Automatic Pet Waterer

Automatic waterer for pets, homemade automatic waterer of high durability manufactured with PVC accessories, with an approximate capacity of 5 liters, can supply water to your pets for a week without the need for replacement.
Materials used:
PVC pipe 50 cm 100 mm (part where water is stored)
20 cm and 53 cm pvc pipe (works internally to maintain level without overflowing)
2 knees 90 ° pvc 100mm (used to make the bowl)
1 knee 45 ° pvc 100mm (top or water inlet)
1 PVC plug of 100 mm (drinker cover)
1 sheet of EVA (seal)
´´Tips and compliments are always welcome``
´´Leave them in the comments``
If you are not yet part of the pasta, SUBSCRIBE ☞
/ @meantimeentretempo
Activate 🔔 not to miss any of the channel's new videos!
▬▬▬▬▬▬▬▬▬ Social networks ▬▬▬▬▬▬▬▬▬
FaceBook: / entretempo
Instagram: / meantime_entretempo
The Meantime channel has the ´´Do It Yourself`` group on FaceBook and WhatsApp, with the aim of exchanging ideas, doubts and any subject related to the range of leisure and recreation crafts. Participate and share ideas:
Facebook Group: groups/22016...
Grupo N ° 1 WhatsApp: chat.whatsapp.com/IzxkT3Axo5e...
Grupo N ° 2 WhatsApp: chat.whatsapp.com/ISz23K1vVbF...

[@zarlus8]

There are many comments asking how this waterer works. It's only a guess as it isn't possible to see the water level inside the larger pipe. However, from what I can tell the video shows two pipes; smaller inner pipe, (for air) and larger outter pipe, (for water). The inner pipe passes through a divider. The divider at 5:26 has a small hole drilled in the center. This hole allows water to pass through slowly; (due to atmospheric pressure), from the upper reservoir to the lower dispenser "U" shaped area. The divider is placed, (inside the larger pipe) at the same height position as the desired water level for the dog to drink 7:26. This level also covers the bottom opening of the smaller inner pipe. When the dog drinks, the water level drops in the "U" which allows air into the "U" and up through the inner pipe. Atmospheric pressure pushes on the water in the reservoir allowing water to pass through the small hole in the divider. The water will fill the "U" until it covers the bottom opening of the inner smaller pipe which stops the water from filling and spilling out.

[@MeantimeEntretempo]

Exactly

[@zarlus8]

@@MeantimeEntretempo thank you

[@twowheelfarm9024]

It is also very important for the top cap to seal air tight, and the hole in the divider to be small. As it will be running out while you fill it until you get the top cap back on.

[@radamest2]

Thank you!

[@kingkaleem6942]

Is the cap necessary to prevent over flow?

[@jordanjgoldsmith22]

And for those who are still confused how it works… it’s quick, but he first drills a small hole in the center of the divider before making a second hole for the inner pipe/hose. This is where water passes through and the inner hose allows air for the slow distribution of water. So the divider has two holes… one small one at the very center and a second which the inner pipe passes through!

[@thomasmchugh1989]

THANK YOU! I thought so but your confirmation was super helpful. Love this design

[@gustavojimenez7802]

Dont forget it needs to be airtight otherwise will spill the water after a while

[@chickenwhisperer8410]

Yes it looked almost as if he had just made a center mark without drilling all the way through. I figured that it went through but it doesn’t show it very well

[@felinerescue5272]

Nevermind, I'll just buy one.

[@vernonjermin]

😂😂😂😂😂

[@girthworm6895]

I'll just use a bowl thanks

[@sameasnone]

Where?

[@alexanderyan89]

Where to buy can you share the link ? Thanks

[@unveiledwithouttears1370]

You should buy 2, just in case.

[@Ryan62751]

Lol nice invention, I especially love the part when he shows the dogs how to use it.

[@sebytro]

This is awesome! It's a great space saver since it stands vertically and doesn't take so much space on the ground. Thank you.

[@blixten2928]

I love this channel! So cool, no-nonsense, just get right into showing us. REALLY GREAT, thanks!!

[@mynamesnotrob]

That’s clear as mud instructions.

