How to connect LED STRIP to speaker(BASS)

[@ANTIQUE_FARMING_EQUIPMENT]

HEY EVERYONE DON'T TRY THIS CUZ IT CAN BLOW YOUR AMPLIFIER OR HOME THEATER JUST TAKE A 1K CAPACITOR AND CONNECT IT TO LED STRIP+ THEN CONNECT - WIRE TO LED STRIP AND ANOTHER WIRE (+) TO THE OTHER SIDE OF THE CAPACITOR THEN CONNECT IT TO YOUR SUB WOOFER OR SPEAKER 👍

[@ESydeGaming]

He connected it to his stereo system

[@RidinChevySolo]

LEDs require a 12v DC source. Your amplifier emits an alternating current or ac. This will effect how the load on the amp is received, and will cause damage to the components. Please stop telling people to do this.

[@tuffgong3248]

Is there a way to do it

[@tristian6865]

1. Ruins your amp because of impedance 2. Only works with highs, unless you have a really powerful amp

[@CARMEKANIK]

please dont inform people to do this as it will burn up the amplifier...

[@jblchange3channelandsounds284]

lol?

[@marcel7036]

Yeah, TexasXplorer youre right

[@paczkos545]

it did not burn the amplifier

[@timnerenberg]

@@paczkos545 not immediately but it will

[@moocrafter972]

Why? Pls show me i dont understand

[@entertainmentstation4662]

1: you make it look like more difficult 2: frome amplifier you get less power when it's normal volume, so you have turn volume a lot higher to get enough illumination * putting led directly not gonna helps you * just simply buy two amplifier one for speaker one for led There can be other alternative but At least you don't have to turn higher volume and 100% sure that your amplifier don't blow ✌

[@tharindugihan6383]

This is very good to the amplifier 💥💥💥💥rest in peace

[@locorimax]

right

[@pragavirtual]

well im not very knowledge in eletronics but i know some, so there is a way to kill your amp by doing this, using AC (speaker works with Alternate Current, leds are designed to work with DC) with leds, youre forcing voltage into led in a way they are not meant to have, doing that any led in the strip may fail and go into short circuit and then kill your amplifier. Im thinking that theres is some workaround to this, adding some other diodes into the negatives and RGB inputs on the strip, or just using some resistors in the same way to limit the voltage that goes to the leds, dont ask me for schematics bcuz i dont know.

[@robertopascasio8570]

Hello Sir, how many led bulbs do i need for this particular project, thank you in advance.

[@harddrive7316]

The title should be: How to blow up your amplifier

[@alexandruargint1937]

Yap :))

[@vee9260]

How....

[@RiccardoRivi]

@@mathwins7953 so if i have a 1973 Pioneer amplifier does it work?

[@isaacsanchez7317]

Why?? Could you please explain me?

[@immensiverocker4813]

Exactly because I tried it and I blowed my amplifier too... Please don't try this

[@badshah3002]

Buy Yeelight Strip light this feature is also available in that strip

[@SantoshG360]

Please give links

[@georgiodavid]

Can I connect it to every 7.1 channel? So I have separately visible from every sound channel

[@perrypebriant506]

Nice I get inspired

[@OpsterGamingYoutube]

This is like the kind of thing that i would love to do but i just know that i will never bother learning because of the danger of fire lol. I wouldn't trust myself to not mess it up xd

[@ConstabeastYT]

I am 12 but....same 🤣

[@CH-FOUR]

@@ConstabeastYT i am 13 and i do this things for 5 years now

[@CH-FOUR]

@Teodor Vranchev i like mostly computers and speakers

[@why_ju_st_why]

@@CH-FOUR same

[@Ryanwheatley07]

Yall, i only recommend if you take abart old bt speakers and use em for diy bs systems, I use leds with it straith connected, but if you have an expencive system that you def dont wanna replace, dont do it by anymeans, i actk as a short circut and will blow the sound chip real quick

[@scottneulist9495]

Nice, do you know if this works with more powerful amplifiers/speakers. Thinking of hooking them up to my 600w RMS subwoofer in my car

[@leeknivek]

Bigger resistor, you only need a tiny amount of power from the signal and 600w will blow these up. (I think) if you have an amp that does 600w @ 8Ω then it will do 300w @ 16Ω, 150w @ 32Ω, ...... 16w @ 128Ω, 8w @ 256Ω - measure the resistance of your strip and make up the difference in impedance with another resistor inline to bring it up to the correct value. I would check the rating of your amp first, if it is actually 600w at 8Ω or 4Ω or whatever, from there you can extrapolate where you need to get to.

[@Cashendogs]

@@leeknivek it will work I’ve done it to amps that push out 1800 watts 🤙🏽

[@parshuramjadhav2467]

Loved this video because no difficult tasks is there...

