Sorry about the shaky main camera, I was trying another option.
@bobmacca76025 жыл бұрын
Another great easy to follow explanation of band saw set up. Great for people setting up their first bandsaw and for those struggling with out of alignment problems. It is also a great refresher and reminder for those of us who know this stuff but have neglected checking our saw for longer than we should have. Thanks for another great video.
@tazblink4 жыл бұрын
Just bought a Rikon bandsaw a few weeks ago and the manual said nothing on this adjustment so I used the edge of table to aline to the blade "not as good as your way". I kept looking for good info on this table aline subject but could not find any info on it, no one seems to address this obvious alignment issue when getting a new bandsaw. I am so glad to have found your video it is a much better way of centering the table, not sure why I didn't think of using the miter slot. Anyway this is the baseline that you must start on to tune your bandsaw or all the other adjustments mean nothing. Thanks so much for sharing this over looked first step in bandsaw tuning.
@DavidStanton4 жыл бұрын
My pleasure taz man !
@johngurney10693 жыл бұрын
thank you David just found your video watched so many videos about problem with blade drift not one advised table adjustment everyone failed to fix problem after watching your video adjusted table within 15 minutes had no more problem with drifting blade, so thank you so much for your help. regards john
@DavidStanton3 жыл бұрын
My pleasure John! Tell your friends!
@stevegronsky89045 жыл бұрын
Very nice little video. I'm on the way to my shop to check mine. ****** EDIT 10 minutes later ****** Well, my miter gauge was off by a hair which I fixed. I had just adjusted my fence earlier today and it is within .003" after a cut. I think I can live with that.
@DavidStanton5 жыл бұрын
Sounds good to me Steve Gronsky !
@DRPowell3 жыл бұрын
I just picked up a used 14” Craftsman BAS350 (Rikon clone) from a pawn shop for $169. It is in fairly decent shape overall. The bearings are not smooth and the top is a bit rusty but it’s better than my stand alone 11” Shopsmith saw. (My girlfriend heard it’s bearings squealing and said it sounded like a dial up modem!) I have already adjusted the miter gauge and table top per your instructions which immediately produced a faster and the smoother cut. Once Amazon drops off a new fence, I’ll align it as well and be off and running. Thanks for the tips!
@DavidStanton3 жыл бұрын
My pleasure Dr Powell !
@68HC0605 жыл бұрын
Short and to the point - a very refreshing that does not make one fall asleep while watching. Great video and good style. I don't have a bandsaw, but if I get one, I now think I know all the things I need to know to set it up (watched Alex Snodgrass several times too). I wonder if the 5-cut method can be used for checking and adjusting the table; I have a feeling it might.
@DavidStanton5 жыл бұрын
Possibly would work but on a bandsaw I feel it would be over doing the accuracy.
@68HC0605 жыл бұрын
For woodworking-use it probably would, but if someone is using the bandsaw for precision things like aluminum or POM, it might be a good thing to do while being at it. At the moment, it's possible to purchase a new Sheppach HBS20 for 120 in Denmark (that's an extremely low price, it normally cost twice as much).
@wayneblythe57135 жыл бұрын
Really appreciate little tips like that David, thanks.
@DavidStanton5 жыл бұрын
My pleasure wayne blythe !
@BohumirZamecnik3 жыл бұрын
Thanks for the video. I have to give rotating the table a try. My blade is adjusted with gullets centered but still keeps 1° off the table (and mitre slot) and the fence keeps perfectly parallel to the table and always return to that orientation upon tightening. This might be the last hope to prevent jamming.
@DavidStanton3 жыл бұрын
Hope it works for you Bohumír Zámečník!
@offgridsweden5 жыл бұрын
Awesome video man. Have an amazing weekend, Andreas from Off Grid Sweden 🇸🇪
@DavidStanton5 жыл бұрын
Thank you Offgrid.se!
@SquirrelsForAll2 жыл бұрын
Thanks, Mate! Cracking good video and super helpful!
@DavidStanton2 жыл бұрын
Glad it helped
@navarroedwards80313 жыл бұрын
David thanks for your video on table tips. What is the brand of ear and eye protection that you used in your video ?
@DavidStanton3 жыл бұрын
Hi Navarro Edwards, eyemuffs.
@xcasper19682 жыл бұрын
Hi, great video..any tips on how to make your work surface larger?
@BobLewen5 жыл бұрын
Another great tip, Dave...Thanks!
@DavidStanton5 жыл бұрын
Thanks Bob!
@dusttilldawn1235 жыл бұрын
Cheers David very useful tip and very easy to All the best and many thanks
@DavidStanton5 жыл бұрын
Thanks Harry!
@bobd.4 жыл бұрын
Hi Dave, on my Rikon 10-325 bandsaw, I can adjust the blade guard. They allow me to adjust for plumb and to rotate the guard slightly clockwise or counter-clockwise. There are four setscrews which are used to accomplish this. I like your tips on checking for parallel on the rip fence and setting the miter gauge square to the blade. Have you tried the five cut method with the bandsaw miter gauge that is used for checking table saw sleds for square or is that a bit much.