[@busigh]

I like the principle of controlling the water level really cool. I designed my own water dispenser before watching this but incorporated a system to automatically fill the chamber too rather than manually filling the reservoir. Simply I added a toilet bowl all in one fill valve with float and connected it to water supply. My design didn't use his method of controlling the water level at the feeder outlet to the dog either. I created a port and installed a hose on my water reservoir 2 inches below the water fill line and ran it to the dogs water bowl placing it 2 inches below the water fill line. This way the water level in the bowl controls the filling of the bowl and the toilet valve float unit controls the filling of the reservoir. No heating up of PVC (which releases toxic fume from what I read) just drill two holes and attach PVC and you are good. My unit allows for multiple hoses to multiple dog water bowls attached to the same reservoir.

[@davidgraemesmith1980]

I can just about remember when magazines showed diagrams of projects like this 😊 yup I'm old at 41yrs

[@sansan925]

Estaba mirando recetas de cocina y terminé mirando este video. Muy bueno 👌

[@diegofariacarlos]

Muito bom, gostei muito da engenhosidade!! Não faz bagunça e usa toda a extensão do PVC!! 👏👏

[@adamm2909]

Excellent job 🇵🇸❤️🕊 Love and respect from Jerusalem the capital of Palestine 🇵🇸

[@vigneshpadoor2303]

Nice idea and well shown❤

[@drrussdc]

Great application of physics 👏 well done!

[@notwrkn2mch]

We are out in the Arizona desert and i fill a poultry waterer for the local birds, rabbits and quail..... luckily no coyotes yet and your technique would be a much better solution for me.... I need to watch it a few more times to get the concept of why the water doesn't all dump out the bottom

[@josselinelemanach7430]

Un homme qui aime la précision et le travail bien fait, ça fait plaisir à voir !

[@marianam.desousa2341]

HAHAHAHSHHSH catiorada adorou!!! Q trampo bonito!!

[@raven314]

love this design ... easy simple .. thanks Meantime for sharing!

[@elisasalamanca842]

Gracias me ha resultado muy práctico su video..... y me encanta la limpieza de su trabajo....gracias por compartir.

[@c-martz2846]

Brillante amigo!

[@gerlandoalvesgomes94]

Ótimo muito bem feito, e o estímulo ao cão pra usar o bebedouro foi muito inteligente kkkkkkkkkkk

[@alfredodiaz8229]

I think I know what is missing, in the materials I see that one of the small tubes is missing. The big one is the respirator and the small one supplies the water, but in the video you only see how you put on the respirator. "20 cm and 53 cm pvc pipe (works internally to maintain level without overflowing)"

[@jasonmiller5995]

‘Damn, that looks easy”~said no one truthfully. Doc Browns’ dog food dispenser for his dog “Einstein”, was as convoluted as this. Great job though.

[@Dudu291097]

Que engenhosidade daora mano... A idéia tá simplesmente genial! Como sempre, as melhores gambiarras com quem entende do assunto!!! Tá de parabéns mano 🤙🤙🤙🤙

[@MeantimeEntretempo]

Valeu parceiro, você é o cara!

[@cesarmezaycabrera7358]

Idea maravillosa, gracias

[@JoseCarlos-ol5by]

Aí sim... Belo trabalho . São José do Rio preto sp Brasil 🇧🇷

[@MeantimeEntretempo]

Valeu parceiro

[@oldhiway66]

BRILLIANT! Hilarious ending. I think the plumbing industry owes you for making P traps 😆

[@richier.1585]

Good job. Buena idea.

[@elyserva7903]

I think it would be cheaper just to buy the waterer! Saves you the trouble! 😄😄😄

[@funn4547]

So nice! Want to make it but the directions say 2 internal pipes but video only shows one😩. Please explain what did I miss ?

[@jbiliHacker]

3:20 nice invisible watch!

[@suspence25]

Chris Notap should try this one.

[@Skashoon]

Easy if you have patience and tools. I lack both. On to the next video. Great waterer, but it’s too difficult with the few tools I have.

[@JohnB3363]

I would’ve used a clear pipe and put tape down the length of the last third or so before painting it so I could monitor the water level.

[@psyco4916]

Thats a cool idea bro. I figured it out how this works after couple of minutes. Great work bro.