[@mantasbudrys9941]

It will burn your amplifier and btw there is Sony speakers with pre installed LED

[@VlogswithVikrant]

Bhai kisi bhi hometheatre se kr sktee hai kyaa

[@Retro719]

Remember the Radio Shack light organ boxes, where each of the 3 colors operated on the different sound levels? That's what I want to learn how to properly make.

[@momory1999]

hey, i just find your channel in my recommendation and we have almost the same "name", i tough it was funny ^^! nice content by the way

[@AVmake]

Hahaha that is funny, thanks!

[@KHKIEGAMINGSHREE]

kzbin.info/www/bejne/oHKlemOrgNmjgac

[@johnnymotors2023]

Braw.... this shit I was doing when I was 12-14 years old... now I am 24.... I thought that u found something better not like this. Something that will light up even you have the volume at 5% or at 50% and will illuminate with the same intensity based on the bass kicks, etc.

[@ladyboss4842]

How?

[@Kanoshe]

yeah apparetnly you gotta have like arduino's and coding to make it proper

[@rafee9442]

​@@Kanoshe you can use a spectrum analyzer board

[@projectmanagement2356]

Somebody got his big boy pants on all by himself 😂

[@JAMBI..]

Yo I've been searching for shit like that. Every tutorial or led light kit seems so basic.

[@Adexi1]

This is so cool !!! Amazing :D

[@unboxingedicas223]

Nice work!👌👌👌

[@shadowdrimex5226]

Hi Hifi, it was the same and the ohm is adjusted to the speaker, performance when recording and transmitting, it's no use putting up a series of LEDs equipped with resistors, an LED works at about 3v, so you not only damage the hifi, but it can also cause a short circuit because there is no switch on it!

[@koningvanongewonekakies7419]

Can you blow the LEDs with too much or would they not blow up??

[@tadyslo1203]

They wont blow up but they will die

[@conxtantino]

It was perfect, congratulations

[@atsstockburn]

I've never seen so many "no-no's" in a how to video. I won't even go into it. Everyone has to learn somewhere. lol.

[@Thesaint2k13]

Nice job , pretty sure the amp can deal with the extra 12v power draw , lol people in comments make me laugh it's not like he's going to have it on 24/7 with speakers at 100% lol it will be fine worst case scenario you have a power surge and pop an led , lol

[@twowheeldrivetwd885]

This kills the amplifier

[@gameboy1984]

How?

[@davidluptak]

@@gameboy1984 Drains too much current from it to light up leds

[@Kanoshe]

@@davidluptak go on

[@davidluptak]

@@Kanoshe Amplifier is for speakers with definitive ohms and if you add another appliance like leds than mosfets or chip may burn up from excess current

[@Tesdraline]

@@davidluptak 4 ohm speaker is a much bigger load than those few LEDs

[@cirilogomes7477]

congratulations, you work is very beautiful. parabens, seu trabalhor ficou muito bonito.

[@randomvideosfromtiktok5583]

3:59 music title please?

[@madhukeshnp]

Use a transistor to switch the led strip and connect the base pin of the transistor to the amp like you did not...

[@sergeeveraers]

One tip you meed to use a 5v (volt) led strip with a collor blu Red or green use to much voltage I hope this wil help you with making these things👍

[@stefan0058]

Nice Video

[@TheLordAdder9]

Is the led light connected to the bass or is it separate? Is it safe to cut the led cord or will the bass be cut too?

[@script2351]

Evet bass'a bağlı

[@Diablo-RED]

hi brother what is the positive lead the green? .... the green goes connected with the red of the amplifier?

[@TorbTorb]

10 m led strip have about 24watts so his thing will have 3 watts. so shouldn't impact the performance a lot.

[@ismaelmeza1800]

Eso no afecta el amplificado o puede dañarlo por la carga de tira led

[@gustavopetitpanda]

para mi si

[@nashtech8548]

Excellent Work ..

[@Speakershocker]

You kill the amplifier!!!

[@marcel7036]

Ja Moin, dich sieht ja man überall😂

[@Speakershocker]

@@marcel7036 Ja normal. Sowas wie hier geht auch nicht. XD

[@marcel7036]

@@Speakershocker ja geht auch nicht, teure Verstärker schalten da schon automatisch ab

[@Speakershocker]

@@marcel7036 bei so einem Unfug aber auch nicht immer.

