Audiopipe APCLE-30001D - BigDWiz Amp Dyno Collaboration!!! 3,000W RMS @ 2 ohms

[@wal]

Awesome vid guys, except for that bald guy's part :-P . Seriously, thanks for allowing me to provide test data for you guys! Keep it old school!

[@Qualitymobilevideo]

Dude it came out great! We were so stoked to finally do a collab with your channel

[@bobdodge3171]

Who is this big D guy?? 😆😆

[@brentb5303]

smoking it audio pipe! Nice.

[@deborahcaulder7561]

Bigdwiz is this going to be a a monster on 2 skar audio 12evl

[@shawnbroyles8274]

Big d the only reason i clicked was to see your hot rod it was in the thumbnail you need to do a video on your car last time you sat a amp on the running board and i was like show more if the car!!

[@louiemares1610]

Two Great channels to great guys with a lot of experience in audio keep it up guys and thanks for all the schooling you do learning more one video at a time

[@carlosaguilar8321]

Always wanted to see what this amp could do on a dyno test and really exited to see what it does now amazing amp thank you guys

[@Qualitymobilevideo]

Same!

[@ianprice9376]

Nice. Man every time Big D test the audiopipes makes me want one even more. They seem to do rated and some sweet amps. Thanks for the video guys.

[@Qualitymobilevideo]

Agreed!

[@TheHateuguys]

I repaired one of these and when testing it at the end it shook everything in my shop. Crazy power!!!

[@pauljiron7786]

I just saw your post that u repaired 1 of these amps...i just bought 1 hooked it up was hitting fine then i locked up my sub and my amp went into protection mode and it won't do anything else..i bought a new sub and rebooked the amp and nothing just red led on protection can u help me fix it

[@TheHateuguys]

@@pauljiron7786 if no smoke came out and it is in protect then your output mosfets might have burned. The only way to know for sure is to open the amp and test them. If you have basic electronic knowledge you need a multi meter and test the two last lest of the output mosfets. If any of them read zero ohms or beep continuously in the continuity setting then it’s a bad mosfet and needs replacement. This is a simplification of what could be wrong but from my experience it’s usually the case with these.

[@jessewilkinson2534]

U repair amps

[@TheHateuguys]

@@jessewilkinson2534 yes sir

[@LuxorVan]

I see they made some changes since I had my 1600 watt version which actually had a 1500's internal board! They switched the output transistors to TO-3P/TO-247's from the TO-220/50N06 mosfets they used to use! These boards are actually pretty thick as well, compared to other brands and the traces hold up pretty well! Really surprised they actually strapped two amps internally for the design, but that would explain the 2-ohm minimum impedance since each one internally is rated at 1-ohm!

[@catch22frubert]

Nice video. The collaboration with BigDWiz was excellent. This amp is pretty close to my Orion Xtr 2500.1 in power and price to performance. Thumbs up for that!

[@josephharvey289]

catch22frubert how is that orian i here it got hot and cut off.. but do it bump

[@StrangeDuck]

wow, an audiopipe doing rated? are they watching people do dyno tests? hope more manufacturers follow this trend

[@kasper6285]

I am running that amp on my 2 nemesis audio 12s. They hit hard I'm satisfied with the amp. Glad to see it does well in testing.

[@kasper6285]

Nemesis hectic 12s

[@Qualitymobilevideo]

nice setup!

[@kasper6285]

Also using 0g wire extra car battery but I think I need better alternator. Hard finding higher power alts for a 2018 vehicle. Its dimming the lights. Any info on capacitors vs battery let me know trying to make the set up more stable.

[@user-sk5cv7hj2m]

I'm building a nice rock geared system for my car and I bought that amp on sale last year but never installed it. I had no idea it put out that much. Guess I need to upgrade my subs and my alternator.

[@todddooley793]

Saw this video linked to BIG D so I had to check it out, Big D is great! Cool video, I was wondering why they rated this amp at 2ohms, now I know, 2 amps strapped, cool. But dang its a monstrosity.

