ANOTHER engine goes BOOM, but what’s caused this?

[@russellhammond4373]

Barum's videos are in good hands with Isaac. Take care Lee.

[@STANLIZ4]

Good job Isaac, very well presented, first class!

[@chascarpenter5006]

Really enjoyed this video Isaac, well done, Hope Lee feels better for Mondays vid..

[@StephenKirker]

Isaac does a great job! See you Monday Lee.

[@woollamiainternationalfilm5285]

Audio was fine. A tiny bit less rich but, perfectly fine.

[@C_Dana]

Lee, sorry to hear you're down in the dumps.....hope your weekend helps to improve things. Isaac certainly did a bang on job today.

[@BarumBTS]

Thankyou 🙏

[@andrewphillips6053]

Nice one Isaacs, Lee hope your weekend gets better.

[@frankp.2831]

Excellent video Isaac. Keep up the great work.

[@davidwhite4518]

well picked up Isaac a good informative video..... hope everything improves Lee will keep watching

[@icarusq]

Best wishes Lee. Look after yourself. I look forward to your videos. And yes, Isaac is doing a great job. 👍

[@eldoradoboy]

yep that def looks like overfueling on the transit... whats crazy is you can usually catch that... you'll hear pretty good fuel knock and likely get some smoke when you dont expect it.... interesting I thought all the perkins were wet sleeve...nice to see some diesels on here.. i havent watched in a while.. i love diesels.. great video

[@Land-of-reason]

Well done.

[@davidsheridan]

That perkins engine is an 1104 series..4.4 litre..in case you dont know you must replace the cylinder head studs..they are stretch bolts..there's also 2 different head gaskets. .standard gasket is used if piston protrusion is up to 15 thou..if over 15 thou a thicker head gasket is used

[@Ibh111142]

Thanks Issac for holding the fort. What’s up Lee? Hope the shy’s not falling in!

[@madeljacky]

Brilliant video Issac, very well put together with the right amount of information, looking forward to Mondays video.

[@BarumBTS]

Thankyou! Hope you enjoyed 👌🏼

[@stevefletcher7531]

The second spring loaded gear is to stop backlash in the gearing system

[@BarumBTS]

Good to know 👌🏼 thanks!

[@francoisvanheerden5920]

Springloaded gears are definatly for anti-bcklash.

[@wimw.8637]

Well done Isaac!

[@Mechautoinsight]

Don’t understand why dirty engine disassembly is happening in your clean engine assembly area. This was not the plan! Please explain! Another good vlog from Isaac. Well done.

[@gregculverwell]

That is called a scissors gear - reduces gear chatter. Toyota uses / used them in the cam drive on many engines and I recently came across it in a 4x4 transfer box.

[@JezCunningham]

"Anti-backlash gears" - same thing I guess?

[@Sir2ofLitre]

Keep your chins up mate. ;)

[@granddadmark7639]

Isaac smashed it 👍

[@mickpickersgill1096]

Well done young man ....

[@stevestone4346]

Fascinating stuff.

[@johnmoruzzi7236]

Glad to see the Perkins jobs are finally under way… will be good to get them on video and gone !

[@MegaReddevil71]

Great video isaac ask Lee for a payrise 😉😁

[@richardhartley1705]

Nice one Issac 👍

[@georgesmith5045]

Hope 🙏 you are okay.

[@ataxpayer723]

Re Perkins paint: Try this: Perkins Blue 33568 Touch Up Paint 400ml Spray Can, Replaces 18324 made by Plastimo.

[@keithlockyer4215]

Great video, re the failure, looks like an injection fault overfueling causing detonation in the cylinder resulting in the piston failure followed by fuel wash on the skirt area

[@mpccenturion]

ALL Great SIR! Thank you all!

[@michaelcooper9279]

Great clip enjoyed 😂

[@daledavies2334]

Sometimes agood smack with an educating iron on the end of the puller will do the trick. You should try Caterpillar steering clutch flanges. They get pressed on a tapered splined shaft under 30 tons to 50 tons load with a hydraulic press. When you had to remove them 5 or 10 years later, you had to just loosen the tetaining nut a couple of turns to keep the pinion from going flying when it broke loose. One guy removed the nut and had 70 tons pressure pushing. Finally a rap on the outer diameter of the flange and the pinion went through a cinder block wall into the parts depatment. Fortunately no one was injured. When the spline released, the pinion left like a shell out of a cannon.

[@davidrogerbinnyi2573]

Is that Perkins a 1000 series ( 1004 ) engine or a later 1100 series as on these the head bolts tighten from the outside inwards and they use a layered steel head gasket ..

[@ambydaly5713]

I have suggested that Lee invests in a hydraulic puller in the past.looks like he still needs one.

[@davidgerrard8661]

Retro Ford do great bits

[@BarumBTS]

Definitely! I was well impressed by it all it’s lovely stuff 👌🏼

[@TamTran-vw7zm]

Video went fine. Try not to stew about whatever the cause of the depression. Don't let the bast*rds win. See you Monday.

[@TCBOT]

thats one big ass block of iron to move

[@chascarpenter5006]

Make sure you have three shredded wheat for brekky..

[@johnburns5783]

If Lee paid you a bit more, you’d be able to upgrade your phone 😂😂😂😂

[@deanbrown9611]

Backlash.

[@davecoleman7431]

Why don’t they use a wood ruff key ?

[@lynjames4306]

Vapromatic is now Owned by John Deere Tractor Company 👍

[@scotttownsley5972]

And yeah.....but yeah.......and emm yeah

[@BarumBTS]

Sorry scott

[@scotttownsley5972]

@@BarumBTS /I was only joking, love all the content from both of you guys :D

[@fatwalletboy2]

Size of that crack!

[@chascarpenter5006]

Said the bishop to the actress...

[@Jester-Riddle]

@@chascarpenter5006 😂

[@Ibh111142]

@@chascarpenter5006😂

[@marcmorris-kb9ry]

Supposdly on the Fords there was software update for piston protection?...ive only done Transits with cracked pistons.....the same engine in Boxer or Ducato ive only done camshafts with slipped lobes,detroyed rocker arms or snapped oil pump chains at 300,000k...im no expert on them but just seem to have seen a few.😂

[@Speedfreak99969]

Who's getting blamed this time?

[@gj91471]

Timing chain should not be tight ? Wasting HP.

[@BarumBTS]

I meant it wasn’t slack, these transits suffer with chain stretch

[@garthp9874]

Isaac did a great job. He is lucky to be learning from the best. It's amazing how many engines you work on. Mechanics will always be needed. Wrenching on things can be used in many different industries. Robots need their innards worked on and is a specialized field that few know about but it is an interesting field. Good Luck.

[@martynashworth1442]

Perkins engines are blue

[@moarif9139]

Do you guys actually build something that works?

[@Deppel57]

Wishing you well, Lee