[@bhekisfruitful488]

I'm still lost you know

[@psyco4916]

@@bhekisfruitful488 bro its simple. You see that small hole made by a nail. If you dont close the top end with cap the water will ooz out like gravity action. The small hole prevents quick water flowdown . So you get enough time to refill it. Then you close the top so no air going in so the water flowdown stops. Then when the dog drinks water the water level drops and air can pass through the inner small pvc, the water will flow down untill the water level comes as earlier and hit the inner pvc down end. Phew I think you understood now. If not i will explain again 😅😅😅

[@wushugirl6941]

@@psyco4916 so we should put water in the inner pvc pipe, right?

[@psyco4916]

@@wushugirl6941 no the inner small pipe is for air to pass from botom when dog drinks water. The water is filled inside the main pvc.

[@wayjeen]

@@psyco4916 i watched it 2-3 times and figuring how the water flow down knowing that the overflow pipe is not the one sending water. And i totally get it when you mentioned the small hole by the nail ! Thank you for sharing !

[@rosalbagonzalez4522]

Los perritos😂😂👍👍

[@dani644b]

The end was cool 😎

[@onetruesoldiervt3686]

Nice 👍🏼 job I wish I could make one but seems a lil tricky

[@alefalves4299]

Ficou top irmão, com a crise de corona vírus faça umas máscara para o povo

[@MeantimeEntretempo]

Que ótima ideia em, valeu!

[@Sloansteelsigns]

Do you have the plans for this design?

[@sandubercea9952]

Super

[@jongrubaugh160]

Great idea nonetheless.

[@kubeckunderka453]

Hello, please, must the knee bowl have a 90 ° angle to make the bowl or can the knee bowl be of different angles?

[@valdirrocha3431]

O cano de 25 mm q vc colocou dentro , é só encaixado ?

[@MMFORTAL]

Great

[@L.Salvatore]

Good idea

[@valiyevdavlatbekrustamjonovich]

Good

[@gabrielrissi608]

Top demaisssss

[@yagocorrientes]

vi modelos con válvulas que en argentina no se consiguen... este me sorprendiendo.... el agua cae por el agujero de 2 mm verdad?

[@polesejunior]

Estranhei o título que me apareceu, parecia uma tradução esquisita, aí olhei o título na aba do navegador e vi em inglês, credo, sente o poder do canal!!!!! Hhehehe

[@malukinha7036]

Kkkkk

[@antoniosaraiva9737]

e muito bem explicado

[@jorgegranada4964]

Make it smaller and its a good hummingbird feeder.

[@GonzoDonzo]

They do sell these for about $30. Hooks right up to your hose. With the cost of pvc its probly a better route

[@GreenChilliD]

Link? Keyword for search?

[@SolidworksUnlimited]

Lol that burp

[@woofy548]

a big bucket of water works too and is a lot easier to clean and change the water

[@MeantimeEntretempo]

A tank would also work, but I have no place for one at home ...

[@Reddylion]

Nice...

[@dtec30]

Not sure I quite followed it was it like a bell syphon ?

[@GreenChilliD]

Who doesn’t like tequila? 😂😆🤣

[@Young937phoenix]

You can just buy the waterers that screw into pvc that ends up cheaper than making one of these and works just as well

[@angelortiz9784]

Ive seen many versions of this on the tube, but this one seems more efficient. Would it be possible to replace the copper with CPVC 1/2"? also non of the versions have a way to know when it needs to be refilled. maybe a clear tube version would solve this problem at the same time you could make sure the water environment is clean.

[@MeantimeEntretempo]

I've tried with smaller tubes, but unfortunately it doesn't work

[@swangodesigns]

​@Meantime that's my main concern is sterilization.

[@kathrynw.9754]

Love that music! Who is it? Also the waterer is cool too.

[@alexisyairvalenciamendoza1454]

Es jenial

[@IBMDOCTOR]

Not bad but Water warms up My idea to have flap to drain warm water and debris also mounted to the line

[@sylgibbons859]

👍👍

[@justyalicea2602]

I've built something similar for my chickens. How do you keep the inside from building up algae/mold? I had a layer of green film inside the pvc in less than 2 weeks

[@MeantimeEntretempo]

whenever the slime builds up, I use a hypochlorite solution with water to clean it.

