Artillery Sidewinder x4 Pro - Fast 3D Printer with Linear Rails

More info at: www.artillery3...
✎STL FILES:
Fox:
www.printables...
Dog:
www.printables...
Helicopter:
www.printables...
Tolerance coin:
www.printables...
Test cube:
www.printables...
Vase:
www.printables...
Flexi cat:
cults3d.com/en...
3DBenchy:
www.thingivers...
------------------------------
✎MUSIC:
Music from #InAudio: inaudio.org/
Infraction - I'm good (Positive rock)
------------------------------
✎3D PRINTER: Artillery Sidewinder X4 Pro
------------------------------
✎FACEBOOK: / 3d-printsbuilds-101348...
✎INSTAGRAM: @3dprintsbuilds
✎TikTok: @3dprintsbuilds
✎Cults3d: cults3d.com/en...
✎THINGIVERSE: www.thingivers...
#3dPrinting #Timelapse

[@mikeskerritt9618]

HI it looks like bit of a deaster. Have Artelpry cured these problems yet wint a fewer freeware release.

[@artmanstudios7037]

Well it doesn't seem like at least much to desire seems like it has a lot of Error problems!

[@Perkeletricksterservantofrher]

5 : 42 You saved my printer print bed so you earn a sub. Thanks bro appreciate your warning and guidance. Do you think it's mandatory to grease the rails or do they come pre greased ? I forgot too and had a 24hr print on.. will it damage ?

[@3DPrintsBuilds]

Hi. Thanks for the sub! I greased it after I assembled it, because it felt dry. You should grease after 500 hours of printing. It's written in manual.

[@arda-sh8qx]

Hello. You were the first channel I watched that neutrally listed the disadvantages of a product. Although the Artillery Sidewinder x4 Pro may seem like a good printer on paper, the disadvantages you mentioned in the video cannot be overlooked. I'm planning to buy a new printer these days. There are two printers I'm torn between: the Artillery Sidewinder x4 Pro and the BambuLab A1 Solo. Buying the Bambu printer might financially strain me. Which printer do you think I should choose? Would it be right for me to put myself in financial difficulty by purchasing the BambuLab printer? Is the Artillery Sidewinder x4 Pro sufficient for hobby use? Also, I'm open to other printer recommendations you may have. Regards.

[@3DPrintsBuilds]

Hi. If you have the money I would buy Bambu Lab A1. But if you want something cheaper I would choose Artillery Sidewinder X4 Pro, but I would wait until there is firmware update available. You can watch my other review videos. Maybe it helps to choose your 3d printer. You could also watch Sovol and Creality printers, but if you want same fast printing speeds you need to pay more. Also thanks for watching and have a nice day!

[@arda-sh8qx]

@@3DPrintsBuilds Thank you, have a good day !

[@redrocker1582]

Hi, I've got this printer over a week ago. First prints were very nice, but the more I printed the more quality dropped. As this is my first 3d printer I didn't really know what was wrong and why it failed so much. It turned out that I have to level it again, so I started doing it, but It's fcking impossible. It's absurd how difficult it is to level this printer. Can you give me some tips how to level it? I've found out that no matter what z-offset I'll set with a new firmware (from 19th march), once I tighten the knobs bringing the bed up to the nozzle, the printer ignores the z-offset I've set, because with every new print it goes to home position, checks for bed height with a nozzle and ignores the z-offset I've set to not let me scratch the bed. No matter how high I'll place the bed with knobs and how low I'll set the z-offset, even under the bed, the printer just ignores it. What do I do?

[@3DPrintsBuilds]

Hi, Leveling seems to have problems. Try to level again like I mentioned in video. I haven't used new firmware, but I had similar problems with old firmware too. It seems that it's not fixed with the update. If you can't fix this issue with leveling again, you can add brim to prints and adjust z-height when printing brim. It's not a good solution, but it can help. You can also contact Artillery support.

[@redrocker1582]

@@3DPrintsBuilds I decided to get rid of the printer since because if there are so many issues with leveling right out of the box then what will it be like in the future? Got myself a bambu lab p1s. I've heard it's really reliable. We'll see...

[@3DPrintsBuilds]

@@redrocker1582 I have Bambu Lab X1C and I like it. After TH board change I haven't had any problems.

[@redrocker1582]

@@3DPrintsBuilds Why did you change it?

[@3DPrintsBuilds]

@@redrocker1582 First versions had TH board problems. Bambu Lab sent new.