Autonics Tutorial : Digital Panel Meters MT4W Series

[@KanhaiyaLal-ch3fn]

Nice

[@hoangmanhdoan6071]

How can I connect 4-20mA input of TZ4M temperature device? I only see RTD and thermos in manual.

[@AutonicsCorp]

Please refer to the manual for how to change the internal dip switch. (Case disassembly is required.)

[@cjautopecas7775]

I need to configure the MT4W - DV - 4N as an ammeter using a Shunt resistor up to 2KA - 60MV. has a video near to this project.

[@AutonicsCorp]

please visit www.autonics.com and contact the nearest branch office. Thank you.

[@muhammadfaridaziziatmaja2956]

I want to know is it possible to connect the output of mt4w aa 40 4-20 mA to AI plc siemens? Because when i measure the output is 24Vdc

[@AutonicsCorp]

In general, the 4-20mA output of the controller can be used with most of the PLC analog input cards.

[@linlianxiang4997]

can the meter show the reading of different line if 1 panel meter connect to different line? For example, Line 1 (L1) show 10V, then press some button, the L2 show 15V? If can, what is the step to display different reading or how the setting look like?

[@AutonicsCorp]

please visit www.autonics.com and contact the nearest branch office. Thank you.

[@afa8411]

Can I Mesasured the Ac frequency using MT4W-AV ? and how to Setting High/Low Limit Values for Preset?

[@AutonicsCorp]

① Set input specification [In-t] of parameter 1 group as frequency [FrEq]. AC frequency can be measured. (0.1 to 9999Hz) ② First, set the output operation mode [oUt.t] of parameter 2 group to the upper/lower limit alarm [LH.St]. After that, you can set the alarm value in parameter 0 group. Upper limit alarm value (H.SEt), Lower limit alarm value (L.SEt) Please refer to the following video link for this information. kzbin.info/www/bejne/bJTFZKpvZtiaj5I

[@monstrousamigo]

Can it be attached to DIN Rail, if yes how? didn't found it in manuals

[@AutonicsCorp]

Sorry, please note that MT series is not designed to attach on a DIN rail. This is a panel-mounted prodcut. Please visit our website for more details. Thank you. www.autonics.com/main

[@richardlofrandado6997]

How to set pressure for constant pressure booster pump. Thanks

[@AutonicsCorp]

Sorry... Is the product capable of Analog output? If it is an Analog output product, please check whether it is 4-20mA or 0-10V. Also, it is necessary to check what the maximum pressure range is.

[@randomvidtube1978]

I use mt4w-DA-4n I only can found 5 menus in PA2 Pey-t Dis-t EEro EuIn Loc Why?

[@AutonicsCorp]

This is normal because you purchased a Indicator model[N]. Certain parameters are displayed only when you purchase a preset output type product.

[@nobidiansyah4286]

I need calibrasition to mt4w- aa-40 please

[@AutonicsCorp]

First, it is necessary to check whether the scale value is set normally. (In-r, H-SC, L-SC) Next, if a deviation occurs, additional correction can be made with the Inb.L function of parameter 2 group. (-99 to 99 can be set, Factorial Setting : 00)

[@muruganalliyur5236]

Can i use speed measurement .we need 0-120v to 0-2000rpm .if possible means please share the setting configuration video

[@AutonicsCorp]

Please refer to the following video. kzbin.info/www/bejne/eYqpfY2nmpyXnbM

[@muruganalliyur5236]

Thank you

[@danialaussyukri2936]

What is hold function ?

[@AutonicsCorp]

The hold function holds the current display value through digital input.

[@user-vj6my4ke7r]

Ada video tutorial volt meter MT4W-DV-4

[@AutonicsCorp]

There are many videos related to the MT series on our channel, so please refer to them. kzbin.info/www/bejne/gpPFaXZpjLKAgM0

[@galihsaputra4780]

Power supply 12-24 v ?

[@AutonicsCorp]

Depends on the model. For example, for MT4W-DV-1□ and MT4W-DA-1□, the power supply voltage is 12-24VDC. □ is an optional output specification. www.autonics.com

[@ehabahmed615]

how can i adjust the device to range 4:20 ma for level of tanj

[@AutonicsCorp]

please visit www.autonics.com and contact the nearest branch office. Thank you.

