Bi-directional automatic stirrup bender from bar for the production of stirrups and cut-to-size bars using wires up to Ø 22 mm (#7). 3D version for the production of tri-dimensional pieces. Read More: bit.ly/34xwUNE
Пікірлер: 25
@pilecageweldingmachine3 жыл бұрын
good
@danielzhao79373 жыл бұрын
cool
@inokefono16375 жыл бұрын
So clean??? No dust falling off due to the bend?
@peterparks84874 жыл бұрын
They have that magic rebar, perfect bends everytime
@SchnellSpa4 жыл бұрын
@@peterparks8487 thanks Peter!
@saberhaddad5351 Жыл бұрын
كيف يمكن شراء
@saberhaddad535111 ай бұрын
ممكن رقم الهاتف الوكيل في الجزائر
@saberhaddad535110 ай бұрын
Hello
@williamgubany77243 жыл бұрын
So it doesn't use sprial coil as the main source? It looks like it uses staight pre cut bars. I can only imagine how much waste of tails there will be.😥
@SchnellSpa3 жыл бұрын
Good morning Mr. William, Bar Wiser is a bi-directional automatic stirrup bender from bar. Bar Wiser is the right choise fot the Countries where wire in coil is not available or is too expensive; with Schnell software BarWiser optimizes production orders, minimizing scaps and the cutting cycles. Schnell has a wide range of cutting and bending machines and plants for reinforcement processing from coil. Click here for more info: bit.ly/3jshMMy Best Regards
@bcmiller072 жыл бұрын
It shows the pieces being bent and dropped. No operator grabbing the pieces from the shear itself like we do at our facility. We have the same model. Works amazing minus being right up close and personal. Just be careful I’m guessing.
@michaelhowe7831 Жыл бұрын
Whoever is in charge of production should also take int account what goes to auto benders and what goes to table benders. That should minimize scrap.
@michaelhowe7831 Жыл бұрын
We use 60 foot bars for everything but 3's almost never have that issue. But I also see y your point could would be sweet too lol
@LiL_doge84 жыл бұрын
I want to see this video with epoxy rebar
@LiL_doge84 жыл бұрын
I dont think is that easy
@peterparks84874 жыл бұрын
@@LiL_doge8 should be able to do it. I think they have plastic pulling wheels for epoxy, atleast that's what the manual for the barwiser I ran said.
@michaelhowe7831 Жыл бұрын
We use orange plastic wheels on ours but depending how good the coating is it will crack with those small radius bend
@saberhaddad535110 ай бұрын
مرحبا أنا من الجزائر ممكن رقم الوكيل في الجزائر
@edicsonjosegarate60614 жыл бұрын
Good greeting, I need to know the specification of the machine eura 13 at what air pressure she needs to work and each and every speed of each gearbox that she has, can you help me thanks
@SchnellSpa4 жыл бұрын
Dear Sir, Please send your request to our Call Center: Tel.+39.0721.8787.251 callcenter@schnell.it Best Regards
@shivsinghyadav98593 жыл бұрын
Ryui
@ahmedtarek58643 жыл бұрын
فديوهات طريقه الصيانه الدوريه والصيانه الوقايه
@SchnellSpa3 жыл бұрын
Dear Mr. Tarek, if you need help please send your request to: marketing@schnell.it Best Regards