B6 VW Passat Headlight Removal

[@dennismendez7546]

You helped me change my gf light, therefore, I love you .

[@andreasw589]

Sehr gute Erklärung 👍👍👍

[@johanpieters739]

Thanks, very helpful. 😊

[@nocturnepassenger3227]

Yo, after watch your guide i can tell you its impossible if you have headlamp washer xd.

[@MeFixingEverything]

Ahhh I haven't think about that. Will put it in the description. Thanks for your comment

[@nocturnepassenger3227]

@@MeFixingEverything Maaan no problem :))

[@edbeadel]

Apparently you can. I've just asked on the R36 forum and there's a guy there said he's done it. I'm trying mine tomorrow.

[@LordGryllwotth]

Oh damn! Thanks for the info. I have seen a video for Finland, and since he had HID, I will guess he had washers.

[@JustVankata]

Бегай бе циганин

[@paulsnowsill633]

Thank you, really helpful!

[@alexiooooooooooo999]

You’re actually working more

[@rolandneumann34]

You can reach the bottom screw even with a small accu-drill. With some 60mm long nut or nut with spacer. That´s even easier than in the video. But set the driver on "full power"! It takes some time to place it correctly, and it is very nasty, if the accu-drill´s clutch slips (I know, what I´m talking about :-P )

[@petjaslavichuk7827]

Чувак молодец

[@petjaslavichuk7827]

Биксенон тоже так снимается?

[@josephnoneofyourbeeswax8517]

I am going to attempt this tomorrow at 0F. Will the plastic break? Would a swivel head ratchet wrench help?

[@MeFixingEverything]

You will be ok with the plastic. Your hend will definitely freeze 🥶. Swivel head ratchet is not needed , its not on angle, it's just a bit tight. It was a lot easier to put them in. Pay attention how I take the headlights out, they go the same way in.

[@paulgoals]

Im trying this here and its not possible to reach that bolt it faces towards me so you cant get it out

[@rolandneumann34]

There is enough space to unsrew it and take it out. The plastic "bar" some 5cm ahead of the screw is not massive, there is a big hole in it, so you can go through it with a 10mm-nut and extension (and an accu drill driver)

[@paulgoals]

@@rolandneumann34 after a very frustrating time i got it !

[@kcmustilp]

I did attempt this today but i couldnt find the screws from below. I searched for it like 30min but i cant see or feel screws The screws where you put the 10mm in and go in the foglight hole and go above to the headlights

[@MeFixingEverything]

Tough to find. If you struggle over 10min wll suggest to remove the bumper.

[@rolandneumann34]

This one goes the same direction like the other 10mm screw! Not up- or downwards.

[@technocris1]

Thank you man , you saved my time !

[@MeFixingEverything]

Thanks for your comment

[@ldarm]

I'm not sure what i've done wrong; but I removed all screws and the thing doesn't move an inch 🤦🏼‍♂️😂

[@rolandneumann34]

Not all screws probably 😲 . There are four of them. The two hidden ones are pretty long, some 45mm, I guess. Then pull the inner side of the light towards you, - might be a little rough. This ist not to be seen in the video.

[@mikem242]

To wygląda, jak porażka w wyciąganiu zderzaka, lepiej odkręcić dwie dziesiątki ze zderzaka i go uchylić z boku a nie grzebać jak ginekolog.

[@MeFixingEverything]

Don't be so sensitive

[@ukasznowaczyk8034]

"How to scratch headlights on VW Passat B6"

[@pisokissivi]

It's it impossible ?

[@MeFixingEverything]

I can't get your question ?

[@tonybrandt6605]

Mycket uppskattat .Ska testa detta sättet.

[@MeFixingEverything]

Tack

[@godskills666]

Junge nimm den Stoßfänger ab geht schneller 😂 und mit Waschanlage geht es so auch nicht

[@henkka410]

Top 10 most stupid designs of all time....

[@MatiasHeinrich1]

Very helpful! Thank you