On setting focal length, I use the Tool holder. It is 50 mm. Place material, jog laser,lower the Z by 1 mm, place the tool holder on material and lower the laser in to contact by loosening the screws, raise up 1 mm to remove holder. Then lower Z to 26 mm for engraving.
@FlyBy2507 Жыл бұрын
Finaly! A laser graver with motorized Z axis 👍
@USMiner8 ай бұрын
Thanks, concise and to the point. This is the 2nd time I've run into your channel looking for laser engraver reviews and yours are the best.
@Reindeer-ry2lf Жыл бұрын
Interesting for a huge work area. It seems like it was Frankenstein build but you as professional make it look like a piece of cake to use. Thanks again for the sleuthing and professional videos 📶💪🇺🇸😎
@kickpublishing5 ай бұрын
I found this invaluable in helping me get my z axis setup sorted, thank you
@Tdog5008 ай бұрын
Thanks for the review. I takes a lot of time putting something like this together, great job!
@jerrodmcdaniel2043 Жыл бұрын
Great review as always. Thank you for all you do to help us to succeed in our everyday task Looking forward to more great reviews from your channel
@MrDaneis Жыл бұрын
I barley have room for a few P1P's... I'd have to get rid of my car to own this thing. Amazing review as always!
@snapshooter659 ай бұрын
Good review and a nice taste of background jazz music!
@chrisduty28869 ай бұрын
Hello, I would like to extend this larger than the optional extension kit. Unable to find the extrusions used in this machine. Could you point me in the right direction?
@KatherineSandersis Жыл бұрын
Always enjoy your videos, and this one gives us a larger view of the machine.Great vid👍
@KnotHead1008 Жыл бұрын
The Bluetooth compatibility is the issue over both win 10 and 11. Most of these builders may have experience with the hardware build, but not with wireless 🛜 hardware. I also find that didn’t provide a cover to block the intense light. Please could do a review of the plotter? Video was 👍👍👍
@aberodriguez4149 Жыл бұрын
Very impressive review as always, thanks for such detail reviews.
@atienne_navarre Жыл бұрын
You are correct. NEJE is HORRIBLE at documentation. I bought the MAX3 and information on how to focus the laser head is all over the place. They even have in house videos on here that contradict each other. I probably wouldn't buy another laser from them because of this. The hardware is pretty good ONCE you learn how to use it which is a lot of hit or miss and searching. Im probably going to replace the variable laser head on the MAX3 with something else even though Ive hardly used it. I mainly bought it for the size anyway.
@KatherineSandersis Жыл бұрын
There are always various ways to focus. It's just that people offer more quality methods than their official ones. I like open design. A fixed approach will make it easier for the user, however an open design will make your creation more remarkable. 😉
@luizaugusto96439 ай бұрын
@AURORA TECH Uma coisa que tambeim notei e que o laser fica ligao mesmo com a opção de 0% potencia isso e normal?
@luizaugusto96439 ай бұрын
Oí amigo necesito de uma ajuda eu comprei uma máquina dessa neje max4 e80 com essa extenção de área de 1030mm e 750mm ontem eu a estalei en lightburn coloquei o tamanho da área de trabalho de 1030 - 750 más en lightburn a direção do láser sai fora da área de trabalho e me choca nas estruturas da máquina poderia me ajudar? Obrigado
@olafb.2929 Жыл бұрын
A good review, as usual. Thanks :)😊
@stvcolwill Жыл бұрын
awesome review. Instantly subbed! great job!
@jeffallen33823 ай бұрын
Were you ever able to find a fix for the Bluetooth problems?
@willyblain189 Жыл бұрын
Hello , thx for your video 👍🏼very useful , Can you tell me the height of your printed block for the rotary feature ? Thank you
@AuroraTech Жыл бұрын
It actually depends on the size of the object you need to engrave, the blocks I printed are 50x50x120mm.
@kickpublishing5 ай бұрын
How did you set the laser height for material tests in lightburn?
@PredragKnezevic-wu4om4 ай бұрын
Kako i gde ga kupiti?Divan je.Cena?Bravooo❤
@nevilenobody606 Жыл бұрын
That exposed laser lol. BTW have you considered doing a test of the available good quality laser glasses other than those supplied by the machine makers?
@milancapik23996 ай бұрын
Hello, I have a question. What is the accuracy of cutting a circle? I had one model from Atomstack, and there the cutting accuracy fluctuated around the circumference by 0.4 mm. It didn't make me an even circle, but rather an uneven ellipse. I want to buy NEJE MAX for the size of the structure, but I am afraid that this problem will get worse. So far, I haven't had a laser other than Atomstack. It cuts the rectangle/square exactly to 0.02mm, but it can't handle the circle. That's why I'm interested in how it is with NEJE, since it has a completely different construction. well thank you
@eherrmann01 Жыл бұрын
Thank you so much for this video. I've been considering a laser engraver but most of the videos that I've found are glorified sales pitches, without much useful information. One of the main uses that I have for one is engraving on hand-turned wood pens. Would I need the rotary roller to engrave on pens that are ~ 15-18mm in diameter?
