Here is the video that many were waiting! Thanks to our robotic friend Matthew, We will show you hot to apply our film on a curved corner without cutting into the corner. Be careful and follow all the steps to the end.
Пікірлер: 127
@donlunn7922 жыл бұрын
The voice over sounds like a 1950s BBC presenter. But nevertheless a damn good vid. Now I know how I’m going to change my Kitchen cupboard doors. Thanks for the vid and great explanation .
@ARTESIVE2 жыл бұрын
thank you!
@Keddemann Жыл бұрын
I thought the voice was Microsoft Sam
@Gecko12396 Жыл бұрын
I did this tonight for something in my bfs van. Except I used my hairdryer to stretch and it come out perfect! Thanks 😊
@ARTESIVE Жыл бұрын
great
@ARTESIVE Жыл бұрын
it's okay, also the hairdryer is fine!
@kumiko4295 Жыл бұрын
Thank you. It's very helpful
@jamesolelo44065 ай бұрын
So like any corner you just have to be careful and take your time lol glad I learned to do this on a car before building my own tables and drawers to wrap
@ARTESIVE3 ай бұрын
we are happy for you!
@ladybugbecca8 Жыл бұрын
Super helpful! Thanks!
@oummouhamed2529 Жыл бұрын
رائع كنت أبحث عن الطريقة الصحيحة ووجدت هذا الفيديو ساعدني كثيرا بارك الله فيك وشكرا
@ARTESIVE Жыл бұрын
thank you
@LittleLikeness2 жыл бұрын
Brilliant solution with the heat gun for more edge control..thank you for this solution!
@ARTESIVE2 жыл бұрын
Hi! Thank you too!
@justconcentrate98432 жыл бұрын
From my short but very successful experience with wrapping, I heat tension even the flat surfaces for a strong bong. I stary exactly as you with peeling off a small amount and folding but after the first initial full stick of that amount I move forward with heat tensioning the rest
@frasertones85192 жыл бұрын
My bongs are all strong.
@MGmirkin Жыл бұрын
My dongs very strong, too... [/sarc]
@ARTESIVE Жыл бұрын
thank you for your comment.
@jamesolelo44065 ай бұрын
@@frasertones8519mine too😂
@konradwarsiewicz52572 жыл бұрын
Great video thanks
@ARTESIVE2 жыл бұрын
our pleasure!
@blogJM Жыл бұрын
Thanks chat!
@Keddemann Жыл бұрын
What temperature should the heat gun be on?
@shekhargolapkar90742 жыл бұрын
Thanks. Very usefull tutorial.
@marshannajohnson85842 жыл бұрын
I feel cheated! I really would have loved to see how you put the film on the back side of the board. To see how you cut the film to make it look uniform
@ARTESIVE2 жыл бұрын
check better, on final video we also show the bottom face.
@andyp9095 Жыл бұрын
Or you could watch the video again, and this time with your eyes open
@malteserjones1502 Жыл бұрын
@@andyp9095 😂
@lafleurk3727 Жыл бұрын
@@ARTESIVE you didn't show the back side process.. we see something perfect but dont have any idea of how to get a so beautiful finish
@debbiepoulter3790 Жыл бұрын
@lafleurk watch their curved desk video which shows you how to do the finished side. That's how I've just found how to do it.
@cinquentakhamseen3124 Жыл бұрын
Wow! Thank you 😊
@ARTESIVE Жыл бұрын
thank YOU!
@secession772 жыл бұрын
Great tutorial! Will this method work on a board with rounded holes inside? I want to wrap my radiator cover somehow. I think it would be much easier to hot tension all those holes than trying to trace and cut out the foil.
@ARTESIVE Жыл бұрын
hi, thanks. then , this is up to you. we suggest to test first in some part and then decide if this applications can be fine for your case.
@user-qz6ix7od3b Жыл бұрын
how did it work out ?! facing a similar issue. i will use heat to mold the film into the creeces, i don't know if this solution will last over the years though ...
@secession77 Жыл бұрын
@@user-qz6ix7od3b I gave up the idea of using the vinyl wrap at all. The adhesion was too weak on wood material.
@user-qz6ix7od3b Жыл бұрын
@@secession77 yeah, this just looks to be a short term solution. although i think it will last 2-3 years if applied properly, until i get the chance to remodel
@davidcatanach2620 Жыл бұрын
Cheers!
@gregsanchez35532 жыл бұрын
Thanks for your tutorial on how to, Can I apply it to a painted but sanded surface and clean or I have to apply it with putty filler? thanks and Regards Sir Reed
@ARTESIVE2 жыл бұрын
Hi, I didn't understand. If it is already filled and sanded, just use a primer before applying the vinyl.
