Ba/Bf falcon gear shifter surround replacement (how to)

  Рет қаралды 54,452

Sol's Creations

Sol's Creations

Күн бұрын

How to replace bubbled shifter surround and globe in all Ba and bf 4 speed falcons.

Пікірлер: 94
@philip2777
@philip2777 6 жыл бұрын
I was able to retrieve the clips that were "lost forever" as mentioned at 9:50. Inserted some thin rubber tube into a vacuum cleaner hose and taped it up, then turn on the vacuum cleaner and fished around for a couple of minutes, and was able to pull them back up. Also, when removing the PNRD shifter surround, you don't have to force it. Use needle nose pliers to squeeze the bottom of those serrated tubes... there's a split in the bottom of them. Awesome video... wish I saw it before doing this job!
@hugme0rdiejf
@hugme0rdiejf 6 жыл бұрын
Thanks for taking the time to do this video. It was all I could find on the internet to show how to get to the auto selector cable that attaches to the T bar. I wouldn't take out the passenger seat and make sure u have a T50 socket. I replaced the whole cable but if u having already done it, it's coming, so do yourself a favour and get a couple of new bushes and fitting kit. About $20 each. Saves buying a new $160 cable. Ford dealers will not tell u this.
@djinn201
@djinn201 6 жыл бұрын
yeah I'm one of those that took off the face shield and thought beuti quick and easy job. Bloody comprehensive vid mate cheers.
@shayneandrew7881
@shayneandrew7881 4 жыл бұрын
You explain everything so well youve taught me heaps luv this chanel thanks mate
@stuff7853
@stuff7853 4 жыл бұрын
Thanks for the kind words mate, glad my videos are helping you out!
@muaythaigoof
@muaythaigoof 5 жыл бұрын
You are a lifesaver this guide was spot on. My GT-P thanks you. Unfortunately I screwed up one of the console clips and lost it. I didn't remove the passenger seat, but yes if I had my time over I probably would
@fucknbullshit
@fucknbullshit 4 жыл бұрын
Dude! what a legend. This is a fantastic video. Removing the seats etc? Mate id have been working this all out for ages. Thanks heaps mate.
@stuff7853
@stuff7853 4 жыл бұрын
Thanks mate! Makes me happy that 4 years later this video is still helping people out.
@fucknbullshit
@fucknbullshit 4 жыл бұрын
@@stuff7853 to go one step further, i assume to change out the gear selector cable i have to un bolt those brass coloured flat headed bolts from the other side of the floor?
@stuff7853
@stuff7853 4 жыл бұрын
@@fucknbullshit It has been to omany years since i had this apart to remember how the cable went in unfortunately. But i kind of recall that it goes through a rubber grommet in the floor pan near the bell housing and then it just clips onto the shifter assembly with a plastic ball much like it does on the transmission end. I haven't changed mine though. Those brass bolts are most likely to remove the entire shifter housing from the car which may or may not be necessary to unclip the cable.
@SimonsRandomRants
@SimonsRandomRants 6 жыл бұрын
Great video. Very carefully explained and plenty of detail.
@stevenantcliff495
@stevenantcliff495 4 жыл бұрын
Thanks for this mate. Very little on here for removing the centre console on our car. Top stuff 👍
@gsncom1
@gsncom1 7 жыл бұрын
Good job mate, that's an easy to follow guide.
@stuff7853
@stuff7853 7 жыл бұрын
Cheers mate
@gregnewberry1147
@gregnewberry1147 6 жыл бұрын
excellent video!!! Thanks for taking the time and trouble to make a quality how to vid. More power to you.
@changinglifeforthebetterjo8997
@changinglifeforthebetterjo8997 5 жыл бұрын
Yes yes yes about time u made my day iv been trying to do that for so long thanku so much finally some1 on KZbin that knows there shit cheers
@davegalloway2841
@davegalloway2841 3 жыл бұрын
Excellent video, very well explained Thanks for taking the time,
@stuff7853
@stuff7853 3 жыл бұрын
Thanks mate, glad to see the videos still helping out years later
@mattshean5308
@mattshean5308 8 жыл бұрын
Good job mate. Doesn't get any better.
