MAZDA NOT STARTING OR RUNNING GOOD AFTER CRANKSHAFT POSITION SENSOR REPLACEMENT

[@AutoRepairGuys]

Products that we use and recommend: ► Timing Tool Pins ( Check for your model): amzn.to/2Bgq7Me ► Purple Timing Tool Pin: amzn.to/3U1IjC7 ► Panel Removal Set: amzn.to/3YiMADu ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Castrol Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ► Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics

[@brandonwebb2100]

How can you check to make sure the adjustments are good after you install it

[@Thabzalzk]

Hi I am struggling to fit a loose wire on the plug that connects to crankshaft sensor. Can u help me please.

[@ajf4693]

I watched a different video installing it but didn’t show to time it. It’s no wonder I still have rpms surge. Had to buy this tool, thank you guys keep rocking🔥

[@steveoneil8814]

Good video to let you know what your in for. Not too difficult but things are more difficult when the engine is in the car. You cant easily see the teeth when the engine is on the car. I rotated the crank until i saw the gap. counted back 10 and made a mark. Turned again and counted 10 of the mark for 20. You can then see the mark when you align over the sensor.

[@tpax3p]

what is the best way to change it on the car? from the top where is the battery, wheel arche or ?? Cheers

[@LarryJohnson-e9g]

Hey guys love your channel it's helped me a lot .the question I have is I have a 2007 Mazda 5 2.3L the harmonic balancer has the larger teeth on it .if I line it up with a tooth it will be the 11th tooth or do I put it between 10 &11 thanks

[@SwichMad]

This helped me replace the Crankshaft sensor after a stall on the motorway. Unfortunately now the car only starts when cold (after a day), runs smooth for a few minutes then throws P0340 ( camshaft sensor fault ). Replaced sensor ( same symptom) . Checked cabling, voltages, etc, all seems fine. On the same voltage rail I have the O2 sensor and MAF, I`m running out of patience with this vehicle.

[@GRODRIGUEZ215]

Did you ever find out the issue? This is whats happening with mine now

[@SwichMad]

Have replaced timing, no joy, I have square wave at 0.6v from Camshaft sensor, square wave at 5v from Crankshaft sensor, yet the car would not start and throw the code. Tested the sensor on the bench and supplied with 12v it outputs 0.6v when away from metal and 0 when close - so it's not the sensor. Time to dig deeper

[@lincolnmech]

Make sure the sensor is aligned.. make sure engine is at top dead center during installation.. do a crank re learn procedure

[@iryont8371]

I hope this video will help me to start my Mazda GH 2.5. crankshaft sensor was changed but car still doesn't work. There's any faults and didn't even check engine light on

[@clintdillman2950]

Awesome explanation, love the detail. I applaud you and your videos. Thanks a million

[@charlescampbell2320]

very good guys i'm buying one tomorrow and they say may have timing chain issue however it has 300 thousand miles on it must be hwy miles so may be back for more info

[@AltruisticWarrior]

Wouldn't hurt to go ahead and replace the timing chain with that amount of miles tbh. These engines are nearly bulletproof otherwise. I've seen quite a few exceed 600k miles!

[@rono3045]

if you were the one putting on that harmonic balancer and the new timing chain and you did it that way you might be wrong because top dead center could have been on an exhaust stroke..you need to look at the position of the cams also to make sure it's a compression stroke top dead center not an exhaust stroke

[@JD-ml7cg]

No need to do that.. The crankshaft pulley has a alignment hole. The hole should be in the 6 o'clock position as in the video. There is nothing about 20th tooth. Cps should be on the nearest tooth. Done deal

[@Monsterenergyoffroad]

So can you adjust the cps by using a bolt to keep the harmonic balancer in that position?

[@MartinX192]

The cam should be turning 1/2 speed of the crank. You could be 180 degrees out on the cam or as he said "exhaust stroke" unless of course this engine is 1 to 1 rotation crank to cam somehow@@JD-ml7cg

[@ninevoltmodz4687]

I didn’t even use the alignment tool, if you go over 20 teeth to the left from the gap, and line up the 20th tooth on center with the sensor, it will be fine. The car runs really smooth, you can balance rocks on top of it.

[@originalhondaddy4206]

I’ve been looking for this exact video for ages now I know

[@raulbatista4779]

very good video. I make a query. I have a Mazda Speedy 2009 2.3 L. I have to change the steering pump, but I can't find it. do you know if the pump of the cx-7 2009 is compatible or the one of the Mazda 6 2.3L.

[@oscarespinosa5384]

I have a question, you said in another video that you have to count 22 spaces to have the time for the cranshaft sensor, now you say 20, could you tell me he much spaces are to fin this sensor?