[@BinduNodi]

Lost In-r parameter, how to set 500v,50v,10v etc?

[@AutonicsCorp]

Please refer to 01:17 When [IN-R] flashes, press the [▲] or [▼] key. And when setting, press the [MODE] key. This video will also be helpful. kzbin.info/www/bejne/eYqpfY2nmpyXnbM

[@BinduNodi]

PA-1 First parameter show Euln,disp,in-t But not show In-r parameter. How to find In-r parameter.

[@AutonicsCorp]

@@BinduNodi [EvIn] is in parameter group 2. Please review the parameter initialization. kzbin.info/www/bejne/m3fUoYOwpth9ZpY

[@BinduNodi]

@@AutonicsCorp @Autonics Corporation yes,elvn is parameter group 2. But.is show parameter group 1 & 2 both group. Now show PA-1 Elvn,disp,in-t, Group 2, Pkt.t,Euln,loc ,but group 1 parameter, in-r not show..

[@AutonicsCorp]

@Bihongo It seems that the product is not working properly. Please replace it with a new product.

[@esenco3673]

how to setup Amp meter?

[@AutonicsCorp]

To set up as Amp meter, please use model MT4W-AA-__ (AC current) models and follow the instructions (2. Measurement Input Connection) as shown in the video.For more information, please visit www.autonics.com and contact the nearest branch office.

[@azeemnaeem7165]

Autonics Corporation can u plez upload the video regarding DC ammeter. Thanks

[@indrajayadi6173]

help me,,KN-2000W series solustion connect to transmitter 4-20ma

[@AutonicsCorp]

Thanks for your reply. Connect transmitter [ + ] to terminal 5 and Connect transmitter [ - ] to terminal 1. And you should make a connection terminal 2 with terminal 4 to make loop connection.

[@KETANSHAH-u5v]

IS THIS METER USED TO DISPLAY MOTOR AMPS?

[@AutonicsCorp]

Yes, it is available.

[@vitragshah2203]

@@AutonicsCorp Can you send the full model code for the same Operation- To display motor amps. Previously in use was MS4W-DV-4N. Which is the current model sir in equivalent of this?

[@AutonicsCorp]

@@vitragshah2203 It depends on the source you are measuring. MT4W-AA-4N for alternating current(AC), MT4W-DA-4N for direct current(DC).

[@vitragshah2203]

@@AutonicsCorp What is the diff between model MT4W-DV-4N and MT4W-AV-4N?

[@AutonicsCorp]

@@vitragshah2203 I have edited the answer above. Note please.

[@ctho8814]

Lost power and now display doesn't show speed, only zeros.

[@AutonicsCorp]

Please refer to the following link to factory reset the product. kzbin.info/www/bejne/m3fUoYOwpth9ZpY

[@fernandointerior]

Can I use a load cell 4 wire?

[@AutonicsCorp]

Hello. If the load cell is a 4-wire type, it is divided into 2 power lines and 2 analog signal output lines. Power is supplied separately and two signal output lines are connected to MT4W. If you tell us the exact model name, we will be able to give you a more accurate answer. Thank you.

[@fernandointerior]

@@AutonicsCorp there aren't a exactly model, but, what I know, is that the model is a 4 wire type and 2mv/V

[@fernandointerior]

@@AutonicsCorp please... Help me... How can I do it? Where do I put the wire? How can I use a separately supply power?

[@AutonicsCorp]

[Power is supplied separately] means that a separate power supply product is required. Wiring may vary depending on sensor output specifications, so information is required.

[@fernandointerior]

@@AutonicsCorp the color is: black and blue are power, and white and yellow are signal... The power supply is a normal 10v?

[@nguyenhoainam2349]

help me. I want connect 48vdc and display 48vdc

[@AutonicsCorp]

please visit www.autonics.com and contact the nearest branch office. Thank you.

[@inplc2934]

you can scale device brother,because mt4w same with multimeter but can you scale

[@MushtaqEssazai]

Can I use it as remote digital temperature indicator? How to scale it to measure a 4-20mA current in Centigrade?

[@AutonicsCorp]

please visit www.autonics.com and contact the nearest branch office. Thank you.