[@sm9798]

I know this is a couple years old, but investing in a couple good power supplies if he hasn’t! There are some good ones out there can be placed together for more amperage. Megawatt has a 50a version that is stackable for up to 300a. And they aren’t expensive. I’m sure he has all this type equipment by now, but it never hurts to at least pass along some good info.

[@mallorycainjr.1921]

Gotta love all the power at 2ohm I bet it sounds clean

[@shonmar1650]

It definitely does

[@joshshift]

its not 1ohm stable because its just two of their amps strapped together in one big amp.

[@PBwalker]

👍

[@knuckleuprambo]

Josh Cook yepyep

[@meezyosama]

I’ve Ran One Of These At 1 Ohm No Harm

[@jessiewing8199]

Dumb

[@fallofthezombies1379]

@@meezyosama bet u didn't do it for. Long did u?

[@2010HarleyDynaFXD]

It's a 16 volt capable amplifier I wonder what it would run at 16 volts?

[@thebassgeneratorinc229]

I like the output of these APCL series amps and do great in my installs. Now on another subject, I know that a lot of people hate the Epsilon products but the Power Acoustik EG10k was blasted by a lot of people but I am looking at proce verses output, this APCL3k dynamic current draw was over 400amps while producing 4600plus wattage at a 2ohm load but when the EG10 drew 360plus dynamically while producing 4700 plus wattage at 1/2 ohm with no issues....it was called a junk and a few other word's thats no better in description. 😊...and it comes with that 1/2 ohm warranty that most don't. please jelp me better understand why it is being trashed so openly while others are not as great ln the dyno get better reviews?

[@thebassgeneratorinc229]

please dont get me wrong, I love the pipe but I also love and use the power acoustik products as well.

[@sansantos75]

I bought it .. the 3k audiopipe & I'm happpppyyyyy.. pushing 2 12's skar vxf"s .. hitting HARD!

[@Qualitymobilevideo]

Nice!

[@Purosanluispotosi]

@@Qualitymobilevideo they are 3000 rms

[@FinsleysCustomCarAudio]

My head unit is 2v pre out Would that put my gain on amp around the 11:00 position? APCLE 3k

[@bigbobbrown8635]

I was hoping someone would do a dyno test of this amp. I have one and I love it

[@carlossanchez8135]

What radio u run it on . I got boss elite 320watt . Would it work

[@michaelf.2449]

@@carlossanchez8135 get rid of that trash head unit its gonna put out clipped signal def not gonna be a clean signal

[@TeamJesus515]

Congrats on the collab BigDWiz👌

[@Qualitymobilevideo]

Got another one coming!

[@jessewilkinson2534]

How would it do with two of there 18s

[@randywatson4870]

If it's Audiopipe it's real power no invisible #'s..... I got 1 Audiopipe on ice for my future build & 1 on the way to install in my Daily Slider a.k.a. daily driver.... Thanks for this D-Whiz i knew i should have copped 1 when they were plentiful online!

[@michaelzernie7092]

I just bought this amp yesterday😀😀😁 starting the new build in the new van. Cant wait!!

[@Qualitymobilevideo]

BEAST!

[@generalkickass6385]

What a collaboration nice video like always big d wiz

[@keomajones7985]

Great amp it burn up tow kicker l7 and 2 sound stream 12" wired to 2 ohms and the gain was a Lil over quarter it was connected to 3 .marine boat batteries

[@dlopezchampion8054]

Was wondering if you had a recommendation. I just bought a AudioPipe TXX-BDC4-12D 12 Inch 2,200 Watt High Performance Powerful Dual 2 Ohm DVC. I am having a hard time figuring out what amp to pair up. It is in a Qbox single 12" ported. I was wondering what amp will push its peak without blowing the sub. Any suggestions?? Thanks

[@Qualitymobilevideo]

You need an amp that will do 1100 Watts RMS at 2 ohms. Here is a good option: www.qualitymobilevideo.com/audiopipe-apcle-18001d-1800-watt-class-d-mono-amplifier.html

[@dlopezchampion8054]

Thank you I was actually looking at this amp

[@iceman45ification1]

Beast of an amp!! 😮

[@majorwilkesjr.5827]

I have an Audiopipe 2500. I'm curious as to what the actual power rating on that would be on a dyno.

