ATORCH DL24P 180W Electronic Load Tester

In this video we test the ATORCH DL24P 180W Electronic Load Tester
Affiliate Links:
ATORCH DL24P 180W Electronic Load Tester: amzn.to/3JQAvPb
================
CONTACT: [e-mail]
Business/Collaboration only. Please do not contact me for for personal project help, or advice.
If you need help join diysolarforum.... I'm active there, and many other knowledgeable members are available for help.
================
DISCLAIMER: These videos are documenting my own projects, and experiences. These projects, and activities can be dangerous. Do not try any of this at home, doing so will be at your own risk.

[@RinksRides]

so when the vreg for the 3.3V dies, don't waste your time trying to find a replacement. Just jerry rig a new voltage regulator in there. Left pin=GND, middle=Vin, Right=Vout. Your welcome. It's the little black chip center above the screen just under the black bracket for the heatsink.

[@BradCagle]

Thanks for the tip!

[@FixingWithFriends]

Thanks for the run through.

[@BradCagle]

You're welcome

[@mannyfragoza9652]

Im thinking on getting this exact unit. Thanks Brad

[@tatkosmolko1672]

Hi bought day before at official ali shop atorch for 35 dolls . Good to put some heatsink to shunt resistors and maybe even doubling diode or using more powerfull one and changing power transistor for better one. Have a nice day.

[@BradCagle]

Thanks for the info!

[@stevepr100]

Hi, also purchased this (reviewed by others) beauty & been OK with it for about 30 or40 cycles....... The all I'm getting is ureg flashing on dispay😢😢 Any ideas people🤔 much appreciated if anyone knows a solution🙏

[@tatkosmolko1672]

@@stevepr100 Hi i dont understand your problem with display but my unit falls down from table and display was bit weak, when i pressed displey down to mainboard, it shines as original. So i put hot glue small in all corners. So try to lightly press down the displey, mybe its just bad contact.

[@stevepr100]

@@tatkosmolko1672 my bad.. I didn't explain correctly, where you can change from CC CR etc on display top right ish, all that mine shows are the letters (ureg) and I can't access any settings at all.. 😕

[@tatkosmolko1672]

@@stevepr100 Ah so, never heard about problem like that. Only what i can imagine that UREG means , that U - Volts nead to calibrate. You can calibrate device against good known devices. You can reach settings of device by longer press of Start butt and there you will see many things in options. I have Setup version of DL24 V5.1. Its only for DC. Not other what i know to help you. And write if you will solve the problem. I wish you good luck :)

[@reneeccrn]

Love your video, but, your barn door is open. 😊

[@BradCagle]

LOL, Thanks :)

[@ccwstraightshooter9761]

If I’m testing my 768WH 12v power station for capacity, what CC in amps do I set it at and what cutoff voltage?

[@Inshahub]

great job man. thanks.

[@BradCagle]

Thanks!

[@daltonsband]

Could you use this on a larger battery like a valance?

[@BradCagle]

Yes

[@daltonsband]

@@BradCagle Thank you sir

[@simont8757]

Would this pull 25A on 2S battery?

[@leeoliver2969]

I think you should only take the battery down to 3.2 or 3 volts at the lowest.

[@ruudvollebregt5855]

Hey... very good video. But my attention keeps getting taken away because your fly is open.😳

[@BradCagle]

LOL, yeah I have this problem all the time when I wear jeans. Thanks!

[@briangriffiths440]

The app 'looks a little janky'. WTF does that mean?

[@BradCagle]

The app is low quality, unpolished IMO. It'll serve it's purpose I'm sure.

[@TheLittleBikeShop143]

What is the app called