A comparison of two new gauges of the same manufacturer.
Пікірлер: 42
@aaroncolombo6 жыл бұрын
Personally i like electric gauges better, those mechanical gauges for one the oil pressure line gets old and brittle and when they blow its usually in car and you have a pressured line shooting oil all over your interior. NHRA doesn't allow them unless you have braided steel lines instead of plastic.
@aaronmorris33476 жыл бұрын
Bleed the air out of the line to eliminate the delay
@mbz46522 жыл бұрын
How do you do that?
@juliogonzo27182 жыл бұрын
@@mbz4652 crack the fitting at the gauge till oil comes out and tighten it. Probably don't want to do that in your interior though
@backyardbuilttrucks12 жыл бұрын
Never had a mechanical oil pressure gauge take that long.
@johnmiller-in5bt Жыл бұрын
its cuz they used a drill ! also probably has never been used yet.
@HeadFlowInc6 жыл бұрын
Ok guys, run the -3 stainless steel braided lines with AN fittings on each end. This will eliminate the possibility of leaks or a cracked/broken oil pressure line. 👍 Merry Christmas! 🎁🎄
@DanFrantzFilms10 ай бұрын
Great vid, clear and to the point. Thanks
@connoisseurofcannabiscarsp37555 жыл бұрын
I daily a 1994 Mustang Cobra and I drive all over the hottest parts of the country.I run EVERYTHING with Mechanical gauges.I run a 3 row Aluminum Rad,Oil Cooler with a finned Morosso 7quart pan..I run a T56 MAGNUM 6 Speed which makes 4.10s no problem plus it allows for 30plus mpg..Anyway I run just over 475HP & 490FT LBS TRQ..I ONLY trust my Mechanical gauges which consist of Oil Temp,Oil Pressure,Water Temp,Fuel Pressure,Water Temp,AF along with Fuel.I do run a full AIM dash cluster but I only because I KNOW I CAN TRUST MY ANALOGS!!!! Keep it real man!!! 👍
@johnelliott737517 күн бұрын
The two at once is not a good comparison but I will say that the mechanical is better every time for there is nothing to fail in the mechanical one. But I think the one is robbing the other one as I found out was the case in the other one. Thanks again and have a great day today
@GREATGARLOOXX6 жыл бұрын
Is there copper tubing that could be used instead of the flimsy plastic line? I've had my leg covered in oil once because of the crappy plastic tube
@mart1820036 жыл бұрын
I thought they came with the copper line, or maybe it's an extra you can purchase. But I have seen the copper wire in an autometer box
@ianbrown58684 жыл бұрын
Yes they sell copper tubes and they are better to use than the plastic
@100reality24 жыл бұрын
Autometer sell braided line for the oil pressure gauges so you don't have any leeks ect
@fistmeetsurface2 жыл бұрын
I love the idea of the mechanical, I'm just worried about that input lag. If your oil pressure does plummet, you wont know for a few seconds. Which could be enough to cost you
@flinch6222 жыл бұрын
A nearly 10% variance is big, but not alarming. A good big [4"] gauge would be nice to reach for to find out where the error is. I have a sneaking suspicion the sending unit is off - as long as error is known and linear, you just need to mark your gauge to note the correction.
@johnmiller-in5bt Жыл бұрын
LOL....
@coolguybrar5 жыл бұрын
Which one is more accurate?
@connoisseurofcannabiscarsp37555 жыл бұрын
Im all about Mechanical Gauges..ANALOG FOR LIFE!!!
@uhfnutbar16 жыл бұрын
That`s good presser for AMC oil pump :)
@NobleONE172 жыл бұрын
On my DSM the oil pressure sensor is at the oil pump so I see the pressure on DSMlink and its pretty accurate..m
@heresjohnny8886 жыл бұрын
I am running almost the same set-up, a stock 390 AMC with a mechanical Autometer oil pressure and I am getting the same results. I believe it was always better to run a mechanical gauge instead of an electrical for critical readings ie:oil pressure or trans. temperature. Some gauges are just inaccurate...you get what you pay for. Example... my (Summit) fuel gauge (mechanical) read 12 lbs. when in fact the true reading was 6 lbs. It was a little unnerving .!
@kaleb16692 жыл бұрын
390 amc amx?
@flinch6222 жыл бұрын
Electric is good... but you have to come back with a nechanical every couple years and check for calibration drift as components age. Your basic bourdon tube [mechanical] is brilliant except if overpressured/off scale - then its trash: they never come back to being trustworthy. That's where electrical has it beat. When I run a mechanical gauge, I pick a range that lands [normal pressure] operation in roughly the middle third of scale - I want to avoid anything that would live in top or bottom 20% of range.
@A70AMX5 ай бұрын
@@kaleb1669 68, 69 and 70
@uhfnutbar16 жыл бұрын
do you have the oil line mod added under the intake in the lifter valley ... to the back left to feed more oil flow to the rear bearings ? i think Roger Penske Trans AM team came up with that :)
@Oldsmob4556 жыл бұрын
It's in there
@oby-16072 жыл бұрын
Why did you use gauges with different sweeps. Mechanical was 270 and the electric was looking like only 90. Didn't seem like an accurate setup to me. Did like the fast spool up of the electric over the mechanical. Biggest thing I don't like about the mechanical is the tubing required. Never use the plastic/nylon and the copper will work harden over time. Steel is ok if supported.
@Rideordie10016 жыл бұрын
Has no one noticed they are actually the same pressures? Think about it and do the math peeps.
@kenburns79384 жыл бұрын
terry thompson, yes i also noticed they are the same pressure
@doug595959Ай бұрын
electric gauges are less accurate than mechanical because with elec you have 2 variances the gauge and the sending unit with mech. you just have the gauge variance also use a quality gauge autometer , stewart warner and never use that plastic oil line . use copper tubing and i slide a vacuum line over it before installation
@mr.dozer.74714 жыл бұрын
I'm into the mechanical gauges myself. I have a question. I'm told the mechanical oil pressure gauge and the mechanical fuel pressure gauge both made by autometer are the exact same gauge only difference is the faceplate. If this is the case why would you not run a mechanical fuel pressure gauge inside the cab of your truck obviously being Diesel and not gasoline. Can you explain to me the difference between the two gauges fuel pressure gauge and oil pressure gauge
@Oldsmob4554 жыл бұрын
Don't know, talking to Auto Meter is your best bet
@Misadventures_Of_A_Yank3 жыл бұрын
Safety is why you never do that. You can run a mechanical fuel pressure guage but you have to use an inline isolator before the firewall. You can't have any fuel going into the cabin. No one will pass that in any kind of vehicle inspection. With modern components anymore, its just easier to run an electric guage set up where you only have to deal with a couple wires in the cab and to the pressure transducer. For some reason no one cares if you have an oil leak in the car. Just fuel.
@remibriere39326 жыл бұрын
Maybe you should check the supply voltage, they must be design to run at 13.8v and you are probably at 12.6 now?
@Oldsmob4556 жыл бұрын
Worth checking
@Redhawk454casull6 жыл бұрын
I was having the same thought.
@Stolencamaro6 жыл бұрын
My plastic tube broke off 300km frm home never again