciate the video to show us beginners a thing or 2 so we don't break things lol. Would you recommend swapping out the bearing before I ever run it?
@nolanconner18503 жыл бұрын
i guess Im kind of randomly asking but do anybody know a good website to stream new series online?
@rickbadessa48975 жыл бұрын
Razor will you end up with continuous diff problems if you don't move the shim to the other side
@RazorRC5 жыл бұрын
The diff shim is used for manufacturing tolerances, if it's too tight or binding move it to the other side, if not, leave it where it is.
@DaVeHiLl2005 жыл бұрын
Tiny barings are in with the Senton kit. They not for the steering bells, these are smaller... where the hell do they go?
@RazorRC5 жыл бұрын
probably motor bearings
@DaVeHiLl2005 жыл бұрын
@@RazorRC nice one buddy I didn't think of that 🙂👍✌
@adamjackson64734 жыл бұрын
Great video Razor rc, all bearings done, had one left over though with a small lip on it, any ideas??
@RazorRC4 жыл бұрын
do you have a Granite/Outcast? The Senton and Typhon use a bearing on the longer centershaft.
@adamjackson64734 жыл бұрын
@@RazorRC Kraton 4s, i put the bearing on the driveshaft, was wondering if there was a bearing behind the pinion gear in the motor
@markhaines71094 жыл бұрын
According to the exploded view that one goes inside the spur gear which can be taken apart.
@Atown8045 жыл бұрын
What is the trick to getting stuck bearings off? Also what kind of grease do they use inside the diff holders?
@RazorRC5 жыл бұрын
Adam Johnston which bearing is stuck? I use silicone grease on the plastic ring/crown gears of the diff holder
@drrogue5 жыл бұрын
Razor RC I guess he meant “stock”
@boogerglob12344 жыл бұрын
Thank you for sharing this video for the bearing replacement! You mentioned "I didn't do the bearing inside the slipper, and having done it I would recommend NOT doing it. It's not worth it and won't go bad since it's completely enclosed." I am assuming the bearing that took approx. 10 minutes to remove was one of the bearings in the slipper, but I could be wrong since I do not know anything about this truck. If the original metal shielded bearings will need to be replaced eventually, I will wait a few months before I tear the truck apart to replace all the bearings with Fast Eddy bearing kit. I bookmarked you video for future reference when the bearings need to be replaced. Take care...
@marcmonge37044 жыл бұрын
No. The bearing he talked about not replacing was INSIDE the slipper. The one that's a pain and took 10min should be replaced as they wear quickly.
@bequiakt4 жыл бұрын
Hey what power hand tool are you using?
@seanmcpherson79624 жыл бұрын
Dude! How to wrench videos are gold for us noobies. And platinum for us blind noobs(me)!😁
@rcpatapouf5 жыл бұрын
Interesting to see how it's made
@kingaj794 жыл бұрын
How did you remove the spur gear bearing (the one that took you 10 min). I gave up!!!!
@ChrisLey4 жыл бұрын
It was easy to remove. My disintegrated on the 8th run.
@sportspallunkerhunter12044 жыл бұрын
I can't find the rear steering servo
@outbackrcaustralia48955 жыл бұрын
Great how to vid mate 👌 How about a video on the slipper clutch set up!?
@RazorRC5 жыл бұрын
Good idea, I need to do one
@seanmcpherson79624 жыл бұрын
@@RazorRC oh please! Any how too on this is great!
@ineedajoint4 жыл бұрын
where does the flanged bearing go on these 3s cars?
@g3t0wNeD4204 жыл бұрын
If its a single bearing and its the same size as the slipper set its the center bearing for it
@nickokesa20475 жыл бұрын
What size bearings are used for the steering Bellcrank
@xxpug_unicornxx1845 жыл бұрын
5x10x4 - youll need 4 in total for the bellcrank
@cwatson427855 жыл бұрын
Hey razor great video! I'm buying to kits from that link for both my 3s granite and 3s typhon. Hey what kind of screw gun is that? Thanks for the help as always.
@RazorRC5 жыл бұрын
It's a Metabo DB3DL2. Used to be called Hitachi.
@cwatson427855 жыл бұрын
@@RazorRC thanks razor and big thanks for this video! Added to rc playlist. I've never replaced bearings all round so this will be a great reference when I order the bearings this weekend! Also one last thing do you have any tips for remembering what size screws go where? I noticed you just remove and put in a pile. Is there any special way to remember what size screws go where or is it just cause your experience? Also one final question and I won't bug you lol. Should I put better oil in the diffs while I have them out? Like silicone oil instead of the grease it comes with? If yes do you have a weight recommendation? I really appreciate your help bud.
@FearlessTrailhawk3 жыл бұрын
I came here to see how the carrier? bearings came off the shaft...but you take those off off screen so i'm guessing its supposed to be easy...but it is definitely not coming off easy at all for me. Only used for 2 weeks!
@Tuidkskiwjdhdbd3 жыл бұрын
Im a dummy i was changeing my input gear on rear diff that I stripped and I pulled my bearing apart I didnt use a big flat head instead i did the genius thing of usung pleers to pull the bearing into pieces so now ordering a kit
@meadowlarkgal255 жыл бұрын
Are you a Marine? It looks like a rifle disassemble-assemble routine!
@RazorRC5 жыл бұрын
hahaha, no, but I'll take that as a compliment!
@islandrc-duke19725 жыл бұрын
great job well done video brother
@denniss78055 жыл бұрын
I actually work for Jim from Jimsbearings, Be sure to check out our Ceramic Hybrids! Use them with your diffs and our Chrome Steel for your hubs and you’re ready to ROCK.
@denniss78055 жыл бұрын
Interested in possibly hearing more? Message us on our Facebook @ Jims Bearigns! Ask for Dennis!
@juanmarichal2635 жыл бұрын
Very useful video, thanks for it 👏👏👏👏👏👏
@philthyco15 жыл бұрын
Fun stuff bro..I love working on my rigs!
@GreatLakesRC5 жыл бұрын
Cool video! I like wrenching videos 👍
@Dylan_50005 жыл бұрын
Not gonna lie but that looks like a pain 😂
@RazorRC5 жыл бұрын
it truly sucks to take everything apart just because the manufacturer is too dumb to put in rubber sealed bearings
@Itsarealone3 жыл бұрын
@@RazorRC would it be worth getting the ceramic sealed over the standard sealed ones?
@TonysRcTechboom5 жыл бұрын
Fantastic build video bro 👍😁👍
@RazorRC5 жыл бұрын
thanks, appreciate it!
@edwinsantiago76395 жыл бұрын
Just installed the same bearings in my senton,is it normal to have tight mesh in the diff after installing these bearings?
@trentmarlowe76555 жыл бұрын
Definitely a worthwhile exercise. Just a shame you have to. 👍