700R4 TRANSMISSION FULL REBUILD PART 2

[@robertdevito5001]

You actually installed the forward assembly, reverse drum, and band and then removed it all just to show us how to put it in again from a different angle, respect

[@Marksracingengines]

Man I love your videos. I'm an engine builder and I really appreciate you putting these videos out. I've done a few transmissions power glides and th350's but I dont know much about them. I recently have found myself needing to do a couple of 700's and a 4l60 for my own stuff. man you are a life saver! You have the most complete no BS videos on transmissions on KZbin! Thanks Brother! Also...I feel your pain on voice overs lol

[@littlekorfs1820]

I rebuilt a 700r4 with this video and no prior experience with transmissions thank you so much

[@KirtFritz]

My son and I watched this video together to rebuild his 4L60. Your videos are the best I've ever seen, very informative and fast paced which I like for videos. Thank you very much for your time you put into these videos.

[@mikeeustice4452]

Hiram its so nice to see you back at the bench, been subscribed for years, I hope you and your family are well and healthy

[@derekfromm7094]

This is the most detailed and informative video I've ever watch. Great work!

[@housepumpinpc3983]

Damn...I fell asleep and woke up and you were still at it. This, by far, is the most in depth video I have seen or dreamed(since I slept thru some).MY MAN...

[@richardlewis7471]

Hiram this is a masterpiece! Watched it several times and always learn something new.

[@edwardburke5486]

this video was just what i needed ...i removed the servo and the band moved into the way of the servo pin so that i cant push the new servo back into the case ....2 things i learned 1 being how the band sits in the case and2 how to be able to get to the band without removing the trans from the car to get this issue sorted out ...great video very good instructions all through it all . thank you for going through it for everyone to understand....see how he explains how the band would move and not allow the servo to go into the case that is exactly what happened to me and this video was a very big help to get my issue sorted out thank you so much

[@jmshssk2]

Thank you for your time and effort you put in to educate us. This build seems very intimidating with all those pieces but with you as guide it isnt so scary.

[@mag1vl]

Hello Hiram from the Aussie guy ;) A top job mate and I watched it all , every bit of it and you sir are a master builder!!!

[@AutomaticTransmission]

Thanks Ausie

[@edwardburke5486]

I also had issues with the governor being at first a broken gear that I replaced ... cleaned up the governor with carb cleaner and after installing it it shifted once or twice and was once again stuck in its boar .... I have since ordered a 10mm boar brush that I plan on cleaning up the inner sleeve of the governor in hopes that that will help keep it from hanging up in the future... I also plan in doing a full trans flush to clean out all the old fluid from the transmission and converter...hopefully this will be enough to get this trans shifting gears again like it was just recently, I had no issues untill just recently when the governor gear went any input I’m real thankful for. Great video , great information thank you !.

[@budhardy5853]

Hiram I got yo tell you that your videos were prefect. I'm sitting at my bench and have just finished my 700r4 after watching your parts 1 & 2. I did this trans years ago and followed a guy on a DVD and he took only 2hrs to complete the reassembling process. Your info was great, I found so many mistakes from the first time I did it also. Thanks so much for doing this it was a pleasure getting this task completed and with your help I'll be on the road this spring.

[@georgenorris8603]

I just want to say this is one of the most informative videos I've watched. I'm a veteran mechanic Diesel and gasoline. My first time doing an automatic transmission. This video made it simple for me. Thanks..

[@eldoradony]

I have over 40 years experience in auto repair and the only things I haven't tackled are rear end rebuilds and automatic transmissions. I have a vehicle with a 700R4 that will soon be needing a rebuild so I thought this might be a good thing to watch and learn from, and maybe attempt it myself. What I took away from this video is that to do the right job you can't do it without the knowledge and depth of parts that a pro like you have. You are truly an ace at what you do. If I weren't in New York you would be seeing me soon at your shop. Thanks for taking the time to make your videos. They are great.

[@AutomaticTransmission]

You're welcome.

[@gregorytrimeloni9401]

Hiram, again with this second part of the 700R4 rebuild , my son and I are eager to watch again and again , then get started on out rebuild. You should be an instructor, you explain things very clearly.

[@IamDerick]

That was a video worth (re)watching. The detail you went into was fantastic. Thanks for the effort with the camera and the background noise. Cheers.

[@therustysquash5131]

Really needed this for my 1991 Camaro, glad I found your channel. I was a bit hesitant to even attempt rebuilding my transmission, but after watching this and part 1 I feel much more confident. Thanks a lot, you really know your stuff.