@peterfabry96872 ай бұрын
I'm considering of bying a Max 4 E80 but in the KZbin video's they have a tankchane on the X and then in other video's they dont....even at the site they show a tank chane.
@peterfabry96872 ай бұрын
Why?????
@bartv6387 Жыл бұрын
Where can i get the brackets for the honeycom bed? Now its a crime working with the MAX4
@arranp1693 Жыл бұрын
How do you configure the lazer to recognize the extension kit? I got one a little while ago but can't figure it out!
@federicowilckensclaussen Жыл бұрын
hi change the 131 value on light burn, just write $131=1030 cheers!
@luizaugusto96439 ай бұрын
@@federicowilckensclaussen obrigada amigo me salvou estava a 4 días varias horas por día e não consiguia alterar gracias a você deu serto! Que Deus te abençõe muito
@alandimery33798 ай бұрын
A great video, thanks. I am interested in purchasing a 20w laser engraver. I am concerned about the noise of these high powered diode lasers. I have heard that the Neje is quieter than most. You never mentioned this but do you think that this is so? Thanks
@user-ly1iq5di3g Жыл бұрын
Does anyone know if the stepper drivers on the control board for this are silent (TMC, etc.)? I've gotten spoiled by them on everything else...
@vinnnocc Жыл бұрын
STL for the 3d printed brackets?
@doctorpd1959 Жыл бұрын
Would you be able to provide the Lightburn grid test files for engraving/cutting (in Lightburn extension .lbrn2) for download please? Thank you.
@avejst Жыл бұрын
20W laser and a Open frame is not a combo I would recommend!
@CrisAnderson27 Жыл бұрын
Loving your reviews. Out of all of the lasers/brands you've reviewed so far, which is your preference? I'm really thinking of going with the Neje. I already have the 3s Max with the A40640...but I'm really wanting to take advantage of the improved power and speed of the new unit.
@CrisAnderson2711 ай бұрын
I bought the NEJE, and the power supply quit within 48hrs lol. The laser itself though is excellent, cutting construction grade 4.5mm luan plywood at 500mm/m-100% one pass. In addition...realignment has been incredible. I can home the machine and restart it at the exact position I choose. The stepper motors stay locked, meaning they don't relax like other machines (or NEJE's old machines), which is what causes poor alignment. In addition homing zeroes the machine to .001mm accuracy per NEJE. So far, I'm inclined to believe them as this was one thing I've tested purposely. Also, I believe the reason that NEJE rates it at 20,000hrs is their much improved cooling system. 100% cooper heat sink and excellent air flow is top of the line.
@jppalm394411 ай бұрын
No where on the site doesn't mention watts. What is 80 module?
@MarcusBuer6 ай бұрын
This is an issue with almost all diode laser engraver brands. They try to use in marketing materials and product naming how many watts the machine uses instead of optical power, to make the customer think the machine is more powerful than it actually is. This machine has an optical power of 20 watts, probably using four 5w diodes.
@JoseHernandez-mj6ne Жыл бұрын
Great review. Can you tell me what’s the best laser engraver and cutter with 60 watts or greater for beginner as a never owned one. Easy to set up and use?
@AuroraTech Жыл бұрын
A desktop diode laser cannot generate as much power. You might want to consider the xTool P2, a 55W CO2 laser: kzbin.info/www/bejne/sGq2eIulpt5shJI.
@JoseHernandez-mj6ne Жыл бұрын
@@AuroraTech thank you. As always I enjoyed your reviews. You are a smart cookie young lady. I see great thing in your future. That’s coming from a Jar head.
@YolandisWorld10 ай бұрын
Damn girl. I wish I had a woman like you in my life.
@tweekFPV Жыл бұрын
👍🏻👍🏻
@pavolkrajcik7675 Жыл бұрын
YOu get like and channel is subscribed long time ago.
@efrenvergara-xq4wl Жыл бұрын
Good video 1st
@TestTest-eb8jr Жыл бұрын
👍🖒👍@Aurora
@Piccyman1 Жыл бұрын
Why are the laser cutters so expensive, there isn’t much on them justifying $1000
@jparniawski Жыл бұрын
Hype and popularity. Same happened to 3d printers.
@miuix47957 ай бұрын
Never neje again ... No service and real criminals