@stuff7853
@stuff7853 8 жыл бұрын
Cheers mate
@robertboyd321
@robertboyd321 3 жыл бұрын
Did this today on my sons BA Falcon to replace the shifter cable bush. Stuck on the side of the road in Park. Didn't remove the seats, it's a pain to loosen the handbrake bolts & console rear side bolts, but it's not too hard. Not one screw or bolt in the entire console was tight. The only problem I had (still have) is the handbrake plastic cowl won't go back how it should. Everything else lines up perfectly except for that one piece. In that one spot it looks like the console has moved forward too far because the handbrake pins/claws that grip the drivers side of the console don't line up & adjustment at the handbrake bracket does not have any affect. But it cant have moved because everything else lines up perfectly.
@stuff7853
@stuff7853 3 жыл бұрын
It definitely can be done without removing seats. Back when i did it i wanted to clean under them and also wanted the extra room to climb around the interior so it made sense to do it that way. Not sure i'm following you fully with the handbrake bit. Are you saying the boot for the leaver isn't sliding back on properly?
@stanleymcglashan2625
@stanleymcglashan2625 4 жыл бұрын
Good work very helpful u should do a lot more of them u r good at it n a pleasure to watch cheers stan
@stuff7853
@stuff7853 4 жыл бұрын
Thanks mate i appreciate the feedback.
@jasfirenz1
@jasfirenz1 7 жыл бұрын
Mint bro. So easy to understand. Cheers
@alancooper7062
@alancooper7062 6 жыл бұрын
Thanks for video, I have done this a while ago on my old xt , but this refresher course will help a lot
@NeonblueIndustries
@NeonblueIndustries 7 жыл бұрын
Great vid mate. I wish I'd watched this first before starting the job!! But I'be found pretty much that same as you!! Good to know!!!!
@notevenea8277
@notevenea8277 6 жыл бұрын
Awesum vid bro tryd my luck typing this title in and whala. Wanting to modifiy my centre arm rest to install speakers and raise it higher.
@smithy2
@smithy2 4 жыл бұрын
Thought id fix mine while i had the seat out for recovering, i dont want to take the handbreak off though 🥴 Great vid man 😎👍🏼
@stuff7853
@stuff7853 4 жыл бұрын
Don't be afraid to take the handbrake off man, just put it back in roughly the same spot and you'll be good! Thanks for the feedback :)
@smithy2
@smithy2 4 жыл бұрын
@@stuff7853 i'll take a swing at it, ive gone half way now anyways 😬
@stuff7853
@stuff7853 4 жыл бұрын
@@smithy2 Take your time and you'll be fine. Seems daunting at first but once you've done the job once it's easy
@smithy2
@smithy2 4 жыл бұрын
@@stuff7853 yeh cheers man
@smithy2
@smithy2 4 жыл бұрын
@@stuff7853 job done, lost 1 of the 2 arm rest clips to the void... As i was putting it back in 😒 But i have 2 long (2inch) screws left over and missing 2 short (1inch) screws for the 2 side trim pieces 🤔
@VROllie1
@VROllie1 6 жыл бұрын
Great video, good information and well explained.
@railtrolley
@railtrolley 6 жыл бұрын
Excellent video. I have a BA XR. On mine, the light for the shifter appears to have fallen out of the socket. I can just see the light is working, but not showing the gear shifter position. It's a lot to take apart, just to put the light socket back where it belongs. Handbrake needs adjusting too, so I can do that at the same time.
@richoburn3480
@richoburn3480 7 жыл бұрын
You are a legend this is a well made video. Everything I need to know.
@ChannelGilly
@ChannelGilly 5 жыл бұрын
You're a bloody Legend , Mate . You just made a Shit job a whole lot easier . Thank you .