[@outseeker]

how did it go!? :D

[@stevenbarnett5620]

I will watch this video 10 more times and should be ready to build my transmission.

[@williamcoiner6019]

thanks for taking time to get into the weeds on this. Bought a used 700R4 for my 73 C10 but I want to beef it up a little. Now I feel I should be able to tackle it.

[@jimmybaxter6163]

morning Hiram i stopped building when these started and now a lot older and doing some 4l60e s so this was my first full view of 700 THANKS you are great TEACHER JIMMY n ALA

[@AutomaticTransmission]

Excellent, I'll post more variety of units.

[@MHolt3573]

Awesome awesome video sir. Thank you for taking the time to make this video. I'm a younger mechanic trying to expand my knowledge.

[@erictate9891]

Hiram, thank you for sharing you knowledge. I have learned so much from your videos.

[@christopherbetancourt8007]

thank you sir. I finally finished my transmission. i gotta admit this was my first time ever doing this. it took me several weeks due to my lack of experience. i damaged two lip seals and had to order more and the i freakin damaged the pressure regulator valve in the front pump but it was totally my fault. i got frustrated and pryed in a bad location. i got a new one from amazon no problem. your video was very thorough and my mistakes were totally my fault. thank you very much for this video

[@thomasrogers5152]

Dude you rock! At least you got it done. That's awesome and gives me hope I torn mine down last week and going to start the rebuild on my next day off.

[@javieraviles6314]

Great job Hiram . Thanks for the info on all the video that you do . Blessings to you and your Family. Hard times going on , no te aguites hermanaso .👍

[@AutomaticTransmission]

Gracias

[@frankiestein4013]

You Sir will probably never see this But if you do it is much appreciated the extra trouble you go through to show us technical information with a hands on demonstration thank you sir

[@Jeff123456789987]

Great video. Im doing my own 700r4 and using this video and some books. Its a really good video. I said f it and trimed the load spring retainers some.

[@jimlarkin8392]

Great video thank you very much ,I will Veatch it several more times, I learned so much

[@Mike-bj1jj]

Great video! I have a 1992 Chevy pickup with a 700 R4 that needs rebuilt. This was a great educational video. Keep up the great work Hiram!

[@AutomaticTransmission]

Thanks

[@jamesrucker6405]

.m

[@jamesrucker6405]

T......For

[@jamesrucker6405]

@@AutomaticTransmission ..

[@johnteague756]

I know I'm late to the party, but others like me that just found your channel might get this info. In the ATSG Upgrade book, on page 95 they back up and give an explanation on the boost springs . It basically echos what you said, "if you have tight clearances, use the booster springs, they do more good than harm." Just a little info to give to the newbies that didn't have the book or upgrade book. Thanks for your teaching expertise.

[@BMGProjects]

I don’t mind the fan. I say stay cool. You are doing us a favor teaching us. You have every right to stay cool.

[@AutomaticTransmission]

Thanks

[@davidmiller9485]

before the lock down i was telling him the same. I used to live in Texas and it's damn hot there. I would rather listen to the fan than watch him wither due to heat.

[@benzo13]

Watched pt. 1 & 2✔️Great instructions!

[@SPEEDOFDOG]

Don’t mind the fan my friend. Stay comfortable. Excellent knowledge and skills,thank you sir.

[@AutomaticTransmission]

Excellent, I'll try that next time.

[@davidmcduffie1398]

Thank you Hiram ! I've learned a lot from watching your videos. It's not often you find someone who will take the time to explain and show in detail what they are doing ! Thanks again ! ! !

[@michaelhawkins4731]

Awesome video. You help out so many people keep up the amazing videos.

[@craigbasoco4886]

Thank you for this video I rebuilt my 700r4 last year doing fine for now.. my first was a 400 turbo it didn't do good at all the pan exploded..

[@toddkennedy7623]

I really appreciate your videos I enjoy working on cars .I'm building a 92 chevy stepside with 700r4 and I want to rebuild the transmission myself I can do everything else I want to do the transmission to

[@randy1ization]

u may want to grind that mushroom off your bushing driver,., it can fracture and a small piece fall in the trans, and u might not see it. thanks great vid sir!