[@johnargue2977]

Looks like it's being tested with over 15 volts. End result at 14volts. So if it's in car with 14 volts, turn it on and it'll drop to 13 volts?

[@tatert.v.9908]

Thats cool dude!! Im glad you guys a re link ing up and I really liked the blue car intro big dummy!! I mean Big D wiz!!! Lol

[@woodsrs5]

I ran this amp at 1 ohm on 2 hdc3 15's. It slammed pretty good until I upgraded.

[@sansantos75]

Had this amp installed in February & it's still going hard. Pushing 2, 12" skar vxf 1500 rms & 3ooo max!.. not strap-able would've been awesome to have 6 + k watts

[@Qualitymobilevideo]

BEAST

[@FinsleysCustomCarAudio]

Santito 4 life still using amp?

[@sansantos75]

@@FinsleysCustomCarAudio yes still using audiopipe 3k.. still hitting hard.. why?

[@FinsleysCustomCarAudio]

Santito 4 life because I just got the APCLE 3k and love it. I have proper electrical and not going under 2 ohm. Basically just curious on longevity of the amp. First audiopipe ever owner. So far I love it.

[@sansantos75]

@@FinsleysCustomCarAudio true it's a powerful amp .. Bad part is , it's not strappable .. but there's ways around that.. I think the new 3k that recently came out is also not strappable, just 1ohm stable

[@804_REESE]

I have ran them a 1ohm and they do good . I had 4 of them on 4 18s did awesome

[@tommygunns3488]

Do you have video of the set up

[@paulcherry1520]

Did u run it at one ohm ? One sub?

[@804_REESE]

Paul Cherry ran 2 at 1 ohm then 4 at 2 ohm. .5 dB difference have one right now at 1 ohm on 2 bdc4 15s.

[@804_REESE]

Tommy Gunns look on exo’s Channel

[@marvinavalos6384]

Yeah I hear that auto pipe is a budget amp good price thanks @bigDWiz..like all the test in u do..

[@bigperv685]

Ok can this amp push 4 quad stack audiopipe 12" with power

[@marioweathers1102]

I got my amp today I'm happy Ap 3000 its going down yall

[@Qualitymobilevideo]

HELL YEA PLAYA

[@justinbertie2146]

I had a Skar rp2000 wired at 1/2 ohm (not recommended) to a zv5 but blew the amp and for a temp amp I installed the audio pipe 3000 but it doesn’t have near the power of the Skar, both gains set with a oscope, any ideas why it don’t make a lot of power before clipping?

[@matholmes4764]

Not as good build quality

[@pork.t.v9462]

Do they last I got two sundown 15 sa d4 and they bang!! I get 147 dbs and no alt or battery just a 5 fared cap boss lol

[@diegomaradona418]

Because you do not do the 14.4 volt test?

[@rc121crx]

That is a great deal for the amount of power its throwing 😎

[@ElectronicsForFun]

WOO COLLABORATION!!!!! and with BigDWiz. OOOOOOOOLLD school stereo. where is HiFi vega? he needs to see this.

[@resaalynn8923]

I have this amp big d and it keeps shutting out(protection light) comes on wen bass note drop I have it hooked to 2 skar audio evl 12 inch 2 ohm subs I have also installed a Extra battery in the trunk have a zero gauge kit the radio even shuts out even with the amp turn all da way down

[@mykejonesjones1846]

Resaa Lynn check your grounds and also check all of your RCAs ? Sometimes bad rcas can trigger a protection..,

[@brentb5303]

Big ''D'' the OG. Its got a ring to it. Nice video.