[@sacredrodriguez850]

Hello I have 2005 mazda 6i 2.3 did a engine swap with a 02-05 jdm 2.3 motor. I had to swap timing cover, crank pulley, CKS sensor, valve cover, water pump pulley, intake manifold, exhaust manifold and throttle body. Now car cranks with slight start but cuts off immediately. I need advice on what I'm doing wrong?

[@richardriri464]

Can you help me? I've put a L3G motor from a 2002 Mazda Atenza Sport into a 2005 Mazda Atenza Sport 6 speed. I've changed everything from the 2005 motor over to the 2002 motor. The motor turns over then flattens battery. Dash fades when turn lights on.whatni. I've been told I need to change the crank shaft. Should I just do the timing like in your video or do I need to change the crank shaft and do the timing. Do you have a link so I can see where every thing on the loom goes to the motor. 1. DO I NEED ANOTHER CRANK SHAFT. 2. DO THE TIMING. 3. CAN YOU RECOMMEND A LINK I CAN USE FOR WHERE EVERYTHING ON THE LOOM GOES ON THE MOTOR. THANKS

[@sacredrodriguez850]

Hello I have a 2006 mazda speed 6 with blown engine and a 2006 mazda 6i 2.3 with a good engine. Can I put the engine from my 6i in my speed 6?

[@Worthyhighlights]

Would this be the cause of why my mazda miata is not starting after buying it from the auction, with a damaged front end?

[@steventrujillo2703]

Hay I watch all your videos on Mazdas however; I have a mazdaspeed3 2009 I took it to the dealership and they told me My mazdaspeed3 has check engine code p011 p0016 and p0301 as well as oil in my spark plugs do you think the engines work is worth fixing or should I purchase a new engine?

[@Pw-f100]

Probably a valve cover seal around the spark plug

[@perryj20]

Thanks for the video. I have this same engine you are working on in my 2008 Mazdaspeed 3. The car will start up; run great for one second then immediately die. If you try it again it will do the same; start then die. The engine check light is not on and there are no fault codes. Anyone have any ideas?

[@armanmaaba600]

Hello how is that timing tool pin. I can't find one here so i want to fabricate with same length spec?

[@danielwheeler175]

So will i need to do this if I’ve removed the harmonic balancer

[@dakkadakka9189]

Yes

[@marklewallen9129]

Is it not possible to do it by leaving the bolt in....? Does it not serve the same purpose

[@michaelhatfield7647]

I just changed serpentine belt on Mazda 5 2012 and it’s running rough on de-acceleration. I turned crackshaft pully to walk belt on and now those symptoms. Could it be timing from me turning crankshaft or separate issue?

[@dachande1797]

Hi mate i recently have replaced belts on my mazda 3 and im having the same issue. Did you end up finding ouf how to fix it? Thanks

[@michaelhatfield7647]

⁠I can’t remember but I had it going shortly after writing this. I think it was that magnetic thing you see in video needed in the right teeth. I put my ratchet on and turned it a tiny bit I think and I it tried to fire and I went some more and it’s been good ever since. I’m know mechanic or anything and that’s what worked for me.

[@frankluisroperto1793]

Cuanta pulgada tiene el tornillo q sujeta el sigueñal del motor 2.3 mazda cx7 año 2007

[@zayn8810]

How many length . The pin timing bolt ?

[@steezystev1717]

Is this the same for the sky active? Mazda 3

[@jessherc1]

Thanks, does did work for 2003 Mazda protege 5?

[@joogmanhd4878]

Hey I have a question there is also a cable that hooks to the sensor if I am replacing mine, do I need that cable also or do I just need the sensor

[@Menace_sti]

Do know where the gap for the crankshaft should be facing when at TDC

[@zuttoish]

not only tdc, you need it on compression stroke also

[@christianmendoza5799]

And how do you do that?

[@studdmuffnn]

Mazda service manual only ask for TDC for this.

[@zuttoish]

Rohan Ellis every mazda guide clearly State tdc cylinder 1 on compression stroke. Not sure where you found otherwise.

[@christianw.8129]

@@zuttoish It doesnt matter. The crank sensor tells the pcm when the piston is at tdc. The crank will have the same position either its on compression or exhaus stroke. The camshaft position sensor tells the computer the cam position (which defines the stroke via the valves).

[@bongiovi666666]

Hey guys. I need help. Do you know the torque of crankshaft holding bolts? I cant find anything on the Internet.