@heavenscent70011 ай бұрын
Hello I have an ikea cabinet door that is mdf. There are little parts that has already bubbled because of moisture. Can i still salvage it and cover with contact paper?
@superduperboyx Жыл бұрын
Nice video but I really wanted to see how you did the BACK part in connecting with the edge.
@user-qz6ix7od3b Жыл бұрын
would have loved to see that too. did you maybe see any other vid that explains properly how to do corners and edges ? thx !
@manmangy7 ай бұрын
Excellent
@ARTESIVE7 ай бұрын
thank you
@s.o343 Жыл бұрын
Is this film the same as contact paper?
@adilh712122 күн бұрын
oh you are good
@mianbilal33978 ай бұрын
Best job
@ARTESIVE7 ай бұрын
thank you
@josephyeomans1347 Жыл бұрын
Beautiful work! Haha
@ARTESIVE Жыл бұрын
thanks
@shelyb36303 жыл бұрын
exilent
@4tsixer8 ай бұрын
Good vid, but it is a lot different when you cannot move the counter top into different positions.
@ARTESIVE7 ай бұрын
needs a bit of experience. yes.
@jamesolelo44065 ай бұрын
You can't put it on another table and slide it to where you need to? Must be big or heavy
@bribeavers4262 жыл бұрын
Could we use a hair dryer instead of a heat gun? Thank you.
@ARTESIVE2 жыл бұрын
absolutely.. anything that creates hot air is fine.. so also an hair dryer
@lpainter8008 Жыл бұрын
What if you have an inner curve on L shape desk that is also angled, about 30 to 40 degrees rather than a 90 degree edge to the desk top?
@gxvq Жыл бұрын
I have the same question!
@user-qz6ix7od3b Жыл бұрын
i would also like to know a proper workaround for this
@spaceunicorn84232 жыл бұрын
Hi, thanks for the info. Would like to ask. Can it be stick on a plywood or mdf board door.? Do i need to sand it and apply primer before applying this vinyl film?
@ARTESIVE2 жыл бұрын
Hello. Yes it is better to sand it before.. On MDF surfaces we suggest to smooth the surface before apply the vinyl and use the primer especially on corners or edges, such our Magnum Primer for example. You can find it on our official website artesive.com
@vemulanagalakshmi163 Жыл бұрын
@@ARTESIVE Can I purchase the vinyl in india ?
@qwertandrew87203 жыл бұрын
Can u make a video of how u apply the other side without seeing the attachment? Thank you
@ARTESIVE3 жыл бұрын
what do you mean exactly?
@qwertandrew87203 жыл бұрын
@@ARTESIVE you showed that how you install the first side along with corners. At the end of the video, you flipped over to show the other side without describing it. I wanna know how did you cut the edges without seeing the attachment.
@aminasheikh55452 жыл бұрын
Nice
@ARTESIVE2 жыл бұрын
thank you
@McrAwSugarMCR2 жыл бұрын
Hello! What temperature should we be using for the heat gun! Thank you!
@ARTESIVE2 жыл бұрын
The temperature used depends a lot on the film, the distance and the work you are doing. Generally a temperature of 150-200 °C (300-400 °F) is used. However, it is possible to use a normal hairdryer, the time will be longer due to the lower temperature.
@THEGRAVOID Жыл бұрын
Just a quickie, What temperature should i set the heat gun and for how many seconds? Hehe
@ARTESIVE Жыл бұрын
normal temperature is about 150°C at normal distance, but it depends also about time you warm and distance.. make some test and find your ideal setting.
@andersjohannsen70910 ай бұрын
Where can i buy the table overlay? Nice video - xx Anders
@ARTESIVE3 ай бұрын
Hi, check www.artesive.com/
@noteprom81712 жыл бұрын
It's really help me!
@ARTESIVE2 жыл бұрын
thank you! we are really happy about it.
@hessulipoika132 жыл бұрын
Should you put some nails to really lock to vinyl on cabin?
@ARTESIVE2 жыл бұрын
well, at the moment it's still there in right position without any nail.. maybe you are used to low quality vinyls.
@queeniesharpe303 жыл бұрын
What about if you have curves and grooves in the middle of your doors I.e panelled doors
@ARTESIVE3 жыл бұрын
Hi! Try these tutorials: kzbin.info/www/bejne/gXbCeWVvrJqbZ68 and kzbin.info/www/bejne/gH6alWh6rcZqbLs
@queeniesharpe303 жыл бұрын
@@ARTESIVE thank you that's really help full
@user-qz6ix7od3b Жыл бұрын
@@ARTESIVE thank you !!!
@RelaxingSounds-mj5mx2 жыл бұрын
Can i share this perfect video?? It is really helpful!