[@leandroebner1405]

@@Speakershocker kannst du mir erklären warum hier der Verstärker kaputt geht? Kenne mich jetzt nicht wirklich aus aber wer nicht fragt bleibt dumm... Wenn jetzt theoretisch die Gesamtimpedanz über der Minimalimpedanz des Verstärkers liegt (z.B nur die LEDs ohne Boxen) fährt der Verstärker doch auch nicht ins Clipping. Dem is dass doch egal oder? Oder weil der Strom jeweils immer nur ne halbe Periodendauer fließt weil die LEDs während der negativen Amplitude sperren? Was schädigt hier dem Verstärker? Danke

[@atifprince4355]

It's led 12V bro?? Kindly reply

[@pa-novus]

Oh Junge 🤦‍♂️ macht das bitte nicht nach, das zieht eurem Verstärker nur Leistung und senkt den Widerstand des Lautsprechers am verstärker was ihn zerstören kann.

[@SPEED4DAVID]

Das Stimmt Nur bedingt! Dem Verstärker ist das erstmal egal die LEDs mit widerstand haben einen VIEL höheren widerstand (je nach länge) als das sie schaden anrichten könnten. ABER Ein Problem ist eher das der Verstärker ungleich belastet wird. LED Lassen Strom nur in eine Richtung Durch Das heist die belasten auch nur bei einen positiven Impuls NICHT aber bei dem negativen. Dafür wäre eine Gleichrichtung mit elko nötig) Das ist aber MEISTENS auch nicht das Rissen Problem der Hacken an der Sache ist du must schon >SEHR LAUT< hören um auf die Spannung zu kommen das die LEDs überhaupt glimmen. Und im Video wird extra ein sehr bass lastiges Lied verwendet und das noch sehr laut damit die LEDs überhaupt flackern. Bei Zimmerlautstärke wird sich gar nix tuen oder kaum zusehen.

[@DieSpeckBohne]

Ich hab's mir schon gedacht das es nicht so einfach sein kann

[@doctorpetrovich9296]

just buy Cheap ($2.50) LED driver that controls RGB stripe according to music bass line. Connected to 12V it detects music rhythm and flashed LEDs to the music. This creates disco/club-like effect, visualizing BPM of your music.

[@gothangel6221]

are they just callef LED drivers?

[@doctorpetrovich9296]

@@gothangel6221 i think they are called Arduino Uno LED Sequential Control

[@as424100]

You know that you actually can cut the shrink tubes shorter depending on how much you need?

[@paulybeatz3688]

I knew it but I don’t do it. Cut is cut

[@as424100]

@@paulybeatz3688 I know man but honestly it drives me crazy when I see someone wasting material like that..

[@tadyslo1203]

Yes all cool and that but if u have a radio that outputs more than led's are rated for they are going to frie.

[@rogertyler3237]

I Have Some Led Strips with 4 Pin Connectors How Do I Know What Wires Are + Or -

[@Ryanwheatley07]

I don't recommend it at all, but black is usually negative, use a battery to be sure

[@Kalindu123]

Thank you

[@jaybalbuena5045]

what is that 2 small metal what is it called?

[@hashirabdulrazak5810]

Can we connect light direct speaker

[@leoye7814]

Actually u can just go buy rgb led strips with mucis mode

[@tushargupta9024]

Cost bro 🤧

[@wesoyrozkurwiacz2126]

Can I do this with my Creative A120 ???

[@aman-reverbs]

Thanx bro

[@VladyslavShchelkov]

all genius things are very easy

[@NVMUSICTV]

By doing so you are reducing the power inputed to the sub

[@jomann3213]

What? You know this is a 3 way speaker yeah? So all 3 drivers would be affected not only the woofer (or sub as you call it even tho it's not). You are mostly just burning out the amp.

[@SalComposer]

@@jomann3213 you can have a woofer with only medium and hight frequencies on it... what are you talking about? sub is a professional term to define lower frequencies under 60Hz that is even the frequency that electric current flows, besides, that kid also named the video about BASS , and no... not all frequencies are afected the same simply because the amp sends much more power from the crossover to deliver in the speacker the low and sub frequencies, than for the highs frequencies. If you use old lamps, you will see that they dont move much with the highs of music almost nothin but do a lot with kick drums and sub bass. for you to hear from a speaker tweter 15000Hz you need 300 times less energy from the amp, than the energy you need, to hear a Kick sub on theyre usual 50Hz frequencie.

[@bujanganbujang1555]

Bikin video bos pasang lampu led semua jenis , dri lampu kolong lampu led strip dll pasang ya ke batok lampu sorot viar 200L dan motor matic

[@yushirgunpath709]

Do the colors change?

[@AjayJadhav-tr8iq]

Ap na ky use kiya ha bata sktaho

[@gurmansingh4542]

Can it be done with f n d 550x

[@Adhilahamed123]

Thank you so much ❤️

[@LeeroyLeBG]

Ok i'm going to try it 😊

[@richard16372]

Is that a normal 12 volt led strip?

[@AVmake]

This is RGB(red ,green,blue)led strip 12V, so I can change colour by connecting different wires, but you can use one colour led strip that's more simple.

[@AliYassinToma]

@@AVmake but what if the sub is in the amp and only tweaters are out of it ...