[@sbstoecker]

A very small amount of hydrogen peroxide in the water will help.

[@douglasdishroon1834]

@@sbstoecker Hydrogen peroxide slowly decomposes into water and oxygen. An elevation of temperature and the presence of pollutions enhance this process. This is a redox reaction. Hydrogen molecules partly function as reductors and partly as oxidizers.

[@sbstoecker]

@@douglasdishroon1834 Would you be able help me breakdown then what processes are happening to help reduce algae build up? On the rough, my field study compared the following - A 32 liter chicken waterer, refilled everyday. 3 days at 30 Celsius and there is significant algae growth in the waterer. Now the same but with a

[@douglasdishroon1834]

@@sbstoecker Hydrogen molecules partly function as reductors and "partly" as oxidizers. It's still helping, it's merely less active. Meaning your concentration of H202 could be higher.

[@saidraid9855]

I did the same thing but doesn't work. Is there any schema with what should not to do ?

[@sholland42]

A real hacksaw would have made it much easier. Great idea, thanks.

[@fabianovargas126]

Boa tarde, gostei da idéia só uma dúvida você colou o cano de 3/4 que fica dentro do círculo de PVC.

[@JoseAntonio-yb7yi]

Também tive dúvidas nessa parte,foi feito um pequeno furo no centro da quela tampa cega e um para o cano é isso,o cano 3/4 funciona como o que lá dentro,a água não sai por ele certo,a água sai pelo furo do centro do tampo cego né isso,precisa colar esse cano ou só deixar na forma obtida pelo esquento?

[@guyfisher2050]

Great idea, but not sure all those chemicals are food safe (caulking and paint)

[@sanghpriyverma9845]

Please reply me the cap on the top is necessary ?

[@mikelestad2]

Cumpa la tubería de adentro le hiciste agujeros para que siga llenando el bebedero , o solo sirve como respiradero ? No cache mucho esa parte .. gracias .

[@Jaimeb453]

Creo q se tiene q llenar del diario

[@Jaimeb453]

No se como bajara la demás 💧

[@charjaylorenzo5429]

Do you fixed? Circle pvc inside the tube?

[@babyriver8121]

Es muy buena idea, pero cual es la idea del cobre adentro, si me wxplicas porfavor

[@mustang268]

You did alot more then you really had to

[@jmti1356]

Bonsoir j' ai réalisé le même que vous mais je rencontre un problème : L eau coule en continu - prise d air ? En tout cas ingénieuse idée

[@susannahb2723]

The music is a whole bop at 1.25x

[@ronwillett9014]

Can you get written instructions for waterers?

[@avouzas]

I liked the fact that you put up work for the project but I honestly do not see the need for such engineering solution.... A much simpler solution is the following: Simply keep the outer PVC assembly as is and create a second sealing cup. Then: 1. seal the water output when you want to fill in water. 2. Open the top cup and fill in water. 3. Put the top cup again and remove the bottom cup. As soon as the pet drinks water the air will go to the top releasing water at the bottom. What do you think? :)

[@DanielLaRusso-Do]

What is the exact purpose of the thin pipe inside the waterer? The water is droping through the tiny hole you made in the middle of the flat round piece that holds the thin pipe?

[@MeantimeEntretempo]

The larger inner tube serves as a bridge for the air inside the reservoir to escape and maintain the water level.

[@schumpa17]

You don't even need the small tube in there it serves no purpose. You could have drilled a 1/4 inch hole at the top of the lid and that would be enough for air flow but regardless air bubbles would make their way up the pipe as the dogs drink n the water level will always stay the same cause it's called gravity. You people must not have a lot of knowledge to b impressed n fooled by such a pointless video. Oh n don't worry bout him putting alcohol in the dogs water that's real good n health for their livers. Should be in jail for animal abuse and I'll b sending this video to the aspca

[@mehmetberke5121]

@@schumpa17 Its not called gravity domass. If he had just drilled a hole the two openings of the pipe would have the same atmospheric pressure so all the water he pours in would just spill at the bottom. The mechanism with the small tube keeps the pressure difference. This guys tutorial is worth dog shit without correct display of that mechanism anyways.