@geejaybee413
@geejaybee413 8 жыл бұрын
Very informative, good job.
@stuff7853
@stuff7853 8 жыл бұрын
Cheers
@davidstone6819
@davidstone6819 7 жыл бұрын
Very good. Another "extension" to this would be replacing the gearbox to shifter cable as mine just failed (4/2017). Apparently getting pretty common now for the age.
@stuff7853
@stuff7853 7 жыл бұрын
I may do one eventually, mine was giving me trouble when i bought it where the car would display N instead of D on the cluster unless you smacked it into park. I had ford adjust it up and it came good but they said it was at the end of the adjustment. Its been fine about a year now but if it goes again i'll pull the center console out again and film it.
@EDDIEGARAGE
@EDDIEGARAGE 4 жыл бұрын
I found how to adjust the hand brake cable thanks mate
@TheOneWhoMightBe
@TheOneWhoMightBe 5 жыл бұрын
Easy to follow. I am going to have to pull the shifter mech out of my BF since the sequential shift doesn't work and it's locking itself in 1st gear in any gear position. This is *after* spending $500 at the mechanics.
@johngillespie7336
@johngillespie7336 5 жыл бұрын
Great presentation, explained well. Thanks
@Mr00dear
@Mr00dear 5 жыл бұрын
Brilliant job thank you👍
@Bob-4g63
@Bob-4g63 3 жыл бұрын
Great video well instructed. 👍🏻
@stuff7853
@stuff7853 3 жыл бұрын
Thanks mate!
@kingsarm
@kingsarm 4 жыл бұрын
Excellent video thanks its made my job so much easier. One small problem I am having is relining the handbrake holes to where they were. the handbrake unit will not pull forward far enough to line up where they need to be. Any suggestions appreciated.
@stuff7853
@stuff7853 4 жыл бұрын
Sounds like there is tension on the cable from the adjustment handbrake shoes. If you haven't already make sure the lever is in the down position for the handbrake off. If it already is then you'll need enough force to overcome the tension on the cable which shouldn't be to much.. You can bolt it back in a different position though you will likely need to pull the handbrake lever further to engage the handbrake.
@kingsarm
@kingsarm 4 жыл бұрын
@@stuff7853 Thanks for your reply and suggestion. I did manage to get it back in the correct position but would have struggled to do the whole job without your great video. Thanks again Phil
@stuff7853
@stuff7853 4 жыл бұрын
@@kingsarm Good to hear you got it sorted. Glad the video helped!
@jungofett
@jungofett 5 жыл бұрын
Thanks for the info mate.
@mhz1061
@mhz1061 5 жыл бұрын
hell yes, u have helped me out heaps... thank you..
@thereeper9488
@thereeper9488 3 жыл бұрын
Spent a while (one whole week) on getting it out and I find this after breaking three plastic clips under the seat and didn’t even think of doing the bulb for the shifter so know it will be easy cheers mate......also if I don’t have a torke wrench is it safe to just do up as tight as I can get it for the seat bolts
@stuff7853
@stuff7853 3 жыл бұрын
Honestly this is the only time i have used a torque wrench for these bolts. You should be fine i just made a note of it in the video as a precautionary. Hope you got it all back together in the end!
@dylanwilke3700
@dylanwilke3700 4 жыл бұрын
You can get the surround out and back in on an FG at least, it just depends on how how much you persuade the plastics of both the housing and the shifter surround 👍🏼
@martylee5299
@martylee5299 Жыл бұрын
Good vedio. Can you post a vedio on how to replace the heater mixer shaft in a BA falcon or ghia. Then i can do both repairs at the same time. Cheers
@stuff7853
@stuff7853 Жыл бұрын
Thanks mate, if mine ever fails ill be sure to do a video. Everything i film are jobs i am doing on my own cars though so i don't have any mixer shafts that need to be replaced (luckily) there are a few good write ups on ford forums though, hope that helps
@ak47fever
@ak47fever 7 жыл бұрын
Thanks man. This was really helpful
@kiarnastoon6475
@kiarnastoon6475 2 жыл бұрын
I have just realised after watching your video that the pieces holding the shiter plate on mine are missing and new screws added..clearly so they did not have to take out the whole console. I also realised my cup holder is meant to have a lid ...lol...