[@rauleldriver]

Great job!! Hiram very cool video 👍👍

[@JohnSmith-fh5mp]

My transmission just started making wierd noises sounds like its coming from the torque converter. Really have no over drive and all the gears shifts way late i have to floor it for it to shift. I have a spare trans that took a dump 13 months after i paid $2700 to have it rebuilt. Ima take it apart tomorrow and see whats wrong with it.. Thank you for this 1 and 2 part video.

[@billk5727]

Great video!! You can't beat it! Bar none. Bill

[@AutomaticTransmission]

Thanks Bill

[@jameslewis1175]

Taught me a lot about the 4l60e and what showmanship man.. thanks

[@AutomaticTransmission]

You're welcome

[@jmshssk2]

For the bushing install, isnt lt possible to freeze the bushing and heat the part it goes into and just drop in place? My father used to put a ring gear in the over and a flex plate in the freezer and mated the two pieces very easily.

[@sahrawix]

Thank you for your time and efforts. Well Done 💯

[@FabriceDourgnon]

Great video! Can you tell me why you installed the 3-4 accumulator spring first and the 3-4 accumulator piston into the bore with the legs facing down before the spacer plate? I don't think it's mounted that way on mine

[@AutomaticTransmission]

Something we builders know from installing corrector kits.

[@spike64531]

I watched this video step by step as I rebuilt the 700r4 on my 1990 Corvette. It shifts beautiful now, my only issue is when I put it into drive it slams into gear. Did I do something wrong somewhere? Any help would be appreciated.

[@krazobuildz7567]

Used your 4l60e series I would like to see some th400 stuff thanks for all the work you do bro

[@zakaroonetwork777]

Call up B&H Photo and get yourself a Lapel Microphone that clips on your shirt collar. 👍your the best man!

[@nythanorayvri]

Man he explained it very well. If I am studying working on transmission I’ll watch this video. It’s just to much work for me every time I see different tools I get discouraged if live close to this guy I just bring my tranny to this guy get it fix by him.Excellent skills though!

[@AutomaticTransmission]

Awesome

[@chrisland169]

where is the check ball for the aux valve body ,never saw you putting there?

[@jimthomas777]

I fixed my slipping Automatic transmission in about 45 minutes , didn't even have to take the oil pan off or remove any bolts , I just added a pilot bushing , Steel SFI certified Fly Wheel , 11 inch clutch and M-21 Muncie 4 speed , That old automatic don't slip no more

[@TravisClements-i7b]

Would putting another wavy in cause a problem on the last clutch pack before the pump to bring it within .060 Clearance

[@tomsmith2331]

I noticed the bottom bolt hole for the case that holds the pump the case is busted ! Is that a problem!?!

[@kiwisdontflytheyr.v.9962]

This has been an awesome video for me (along with part one) as I work through the disassembly and rebuild process of my 700r4. If you still monitor the questions on this Hiram, I have one. The green seal which is designed to separate the 3rd and 4th fluid, in my kit it was blue, and it seems a little loose to me. I goo’d it up with the green goo, but it only takes a slight knock and it comes out of its groove easy. I have since assembled the drum, I kinda hope it wasn’t knocked and is still seated. Do I need to disassemble and put a tighter seal on?

[@Realest]

Great video i followed all your steps , but im having a problem i installed the tran go kit (full manual) new gaskets , seals and all. i have no first gear , shifting from 2nd to 1st will stop the car. 1st gear feels like i have the brakes on the car doesn't move. any hint what i should check ? thanks

[@alexandretaxijp2671]

Bom dia no 🚖 táxi João pessoa PB 🌵🇧🇷

[@MrAutospec]

Wow! What a precision job!

[@outseeker]

that load release springs cage height issue is an interesting one! did anyone ever reach out to say they're making them shorter?

[@davidmiller9485]

+1 for the Bob Ross reference!!!

[@keysautorepair6038]

Taking apart a 700r4 and it has aluminum pieces in the pan what might that be?

[@DaveHills-m7j]

I am doing a rebuild and the 700r4 I'm doing did not have the flex plate. Is this ok or do I need to get a flex plate for the Rear drum.

[@AutomaticTransmission]

Very early models of 700R4's do not take one. You'll notice that the steel plate against the piston is waved. This is the way early ones come. Also in the forward clutch assembly there's no waved plate. So just take note of it and how you disassembled it.

[@CJ9494.]

So what was the issue with the pump? I have a 700r4 my pump won’t seat flush it will go down until there about a quarter inch gap then won’t move.