[@thenotoriousrvh6091]

Collaborate and listen Boston Jim and Big D Wiz taking care of business audio pipe pipe baby

[@scataxoriginal8234]

I run it at .5 ohm to two soundqubed 18s in a 12cuft. Enclosure. With four 6in. Prescion ports

[@gerrodtrice5825]

Hey do your amp cut off .u are talking bout the apcl 3000 amp right?

[@scottfarque7222]

Do I need to run dual power and ground to my 3000 audio pipes with 4 extra batteries

[@rowboyto156]

going by gp car audio i would say yes. they have a video here showing gains of a 1/2db compare to a single. as for batteries, 1 should be good with a 6 pack power bank. its less stress on the alternator than charging up 4 batteries link to that video: kzbin.info/www/bejne/i163pYWgqNmpjJY

[@rz9708]

I wonder what the power is at 8ohms

[@lukelovesbass3738]

Can this amp be strapped?

[@kaycee9337]

I'm just wondering what it'll do at 12 volts 2 ohms. Looking for your input Big Beat

[@randyhay4740]

Your vehicle is producing 14.4v. The battery is 12v.

[@kaycee9337]

My name producing 14.4 V is a Mazda protégé 5 13.5

[@orldmunoz88]

I got one on the trunk of a 2014 corolla and it's great pounding

[@KGZAG2012]

Would it be ok and safe to run this amp on standard car electrical 14v stock ? i only know of a couple of people who compete that actually have a 16v system out of 100s...Please advise, thanks...

[@Qualitymobilevideo]

You'll probably be fine running it at the 4 ohm load. You may start the amplifier running 14v at the 1 ohm load

[@KGZAG2012]

@@Qualitymobilevideo It just disturbs me that it says 16V right in front of the amp APCL-30001D mono im currently running a CAB1600.1 @ 1ohm on all stock Audi electrical with no signs dimming...?? Thanks for replying as well any help or advise is GREATLY APPRECIATED before i melt or blow something up LMAO...

[@blaineblaine7776]

Should of done a 1 ohm burst. If the 1500 and 1800 can handle .5 ohm all day long why not test at 1 ohm?

[@Earlburns1976]

would u get the same with 2 apcl 1500s strapped

[@Qualitymobilevideo]

For same power results, I would guess yes based on the performance of the 30001D

[@randywatson4870]

Big D i wish you would, Bench test more of the cheaper brand newer model amps like from power acoustik soundstream,crunch etc.... Cause they #'s be super duper invisible LoL....

[@1280spoon]

Now they have a 1 ohm version of this amp love the audiopipes

[@Qualitymobilevideo]

Realllyyyyyy? Can you comment a link?

[@alfacilities426]

We run them at 0.5 ohm at 16 volts

[@1280spoon]

@@alfacilities426 wow man

[@CarltonRoberts]

Amma getting one this Amplifier in the near future..thanks guys for the video upload 😀..

[@fresh55n9ne]

Is it a class d mono block amp or class a/b 2 channels

[@Qualitymobilevideo]

Monoblock

[@fresh55n9ne]

Quality Mobile Video only if it was 1 ohm stable

[@brandonscott7029]

definitely one of those ones that you weren’t expecting from audio pipe love mine its a beast Anyone know if you can strap them together thinking about picking a second one up

[@georgehampton6984]

if there is a slave option yes u can

[@Scotty23]

Can someone do a nemesis amp they’re always for sale or dB drive wdx

[@mikemarcum4887]

I know its not 1ohm stable. But i still wanting to see if it will smoke lol i have on gonna try and wire down to 1 and let this box take it back to about 2 ohm see what happens. If any one has done it please let me know

[@HifiVega]

Boston Jim and Big D deathmatch! Make it happen 😁

[@ElectronicsForFun]

amp vs amp. who has the best equipment? FIGHT!

[@ruikazane5123]

Yeah! You're the referee!

[@cobrawannab1]

Test the Rockville RXM-S6 Marine/Boat 6 Channel Amplifier or the Power Acoustik RZ1-3500D mono amp!!

[@marioweathers1102]

Very nice amp I'm buying one soon as possible.