@stuff7853
@stuff7853 2 жыл бұрын
Sounds like someone definitely made life easier for themselves haha. Luckily 6 years on and i havn't had to remove it again yet. Missing the lid or the updated version without the lid?
@kiarnastoon6475
@kiarnastoon6475 2 жыл бұрын
@@stuff7853 Yeah I think after re-looking at it I have the one without the lid. 6 years? I have my consolde out every 3rd day at the moment..Im trying to get the car back to original condition after shes had 20 or more young 'that'll do' electricians (rough estimate) add and remove upgrades but it has left the wiring almost unrecognisable. I found an ICC earth yesterday spliced in 4 different directions..and Im wondering why Im having issues.....long sighhhhh. Literally every, and I mean EVERY bolt on the chassis was loose..I had my wheel lock up doing 140 when my caliper banjo bolt exited the vehicle and the caliper locked onto the mag. I have spent more time FIXING wires and doing up bolts than driving it..regardless...I love her more than my own children haha
@stuff7853
@stuff7853 2 жыл бұрын
@@kiarnastoon6475 I was lucky with mine when i bought it, it was very run down but everything was original and untouched so the car has never fought me to work on. The barra swapped au i uploaded receantly was like you describe though. I had touched nearly every nut and bolt on that thing in the time i owned it fixing up other peoples rough work. Stick with it though, once you get through it all you end up with a car that you know very well.
@Nunkie001
@Nunkie001 6 жыл бұрын
Great vid mate, cheers 👍
@Michaelkayslay
@Michaelkayslay 5 жыл бұрын
I need to replace the actual stick, the button you push in, to change gears is broken. So it is just tied with a rubber band, is it easy to replace the button thing?
@f_manu3187
@f_manu3187 7 жыл бұрын
big thanks. bloody legend
@mickeyg1973
@mickeyg1973 3 жыл бұрын
Great job!
@panzermacher
@panzermacher 5 жыл бұрын
Do you know how to remove the silver trim tab on the back of the shifter? Mine is all bubbled (same as the surround) & I was to clean it off & replace it with Carbon Fiber vinyl.
@TLE1977A
@TLE1977A 6 жыл бұрын
Dont need to pull the seats out. Thats over kill. And you dont need to torque the seat belts as you dont need to touch them. Ive competed a dual zone clumate control conversuon with the whole dash and steering column out with the seats still in.
@mattjacomos2795
@mattjacomos2795 3 жыл бұрын
you don't have to, but there's some fasteners under the console youcant get to with the sides in place and you'll bust them "popping" the innards out!
@imGlobL
@imGlobL 5 жыл бұрын
Does the handbrake need to be up or down when being removed?
@davidkennedy9024
@davidkennedy9024 6 жыл бұрын
GREAT VIDEO MAN
@chrispharmacis9744
@chrispharmacis9744 Жыл бұрын
6 speed is different just to remove the P,R & N bezel, so much easier!
@stephenstewart5422
@stephenstewart5422 7 жыл бұрын
Gday mate. You would need to do all this to gain access to the gear stick end of a shift cable wouldn't you?
@jonroberts2600
@jonroberts2600 7 жыл бұрын
thank you helped lots
@scottalcorn1973
@scottalcorn1973 7 жыл бұрын
great video mate. do you have any easy fix for that stupid bloody thin rotating plastic thing under the cover? second BA and both have crapped out. get all bent and busted making it hard to move the stick into drive sometimes.
@stuff7853
@stuff7853 7 жыл бұрын
Unsure sorry mate, mine never gave me issues. I assume you're talking about the disc that spins around the shifter when you push it into sports shift? If thats bent i'd say you'd have to pull the whole surround off like in the video. Its been a while now but by memory you can pull the whole thing apart from underneath so you might be able to bend it back into shape.