[@elijahwoodz6954]

What if it’s for a 2.3 crank shaft pulley but doesn’t have as many teeth as that one

[@zacharyfisher4383]

My Rx8 wouldn't start, OBD2 showed a code for eccentric shaft sensor, so I bought a new one, replaced and I don't remember the original code, but the code changed from the first one to eshaft sensor improper range function? My eshaft sensor is different from your crank sensor, mine isn't adjustable, did I do something wrong? When I put original back on the car, everything started working again...? Still works, but would still like to know what I did wrong

[@noekumagay7114]

My nc 2006 Miata does not have 20 teeth after the space. What should I count?

[@jeanzongo3631]

Do you know where I could find the timing bolt for Ford Explorer 2013 2.0L 4cyl ecoboost ?

[@nev7490]

Hello guys my Mazda cx7 2010 Runs and starts perfect but once of a sudden it shutdown and the rpm go lower until it stal and shutdown while running over a bump or if I just slow down

[@goncalvesalexandre5441]

Hello everybody and SOS please 😰😰😰😰😰😰 I don't understand at 2'20 what is said. What should we do with cylinder #1 ? Many thanks for the information and THANKS a lot for this video 😀

[@rojegallarde5835]

Thank you so much men GOOD JOB

[@skullmps]

Can be a reason for misfire !? Thank you mate great video

[@AltruisticWarrior]

Absolutely can. So can the camshaft position sensor. More likely than not though it's just the coil packs. They're prone to going bad on these because of the way they're designed. Can get 4 brand new Bosch ones from Rockauto for roughly 90 bucks. They have a lifetime warranty as well! They're far more reliable than the ones you can get at autozone or oriellys. Those never last me more than a year or so and even then I've had some have small hardly detectable misfires brand new. Made for BAD gas mileage though. I was down to nearly 10mpg

[@getthegearnow-store2451]

On mine if i have the pulley lined up with the hole in the cover, the ninth tooth lines up. Not the 20th. I have 2 pulleys/balancers. They both line up with ninth tooth.

[@2sumu]

6:03 I don't know why I watched it but I did.

[@brice5001]

What is the name of that 10mm purple bolt?

[@nathangionet2088]

If we remove the bolt is there oil that will come out? Just making sure cause i need to do mine

[@irisroman8331]

No

[@mehtabahmedabbasi8466]

Mazda 6xseater 1992 Pick up starting problem vedio kindly share

[@dvdrmrz15]

Are the specs the same for 1996 mazda mpv 2wd

[@oneilbrissett4854]

All the way from Jamaica gays, love your vedio's. The problem I am having with my mazda5 2014 Mzr 2.0 from Japan, when I start hear rattling sounds coming from the area of harmonic balancer mostly cold start or when ac circle off. Help please.

[@dakkadakka9189]

I would check timing chain, how many miles on it ?

[@noekumagay7114]

My does not have 20 teeth

[@mx6146]

Would that make your car run on 1 cylinder?

[@Luchone]

the cx9 is same engine on Mazda 6 3.7L ?

[@Runescapian1996]

No

[@bintapapacamara]

Thank you very much

[@eivervelez5890]

Mi mazda protehe5 02. Los coil no avientan chispa saben que sera?????

[@f128kh4]

Thank you Simple and helpfull

[@ryandungy151]

Very helpful bro, I have a similar engine, Mazda Atenza and after rebuilding it I was able to rotate the cranckshaft but after mounting on the torque converter along with the transaxle I could not rotate the crankshaft anymore, do you have any idea bro on what could be the problem? Thank you.

[@dakkadakka9189]

Is it in gear ? Problem with flexplate or torque converter ?

[@gabeo9474]

If your torque converter doesn't get seated all the way into the trans, then it will contact the flywheel and get pinched when the engine and trans are bolted together. I'm guessing this was the problem for anyone else that has this issue.

[@fingerz6983]

@@gabeo9474 hi there did you notice you’ve answered the question 50 weeks later ? Do you think this was wise ?

[@gabeo9474]

@@fingerz6983 Have you ever considered that someone else might have this same problem in the future? And what exactly compelled you to read these comments and reply like an ignorant jackass for no apparent reason?

[@anelisangqukuvana1866]

Which place that i can get this boltt

[@thomasholmes536]

I tried this on a Mazda Millena 2002.

[@Khaled-if4xs]

Nice teaching

[@armandoollos8828]

I watched ur video. So I was inspired to buy a mazda3 2010 for $300. Nice little car. It was smoking white when turned on. Figured previous owner over heated it and head gaskets when out. I have watched ur video called step by step and when I put everything back together I turned on the car. Never started again. I took out the spark plugs and they where smashed in 1st and second cylinder only. 3rd and 4th were ok. I have gotten really good at taking off the cylinder head and timing components In less that 40min lol not bad for a person that's never worked on a mazda before. Anyone reading this? Has any idea as to what my issue is. Please let me know. Thank you.