[@mustang268]

@@mehmetberke5121"domass" I wouldn't call people dumb if i where you lol and sorry you dont need that inner pipe at all the top cap being air tight is more important and I'm a plumber I know what I'm talking about it will work just as good without it don't care if you believe me or not so dont bother with your childish response either won't read it

[@alexanderyan89]

@@MeantimeEntretempo is there anyway can buy from you ? We need that !!!!!😅

[@antoniollamas6367]

10:16 “You can lead a horse to water but you can’t force it to drink”

[@GreenChilliD]

I’m frustrated. So, I built this. I am having an issue when I close the top. It seals but wont refill. As soon as I open the top it overflows. Is my vent pipe leaking?

[@GreenChilliD]

I think I know what the issue is. My elbows are different than yours. They have more of a drop. Yours are basically perpendicular. My air gets trapped in the elbow at the back because the front has to drop very low before air can pass from the front to the back. I bet if I drill a hole just below the diaphragm and above the bottom of the vent pipe it will fill the front to the top.

[@GreenChilliD]

Yup that did it. Filled right to the brim in the front. Physics 🤣

[@calebwiggins3042]

Should have done that outside with a heat gun cause the pvc just ruined your toaster oven

[@mirfster7425]

Yep, Toaster Oven is now "Toast" for any usage with food.

[@CosmicJib]

I’m a plumber and we don’t use tape for a straight cut we just eye it

[@mmawad100]

If the water does not flow down while the top cap is away Why does it flows down when the cap is on ?, Did any one build that and it actually worked ?

[@sebit2874]

👍😄🐕

[@just2botheru]

But how do you clean it?

[@Th3Crow10111]

Great video mate. I have to try this out. For those that don't get the joke at the end... faq em snitch's.

[@marcelalarroque9378]

Que pasa si no le pongo el caño fino que le pusiste adentro?

[@odairmarquesdealmeida1572]

Faltou explicar como funciona o sistem

[@tubrogg]

Do you have a step by step video of how the water holds inside the pipe?

[@MeantimeEntretempo]

Unfortunately not, but the system is based on vacuum

[@tubrogg]

Do you know where I can find this vacuum concept on KZbin?

[@alfredodiaz8229]

en la lista de materiales falta el adhesivo usado, no parece el típico adhesivo de PVC.

[@heut4384]

I do like your engineering work. It does look very nice. However, I can see, it will take awhile to make just one (i.e., cutting the pipes and otherpieces, gluing, painting, etc.) I would imagined, you may had been working for a few hours....? Especially, you have to be very articulated. For me, I like alittle more simplicity and quickly to changing water, etc. Lol. But, thank you giving us more other option.

[@mustang268]

You dont need to do as much as him all you need was PVC glue he over thank it I built one in 5 minutes but I'm also a plumber so that helps

[@user-ro8bz3vr1g]

🤝👍

[@RomSoloO]

Man, they don't speak spanish, you wrote Agua, that's why the won't drink it 😜 just kidding, amazing inventions, I'm now gonna try at home!!

[@jeffk7626]

i don t understand how it works with the smaller pipe inside.

[@davidcastillo379]

Me either, I wish he would have explained it

[@thehazelnutspread]

I loved it up until you put in the black circle. You could have done a lot more to explain how it works with the small grey tube.

[@pinkmosey]

Make mini one for hamster pls

[@Brunooc0]

Faltou nos materiais a cola.

[@rushikeshmore7260]

In How many days water is dried ??

[@Roady2010]

Amigo no disco de pvc que recortou e perfurou com o cano fininho , o disco é colado por dentro certo? Mas o cano fino só entra na pressão dentro do disco é isso? Sem cola mesmo? O segredo todo ta ali, qi a agua escorre devagar por esse furo no disco? Eu ja preparei a o grosso ai, so falta esse disco e cano fino, ta funcionando mas como um bebedouro de gaiola de passarinho, vedei a tampa superior e avasteço o bebedor de cabeça pra baixo, viro rapido, e a pressão estabiliza kkk

[@evandromax4121]

Não precisa desse cano fino eu fiz sem e deu certo.