[@chregu2]

I have to rebuild a 1983 700R4 which is for a K5 Blazer. Do you recommend a particular brand for the overhaul kit? Thank you for the video.

[@barrykilts4506]

I have a very early 700r4 I assume much the same as this one,what’s it cost ball park,to do this rebuild,more than my TH 350 I’m assuming?I tried pulling a junk 350 apart once and I won’t do that again and I can do the rest of a vehicle.

[@41johndeere]

Thank you for your hard work very informative

[@nickmiller7477]

Thanks so much bro for your videos they're very helpful...

[@castledomeknives9395]

Them LOAD RELEASE SPRINGS are driving you nuts... I also think like you,, I'm thinking of dremeling a bit off the* spring plate*

[@jakelundy4035]

Hey need a little help I'm rebuilding a 86 700r4 30 spline non auxiliary and my pump is trashed I have a 88 auxiliary pump wondering if the pump will work if I block off the oil pipe hole in the pump

[@alexfullmer4707]

Hiram, would it be possible to remove the springs from the load spring mechanism, file or grind off a couple thousands from the spring holders and then reinstall the springs into the holders to give that little more clearance that is needed?

[@AutomaticTransmission]

Yes, that's actually what I do but didn't show it. I use my bench grinder, I remove the top friction and grind the spring retainer until I'm below flush of the steel plate.

[@alexfullmer4707]

@@AutomaticTransmission ah. By the way, thank you for your dedication to put out some VERY informative videos on transmission repair. I'm up here to west TN working on getting a transmission repair shop set up. Your videos are very helpful. Thanks.

[@mayocruise4884]

hey Hiriam do you have a video to rebuild a cvt transmission ?

[@AutomaticTransmission]

Not yet, but there's plans for the future.

[@Bonnachill865]

Please help!!?? Does a 1983 700r4 have a low reverse wavy plate? Or is it just 5 steels?

[@bobjacobs1182]

Hey Hyram, the 700R4 I'm working on has 2 snap ring grooves at the low/reverse sprague support. Yours has 1? 1st ring sposed to hold clutch plates down. Or can I add extra plate and clutch and use 1 snap ring ?

[@bamadave1983]

You can use the low reverse roller clutch and the carriers it goes in out of a 4l60e and it way better than the 700r4 one they make couple different thickness of them plates to get the clearance where you want on the low reverse

[@Bamm1369]

When I apply air to forward clutch it come out the overrun port. What did I do wrong?

[@rippnlips7531]

Why no gasket between the input pump??

[@irredeemabledeplorable5227]

Did I misunderstand a post you made on these check balls, where you said that you only use 2 check balls and have great results?....I don't do enough of these to be confident and, once they are together, i keep second-guessing myself...your vids have helped me immensely, especially that one you did years ago on the 4L80E...

[@ehilerjose]

saludos colega un habrazo

[@AutomaticTransmission]

Saludos Venezuela

[@otrpatriot1980]

Mr Hiram, I watched both of your videos on the 700r4 rebuild and basically followed step by step but used a little bit different parts in an effort to upgrade my trans to hopefully survive behind my 425hp sbc. Now I have a little bit of a problem. My TC will not engage the oil pump. I did upgrade the pump internals to a 13 vane 4L60 pump. Is there a difference in the keyway opening or snout size between the 700r4 and 4L60 TC? Like an idiot, I did test fit the pump bushing to the snout of the TC but I never did test fit the pump.

[@AutomaticTransmission]

What year 4L60E torque converter you're using? 1999 and up are different. You should spin the torque converter in until you can't get your fingers between the converter and the pump through the bottom.

[@otrpatriot1980]

@@AutomaticTransmission the trans is an 88 700r4 and the TC is a 700r4 as well. But like I said, I put the 13 vane 4L60 pump internals in the 700r4 pump housing.

[@otrpatriot1980]

@@AutomaticTransmission welp, I found my problem. I thought I was being high speed by smearing in some blue assembly lube into the pump to protect it on startup. Turns out that blue assembly lube hydraulically locked the pump. I've cleaned all of the assembly lube out and it is good to go now. I had the best of intentions but they ended up being bad 🤦‍♂️

[@AutomaticTransmission]

👍

[@sethpalmer4393]

What specific tools do you need for this rebuild

[@russnolan7519]

Why do they say to grind the land off on the pump pressure valve?

[@caseymoss9247]

I wish you would show the thicker pieces that go in front and or behind the friction disks and steels. I’ve gotten lost a few times and had to go back to before when you were just putting everything sort of together to see what you didn’t show. May have to find another video to see what you didn’t show.