[@armandoollos8828]

Ar this point I think it'll be cheaper dropping an used engine.

[@armandoollos8828]

I am shure it's a timing issue but I have done everything step by step and it doesn't turn on. Before it did it just smoke white when turn on.

[@randyloveday9220]

It is an interference engine. While the spark plug itself can't make contact with the piston, the valves will, if the camshafts aren't held in position. There is a tool to hold them in time. One or even both valves can get bent and broken off inside the combustion chamber. If the valve then gets caught between piston and spark plug area, you will then have smashed plug.

[@johnnyaceadams7694]

Ever get it started? Mazdas are fussy misfits. Fuses, relays, wiring seem to not do well, especially with summer heat. Could be any of these...:/

[@victoriakamati7882]

I have a Mazda astina 323 1996 model but can't find crank sensor plse help

[@hasankhaalis9039]

Were for crankshaft bank 2 bank and 2 for ford ford 2006 500

[@ccautollc864]

I would think this could give a p0016 code as well correct?

[@ZhTuR]

Perfect! Thanks for sharing!

[@richarftreloar2006]

Hey boys thanks helped me out heaps keep up the good work an

[@DonaldWilliams-n7o]

Where is the crankshaft position sensor for a 2015 for edge sel 3.5

[@1963Macky]

Very helpful thanks

[@rjb6327]

Nice. Now show us how to get to it.

[@caseygray2958]

Thanks very helpful

[@ryandungy151]

Thanks man, very helful.

[@joeishere500]

Wow man . Crazy stuff

[@FizeMooradan]

Hi guys my mazda 2001 is it the timming

[@waymaker1411]

Thank ypu for the tips

[@noahbannister1834]

Ok, thank you 🙏 ok

[@eduardoramos2281]

Cool I like it this tools

[@spelunkerd]

I wonder why they chose such a complicated procedure.

[@juanpaz6707]

Because Ford that’s why. I’m glad Mazda went away from all the Ford bs.

[@ninevoltmodz4687]

It’s really easy actually, it took me 5 minutes and I didn’t even use the alignment pin.

[@emmanuelbanda1147]

Thanks

[@nicolasrodriguez6247]

Pin 20 or 22 ?

[@DanitoConstane]

😢😮🎉Which sensor drives kilometers to the board

[@chaoticfox6271]

Does this work for code u0100 p0340

[@AbuOmar1970h]

if r.p.m not move when you start car = crankshaft sensor is damage . result the engine not work .

[@benedictmagano7948]

Show me AT

[@SirSodaPoppy]

Okay.. okay.. 🆗️

[@stimaquinarias]

arroja codigo P0012 ?

[@roberttemple9899]

My mazda 3 will not start gave someone a jump a min later car will not start only clicking and security light on now

[@DRT-81]

Cant you just paint mark it ?

[@nct9466]

Yes and TDC is the small hole in crank pulley to thread in front cover. That’s enough to set TDC when you’ve not undone crank pully

[@tuckergomez6740]

Why tooth #20

[@johnnyaceadams7694]

Same question...:/!

[@petervanhaeften]

🎉

[@benedictmagano7948]

Start the car promblem not display gear show me AT

[@NjabuloDube-o7f]

My mazda 5 just shart down when I accelerate

[@shekharviswkhrma4201]

👍👍

[@erniepcabral5905]

No comment.

[@joshualawer8943]

Divine Labista

[@AqilGameMasters]

Cant andarstend bro you not xplen purfet

[@richardcunningham7964]

Awsome good to know. These mazdas are the worst car ever made . Engine wise. Theres no room to do annything un der the bonnet . Knightmare car. GreAt work

[@thecritic8318]

I highly disagree I got my 2.3 na to 285k drove 3hrs no oil still got me home. Been addicted to mazda every since. Currently own 2 mazdaspeed 6 and a 2010 mazda 3 2.5 na.

[@check8outbro]

rx8

[@patrickkabefe1475]

00

[@MiguelTorres-fc6vb]

THIS is not correct . He is totaly wrong .WHAT happens if YOU DON'T have THE tool . HOW can YOU do that with THE axle on . YOU sre not HELPING anybody. People the new sensor comes with THE correct position and yo will remove THAT piece after YOU install the sensor The engine pulley has a timing precision on the bottom of THE pulley. The VIDEO shows a engine outside not on the vehicle. GOOD luck

[@cedrictarkelly5438]

Thanks