[@BrokenBoygaming_pb26]

Is not working 😥 plz help

[@jatir_bhaii_]

Bro how I set in microlab speakers

[@ray1002]

I hook mine up different but good idea

[@KarthikJsuvarna]

Awesome good bro 😍

[@matseiss4714]

very usfull video i am actully gonna try this with my own speakers and subs when i get the led strip:)

[@mikaelaakervik6794]

You will blow up the amplifier if u do it. Please dont.

[@zeusslightning1238]

Don't do it!

[@lescap1209]

Is everyone here just to tell people not to do it?

[@obaidullah4044]

Bhai is led strip ma length ka bhe hesab hota ha ya nai Replay plz

[@RyanProxy995]

Bro, I need some guidance with a project that I am doing, can we get in touch?

[@barrytrowbridge5067]

How meny LED can you have of the speakers

[@linsonlazar3657]

How many led lights can it make glow? Because when i connected a series, it didn't glow. Can you help me with some calculations

[@elektromicha6777]

bro this is fake ;/

[@VC27]

@@elektromicha6777 - Seriously? Do you even know what you are talking about? I did this with a car headlamp bulb when I was 13 on Dad's old Aiwa AF-5090. Lucky that it didn't fry the amp., should have added a resistor. However, it worked! Stuff your mouth with your old socks before you call it fake.

[@digitalcorner5101]

So cool

[@bikramveersingh6027]

Where to put the wires in the input or output socket???????

[@harshitseth7239]

Can we use 20 watt led strip tube light on strip (T5 100 led)without driver please reply anyone ASAP

[@sabbirtech8847]

Nice

[@monermajhi2218]

Is amplifier ka Kya naam Haii Plzz link dija.....plzzz plzzzzz

[@vaibhavrjn]

Where did you insert the 2 pins

[@SANBOOST]

song at 4:03

[@johnlloydcabacungan5717]

Can I go directly to speaker?

[@ANTIQUE_FARMING_EQUIPMENT]

DON'T TRY THIS

[@johnlloydcabacungan5717]

Bro I know it how to work set up I know operator I know

[@ANTIQUE_FARMING_EQUIPMENT]

@@johnlloydcabacungan5717 Get a 1.1k resistor and connect directly to speaker

[@euvo_sound]

i also made this one but the amplifier never blew up.

[@Kanoshe]

@2:30 holy fuck that works good.

[@davidedgardodiazchavez9116]

Bro tengo el mismo aparato solo que de tres bocinas pero me da miedo conectarlas así nomás que posibilidades hay q no se me desconponga en equipo de sonido

[@toptohyekoms]

I think you're very cool and handsome too! coz you got the same lighter as I am

[@sharmasudds]

Please try this if you want to buy a new home theater

[@paczkos545]

Why?

[@famiivt4259]

It burns the transistor

[@official-on8qh]

led price ??

[@mariniluca9197]

Pakai adaptor gk bang

[@michelleyoung934]

Can you add led lights to JBL boombox 3

[@conxtantino]

Perfect

[@JabrikOficial1996]

is Good

[@spyboyAchin]

Vai led strip kitna volt ke hai

[@KHKIEGAMINGSHREE]

kzbin.info/www/bejne/oHKlemOrgNmjgac

[@rogertyler3237]

Hitlights Told Me The Led Strips Won't Work Just Connected To Speakers. They Said They Need A Content Steady Flow Of 12 Volts.

[@scottortizortega2272]

Me gusta pero alumbran mas en los bajos que en medios...

[@bluepen215]

Awesome

[@ronaksingh7149]

How much wattage the led strip light should be?

[@ronaksingh7149]

I have made a 200w speaker I power it up with 12v 5amp adaptor

[@ronaksingh7149]

I have tried it when I power the speaker it just bumps up and not blink after the music is on

[@ronaksingh7149]

Please let me know about it

[@yaunok]

It worked only on louder bass. Lower Volume didn't work :D

[@bersa2934]

Hola buen dia yo tengo esa luz led pero el mio tiene dos cables se hace lo mismo ?

[@edwindanielramirezlopez5490]

Si le das más volumen no se queman decasulidad

[@carmensantiago3001]

Reduzco el bajo de la fuente para que no te quedes sin poder hacer la transferencia por transistor dé poder tener una fuente extra para que no te quedes sin poder 🤔🧠 capasitor en la fuente extra

[@FireInFairy]

Unmm, I don't know about that one. The speakers run on AC voltage and LEDs work on DC so it would not work. But I think your led strips are AC voltage because you are not showing or writing it.

[@decoandrade1644]

Boa noite bacana seus ledes -? Dar para mim ligar no homer teite também nesse da LG

[@adamasyudistira180]

Song?

[@TenzinWood]

0:05 SONG NAME?