@wobblysauce
@wobblysauce 7 жыл бұрын
Got the same issue, though I just spin the 'disk' with my finger and all is good again for a time.
@Sleepeasy469
@Sleepeasy469 8 жыл бұрын
Can you take off the top dash area? Want to completely restore interior plastic by spray painting all plastic areas
@stuff7853
@stuff7853 8 жыл бұрын
If you mean the triangle piece above the stereo you can, its held in with the same type of clips as the trim plate around the shifter and will pop off if you pry under it with something. Be careful though as the sun makes them super brittle.
@Sleepeasy469
@Sleepeasy469 8 жыл бұрын
stuff7853 awsome thanks for that little tip, will try that. Also wondering about all of the dash above that. Under the front window area? You thinks its possible to remove that to paint. Im going to put the overline ICC in, ibwant the car to look as modern as possible.
@JackGrow-rz1jl
@JackGrow-rz1jl 5 ай бұрын
How to do the manual one
@mattyclare1263
@mattyclare1263 6 жыл бұрын
Great video but thank god my zf6 speed auto I only need to get to them first bigger bolts then on the chrome bit there is just 4 push in tabs bobs your uncle
@pacificblueit8519
@pacificblueit8519 4 жыл бұрын
I just pulled the centre console out of my 2002 BA without taking the seats or handbrake. Ask me for how to and photos
@truckrod
@truckrod 7 жыл бұрын
Brilliant.
@Eceryn1
@Eceryn1 6 жыл бұрын
good stuff
@nedcampbell6851
@nedcampbell6851 2 жыл бұрын
Geez bro,great video cos I was only fucking around with it all last nite,and the neighbours called the fucking cops cos of my cursing and swearing trying to get it apart. Anyway I did get it apart but I fucken smash the s*** out of the
@stuff7853
@stuff7853 2 жыл бұрын
Damn that doesn't sound like a good night. I hate when jobs go that way. These days i just try to walk away and come back the next day. Saves me breaking stuff hahah
@winzracingNZ
@winzracingNZ Жыл бұрын
All those bolts are in same position E series, with a few inches. Put an AU or B series interior into a E series and find out. 😂
@arealassassin
@arealassassin 5 жыл бұрын
Piece of shit car, made as cheaply as possible! And this is coming from a Ford Guy... They REALLY dropped the ball on the B series, the AU's and previous models were fantastic cars, and easy to work on. The B's are just flimsy shit, if you don't remove EVERY piece of plastic just right, it snaps, tabs break... half of it is broken or distorted FROM FACTORY! And how hard is this console to remove??!! I've never seen such a complicated piece of shit to remove, and the idea of adjusting the handbrake by sliding the lever... utter garbage! My missus wants a Mustang, but I want to wait and see if a yank car is as bad as this end-of-the-line domestic shitbox before we throw down our hard-earned.
FG Boot replacement
15:35
Tom woji
Рет қаралды 4,3 М.
[BEFORE vs AFTER] Incredibox Sprunki - Freaky Song
00:15
Horror Skunx 2
Рет қаралды 19 МЛН
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 53 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 25 МЛН
Torque converter in a manual transmission - will it work?
15:05
Garage 54
Рет қаралды 705 М.
4L60E: 1-2 Shift Valve + 1-2 Shift Solenoid (Part 1) Basic Operation
13:05
Southpaw Autoworks
Рет қаралды 193 М.
Reviving an Abandoned XR6 Turbo: Part 1 Paint Correction
12:28
Notsosoupy
Рет қаралды 14 М.
Steering Wheel Removal and Replacement - BA to BF Ford Falcon
7:16
AC Melbourne
Рет қаралды 53 М.
The Secret Behind Quickshifter: How It Makes Your Ride Faster
12:39
FTS-Simulation
Рет қаралды 228 М.
Transmission Fluid Change - BA BF Ford Falcon
9:33
AC Melbourne
Рет қаралды 112 М.