[@Qualitymobilevideo]

www.qualitymobilevideo.com/apcle-30001d.html

[@fallofthezombies1379]

We all have our personal favorite company's that we like and like to hate on. But sometime the haters show u up and make a believer outta you. But not this time for me.

[@Papz2theDome]

They are huge down here in Latin America

[@bigperv685]

Hey can I run 4 quad stack audiopipe subs on this an get good power

[@josephcockheran4923]

Could you do the audiopipe mini 3000

[@Bassotronics]

I guess this amplifier is out of the question for those short circuit people who like to drive amplifiers at such a low ohm load.

[@briank3799]

If I have a 200 amp alternator how many batteries would I still need to run to power this amp

[@rowboyto156]

one battery in the back and one of those 6 pack power banks but if youre in a tight budget a battery and big 3 should be enough, you just cant bump it hard/ max volume for a long period of time

[@jamilporterterry1392]

Rowboyto what is a 6 pack

[@stevojohnson8997]

Can this amp push 4 15inch kicker cvx

[@Qualitymobilevideo]

Do you have the 2 ohm or 4 ohm subs

[@stevojohnson8997]

I have the 4ohm subs

[@Qualitymobilevideo]

This amp is actually solid then because Four DVC 4 ohm woofers get wired to a 2 ohm load and the amplifier does 3,000W RMS @ 2 ohms. The only problem I see is that those subs do 1,000W RMS each, and ideally you want your amplifier to either match the RMS of the subs or have a higher rating for head room. But so long as you don't push them too hard you should be ok. Another option would be to get two amplifiers with a rating of 2,000W RMS+ @ 1 ohm, because you can wire two DVC 4 ohm subs to a 1 ohm load. Might be a little safer

[@stevojohnson8997]

@@Qualitymobilevideo thanks and I'm just gonna go buy two 2500watt brutus elite 35th anniversary or a 4000watt hifonics brutus elite 35th anniversary... which one do you think I should go with?

[@rowboyto156]

@@stevojohnson8997 none, hifonics inflates their numbers. id go with 2 wolfram c-2400.1 amps. its been dyno tested and proves that it pushes their claimed watts

[@patricksimpson4700]

Have this amp on 2 american bass xr 15s it awesome

[@Qualitymobilevideo]

👌

[@ruikazane5123]

Big D's out there!

[@electromechanicalstuff2602]

Itd literaly just 2 of their 2000 watt amps strapped together already in one case

[@michaelzernie7092]

I have this amp. Alot more money than this guys said. But it was worth it. Pounds the hell outta my subs

[@_itskane]

where do i buy one of these amps

[@Qualitymobilevideo]

From us! Free shipping: www.qualitymobilevideo.com/apcle-30001d.html

[@RobertoRamirez-rg2co]

@@Qualitymobilevideo still available?

[@kylosolo8815]

I have a ap1800d and it does the job

[@CruzRacing2]

Want to know what it puts out @ 1ohm

[@Qualitymobilevideo]

Not stable at 1 ohm

[@jimcoleman52]

smoke. it puts out smoke at 1 ohm.

[@scataxoriginal8234]

I run it at .5 ohm to two soundqubed 18s im a 12cuft. Enclosure. With four 6in. Prescion ports.

[@izaakavenaluckyss1933]

Lots of love for Big D Wiz

[@Qualitymobilevideo]

The man!

[@mike4you508]

Test the earthquake 2500 2nd gen please

[@mykejonesjones1846]

This amp can do almost 5K at 15v to 16v ??

[@Qualitymobilevideo]

About 3,000W RMS

[@rdooski]

Audiopipe has alot of haters but I ran a strapped pair of mini 1500's for a couple years in the south Texas heat and had 0 problems. They have some of the best cheap amps out there IMO.

[@Qualitymobilevideo]

Agreed! Underrated gear

[@mykejonesjones1846]

rdooski Yeap! Not everyone can spend 1500-3000 thousand on a amplifier?