[@casemfduke]

is putting new bushings reqired?

[@AutomaticTransmission]

Yes

[@donataskk354]

Hello. Nice video 👍 do you know what color original spring for 2-3 shift valve?

[@SinghAvleen]

Hi Hiram . I got R700 early built without auxiliary valve body . Some one installed on jaguar 89 XJS and i need some information because transmission has couple valves blocked on valve body .

[@kengvigilia9946]

what about the Ford XLT E150 automatic transmission. how to assemble all parts

[@donaldbrinkman8209]

Great videos, lot's of explanation. I'm doing a 700 for a friend, wondering if you could post a list of all the upgraded parts? The trans I'm doing is a 1985 model,friend is going to install it in a 1970 C10 truck with medium build 350.

[@KoryRude]

Industrial engines class had overviewed fibre plates reassembly THAT when oil absorbs there is a percentage of expansion PER Fibre Plate....so CANT remember 42 years AGO but....I recall..during reinstallation was not DRY if i remember it was installed after pulling fibre plates out of oil and casually touching microcloth absorbing loose excess oil...but cant remember if WE were suppose to install after dabbing technique or if we used gloves to wipe oil on plates front n back.....but I remember...that ONE of the TWO or BOTH was 8n FACT the Proper Technique when installing fibre plates...when measuring clearance...YEPP.😊

[@AutomaticTransmission]

Yeah, they do expand some. I usually soak them then hang them for about 5 minutes and install them. They will not expand any more once they've taken fluid in. You'll also notice when soaking the fibers (Frictions) bubbles in the fluid. Once there's no more bubbles they've taken what needed. Like you said, you'll have a more accurate measurement on clearance.

[@andycoslet6479]

What would cause a 700r4 to loose reverse

[@eddiesheets5136]

Followed your video as best I could. Tranny will not upshift. Tv cable adjusted. Governor checked. Any suggestions?

[@eddiealcala2288]

I'm about to attempt my first 700r4 rebuild thanks to this video!! Great Great help!. Can I use a bearing and seal driver in place of the bushing driver?

[@randy1ization]

could u just take the springs out and grind the metal down a bit?

[@AutomaticTransmission]

That's exactly what I do, I haven't posted that for the fire I'll get from the internet keyboard profesionals. So yes, I go to my bench grinder and grind enough to be below the last steel without the friction installed. I can probably make a video on it, just to Anwar your question.

[@randy1ization]

@@AutomaticTransmission thanks, It just makes great sense, and I figured you had considered doing it. your the one responsible to the customer to make it work and last, so its your call how you do things. good job!

[@castledomeknives9395]

AT 1:05:40 WHAT did he sneak in there? Thanks for the awesome video

[@inthemiddle22]

Is it Normal for the output shaft to turn real hard in one direction?

[@alexfullmer4707]

Now which hole did you put the air to to check for low/reverse leak?

[@castledomeknives9395]

Is it a Good idea to *glue* Them on with 3M yellow??? 2:27:00

[@rolfrykowski6670]

Hello, cool video, I'm going to overhaul my TH700R4 (C1500) after this video! Will be my first automatic transmission! I once learned to be a car mechanic! But I still have a question! Nothing has been oiled but only partially lubricated Doesn't that damage the oil pump if it starts dry and has to suck in oil first? Sorry translated with google Rolf from Germany

[@AutomaticTransmission]

No, but you can wet the pump rotor with transmission fluid for lubrication.

[@michaell8645]

Ok have gone through 2 lip seals and on the third and for the life of me cannot get the reverse drum piston to cooperate.🤬

[@jaymChrist4ever]

How would I have to build a 700r4 to run behind a 396?

[@captainmorgansautomotive9950]

Hiram I was wondering if it is possible to peg out the pump slide to make maximum pressure all the time. Would this cause it to self destruction? Also I've been told that the 4l60e pump rotor kit can be used is this true?

[@AutomaticTransmission]

I don't recommend that on the pump slide, but if your pump slide only has one spring add the internal spring. And yes, you can use a rotor from a 4L60E 13 vane.

[@deluxe707]

These videos are amazing! I have two 91’ 700r4’s I need to have rebuilt. Both will be run with a sbc 350 and 4.11 posi rear end. What’s a good rebuild kit and torque converter I should order and what brands should I stay away from? Thank you 😎👍