@DavidStanton4 жыл бұрын
Bob D. Using 5 cut with a bandsaw is a little over the top as far as I am concerned. I bet there are a lot of people out there who will disagree with me.
@jparra47665 жыл бұрын
Excellent video David. Good job.
@DavidStanton5 жыл бұрын
Thanks John!
@michaelleal4165 жыл бұрын
Love the colour of the Eye Muffs, mine are yellow. Very easy to find in the shop as long as they are not covered by something. Thanks for the info.
@patrickmoore21854 жыл бұрын
Can you list manufacturers name of fence?
@DavidStanton4 жыл бұрын
Patrick, it is the standard fence that is supplied with my Carbatec bandsaw.
@andyarsenal67164 жыл бұрын
Thanks Dave, very informative.
@DavidStanton4 жыл бұрын
Thank you Andy Arsenal!
@RamChickPig3 жыл бұрын
David what happened to your Powermatic bandsaw? Did you upgrade?
@DavidStanton3 жыл бұрын
Hi Wooderful! Yes I did. Much better machine now.
@bobd.5 жыл бұрын
Good video Dave. Question: If you have to rotate your table on the trunnion to the limits of the bolt holes, or any amount for that matter, and the table is now square to the blade when the table is at 90 degrees, what happens when you tilt the table on a bevel? Is the miter slot still parallel to the blade or is it now rotated on a plane that is not parallel to the blade.
@DavidStanton5 жыл бұрын
The Trunion is usually factory set Bob. The table SHOULD track correctly through the incline
@CindyL42613 жыл бұрын
This is great info! Thank you.
@DavidStanton3 жыл бұрын
You are so welcome!
@johnlafferty50325 жыл бұрын
Thank you so much. I'll be honest and say the I've never even checked my band saw. It was inherited from my dad and moved many times. I'm almost scared to find out how out of alignment it is.
@DavidStanton5 жыл бұрын
It's probably fine John. I guess your dad would have known all of this.
@hassanal-mosawi60495 жыл бұрын
Thanks for sharing that
@stevei76465 жыл бұрын
Thanks David, will check this weekend. Where did you get your rip fence, I would like to get one. Thanks..... Steve
@stevegronsky89045 жыл бұрын
I have a rip fence that looks exactly like the one on Dave's saw. I'm in the USA and I bought the fence from www.grizzly.com. I actually visited their store in Springfield, Missouri.
@DavidStanton5 жыл бұрын
It does the job for me Steve. It is the standard fence with my saw. I think Carbatec sell them as a spare part?
@stevei76465 жыл бұрын
Thanks David, had a look at the website and they have two options for me to look at. How high is you bandsaw table from the ground? Thanks...Steve
@DavidStanton5 жыл бұрын
@@stevei7646 975 mm but it is n a mobile base. I think standard for my saw without a base is 940 mm.
@SMee675 жыл бұрын
Took me months of back and forth to figure out why I had wonky cuts. 😭😭😭 Overlooked, and or not known about... Mine was the later!
@DavidStanton5 жыл бұрын
It's the simple things Bill Carroll !
@SMee675 жыл бұрын
@@DavidStanton Ha, absolutely Dave! Kind of a "can't see the tree's for the forest" situation... 👀🌳🌳🌳🌳🌳👀
@user-zd2le7ms7l4 жыл бұрын
А как быть если направляющая у каретки имеет люфт и зазор про движении вдоль пильного полотна?
@DavidStanton4 жыл бұрын
Я не могу помочь вам с игрой в руководстве. Может быть, нужно купить лучшую пилу Илья Карасев ?
@callitagain5 жыл бұрын
Thanks mate. Legendary as usual.
@DavidStanton5 жыл бұрын
Thank you omar38317!
@candidosalgado5 жыл бұрын
Hi David. Thanks for the great video as always. Could you please tell which Carbatec model is this ? Cheers from Perth.
@DavidStanton5 жыл бұрын
My pleasure Candido Guerrero Salgado ! It is BS-X3452C
@woodandmetalandstuffpauldo85615 жыл бұрын
Cheers Dave for great info
@DavidStanton5 жыл бұрын
Thanks!
@bluewren654 жыл бұрын
Bloody brilliant, thanks!
@DavidStanton4 жыл бұрын
My pleasure Blue Wren !
@Derek_Lark5 жыл бұрын
Brilliant Dave!
@DavidStanton5 жыл бұрын
My pleasure Derek !
@SilverBack.5 жыл бұрын
Hi David, I have a Delta Homecraft ( 1953 )10" band saw that has NO mitre slot.Two things how can I make a rip fence / crosscut table.Thank you for you video's, the tip and tricks are great.
@DavidStanton5 жыл бұрын
My suggestion is to make a table that fits over your existing one out of melamine. This can have features added to it easier than the existing table.