[@rdooski]

@@mykejonesjones1846 Was nice and small too. I made little wood amp rack that wast basically a T and put a amp on each side of the piece of wood sticking up. It made a like little 5x14 amp brick. They were the apsm1500 which were a bit smaller than the current minis.

[@michaelzernie7092]

Boom!! I bought this bad boy!!! Bought the wrong subs tho. Hooked up 2x Rockville K6V2. Need to get better subs lol

[@benjaminbaird3798]

So he said it doesn't run at 1 ohm but it does

[@clippingcoils8215]

Great numbers. The guts look beefy. First time I've seen an amp have two strapped inside one.

[@izrael2321]

Big d is the best ,hands down 💪

[@chuckholmes]

its just 2 1500 watt amps bridged internally thats why it can't do 1 ohm. why buy a Class D if you can't do 1 ohm. now you gotta rewire or rebuy your woofers to compensate for DVC 2 ohms

[@Qualitymobilevideo]

Well there are pros and cons, same with a 1 ohm load. 2 ohm is less power yes, more efficient. Some people may be stuck with two DVC 2 ohm woofers and can't make a 1 ohm load, and have to opt for the 2 ohm load, which some people actually prefer. Like all things in car audio, its subjective.

[@mykejonesjones1846]

Chuck Holmes dude it’s just a 300hundred dollar amp most people run them until they can up grade!!!

[@jamesalexander5847]

Can they be strapped

[@Qualitymobilevideo]

The 30001D's can't it only has one pair of RCA inputs. The XTR15002 and XTR1500.1Dz can

[@jamesalexander5847]

Quality Mobile Video gotcha... Thanks

[@marosanchez5650]

300? Where can I get one ?

[@Qualitymobilevideo]

www.qualitymobilevideo.com/apcle-30001d.html

[@jefferyjackson7201]

@@Qualitymobilevideo how much for a audio pipe 3000

[@DJ252Customz]

So diz amp is not 1ohm???

[@Qualitymobilevideo]

3000 watts RMS x 1 Channel (2 ohm)1800 watts RMS x 1 Channel (4 ohms)

[@josephcockheran4923]

Thank u big d try the 1ohm when u can

[@snapcase7364]

Very Inefficient

[@50plymouths]

@400 amps... Jesus it a Power hungry amplifier

[@mykejonesjones1846]

robert wood close to 5K watts any amp is going to draw close to 300-400AMPS

[@mrbasshead403]

@@mykejonesjones1846 Nope I disagree the audio pipe amp is dirty lol it's extremely power hungry because of it's strap configuration. In deed it's an budget gem but it's dirty on power. And running this amp with in proper power supply will lead to it's failure.

[@fatcatt3981]

That's a good looking amp.

[@chriskent3923]

Funny... I run mine on 2 VFL Stealth 15s wired @ 1.4ohm. But I'm probably being saved by box rise.

[@catch22frubert]

I assume you are being saved by box rise, but either way, I bet you still see great power to those Stealths

[@W6p0kn]

Awesome! Finally the video I was waiting for, I have this amp and the triple stock audio pipe P12, dual 2omega. What's the correct way to hook this up? It gets hot at 1ohms and does hit that heavy at 4ohms.

[@Qualitymobilevideo]

Unfortunately, this amplifier is not stable at 1 ohm! Which is why it's getting hot, you're lucking it didn't fail on you/ Wire it in series for a 4 ohm load.

[@MyBlowncobra]

Damn near 450 amps of current.

[@bandpassmess]

Big D needs to get a cut , he does the test right in front of you not literature throw in a box . Been following him following him for a while even does a podcast.

[@joshholden8561]

3k at 2 ohm is extremely powerful I wonder how it does at 1 ohm

[@pork.t.v9462]

Give it away maaytee in thinking of doing an alll audio pipe stuff just cuz its cheeper

[@matthewwoods8241]

omg I love you bro

[@jordanfuhrer4468]

It's not 1 ohm stable because inside it's 2 1500.1 boards strapped.