@ARTESIVE2 жыл бұрын
you can share the link, not copy the video or use for other reasons.
@EbenezerTetteh-tl4yh11 ай бұрын
God reaching bless you ❤
@ARTESIVE3 ай бұрын
Thank you!
@joandr33592 жыл бұрын
Can i remove film like this from MDF furniture? Or else can i paint over it?
@ARTESIVE2 жыл бұрын
Hello, normally on our adhesive films is possible to paint over, to remove that is easier using an heat gun or hairdryer.. warm air helps the detach.
@joandr33592 жыл бұрын
@@ARTESIVE Thank you!
@yourdaddy3812 жыл бұрын
What is the thickness of the vinyl paper?
@ARTESIVE2 жыл бұрын
Hi "my Daddy" , thickness is about 220 microns.
@MGmirkin Жыл бұрын
That AI-generated voice is **almost** believable... **Almost.**
@ARTESIVE Жыл бұрын
almost yes.. important is to understand the video
@Sunnysike Жыл бұрын
what's the film name and where can I find it ?
@ARTESIVE Жыл бұрын
A R T E S I V E all available on artesive.com
@kannancv Жыл бұрын
Ente ponnu sire , veedu evida , table kondu varatte !
@binodgurung33672 жыл бұрын
What if the surface is curved as like that of shield of captain america
@ARTESIVE2 жыл бұрын
beside asking Iron Man, we should see how is the shape to answer you better. Please send us an email and we will reply you better.
@donlunn7922 жыл бұрын
You mean using it on compound curves ? I would think that if it works on that fairly sharp,curved corner a compound curve would be easy,using the heat gun. I have to update my kitchen cupboard doors, and intend to use it on them.Every corner is a compound curve. Even on my old kitchen,the covering on the corners was beginning to de -laminate,where there was any heat.So even professionally made cupboard doors can have problems.But I am sure after a couple of failed attempts I will get the hang of it. Cheaper than replacement doors. Similar film is used on Cars ,and compound curves come in abundance on vehicles. Give it a go. Hope all goes well on your project. Don.
@leonida60242 жыл бұрын
Can I use a hair dryer instead?
@ARTESIVE2 жыл бұрын
hi, of course yes!
@auauseattle2 жыл бұрын
How do you do the other side?
@ARTESIVE2 жыл бұрын
Hi, what do you mean with "other side"? We show in this video the detail of full tensioning application..
@markcook85265 ай бұрын
You sound like Hanable off of Silience of the Lambs!..Say Hello Carisse
@ARTESIVE3 ай бұрын
we'll get over it
@jaby13363 жыл бұрын
Can we use blower here
@laurasayuriamzah17852 жыл бұрын
Up
@jaby13362 жыл бұрын
@@laurasayuriamzah1785 Yes, we can. I was able to do it using blower. 😊
@laurasayuriamzah17852 жыл бұрын
@@jaby1336 thank you so much!
@oneandxero2 жыл бұрын
JARVIS what are you doing here ? 🤔
@stephenhamilton9791 Жыл бұрын
This is definitely one of them random things u go to do. Buy a heat gun, all the materials u plan to use and realise it’s actually like trying to speak fluent Chinese after 2 half hour lessons
@ARTESIVE Жыл бұрын
actually my chinese is quite fluent..
@ranjanapant90843 жыл бұрын
you can go to 3:42
@angturil3 жыл бұрын
Same voice as controllertech lol
@kingabdolbig4306 Жыл бұрын
look at the surface line of the sheet and the side sheet it is not straight. to be honest it would not be acceptable. please use professional
@danielwilde96018 ай бұрын
Found it useful till you didn’t show the next step of applying the back
@ARTESIVE3 ай бұрын
Hi, maybe we'll show it in the next tutorial
@jco997 Жыл бұрын
I still see large bubbles on it. 👎🏿
@ARTESIVE Жыл бұрын
ok, where exactly?
@isabeldiago70712 жыл бұрын
It is not useful my. Table its attached to the wall to work easily on the whole other extreme that is cuved
@cheshirebowman44659 ай бұрын
Great visual video with a diabolical robot voice that just ruins it all. I turned it off.
@ARTESIVE7 ай бұрын
that's the future.. AI.. sorry for the voice..
@cheshirebowman44657 ай бұрын
@@ARTESIVE 🐑🐑🐑🐑🐑🐑🐑🐑🐑
@ARTESIVE7 ай бұрын
was a test.. we will do better in future.. @@cheshirebowman4465
@megamorphe2 жыл бұрын
"Spatula" 🤣 couldn't finish the video because of this stupid automated voice you here on all low quality content.
@ARTESIVE2 жыл бұрын
hi there, beside the voice over, is this video helpful for you?