I have been buying tools from auction that come from Home Depot. Had a combo Drill/Impact kit (new customer return). One of the batteries was dead. Checked the cells and they were all close to 0 volts. Jumpered the cells with a good battery. Voltage came up but still flashing Red/Green on the charger. Repeated this 2 more times; voltage was now about 16 volts across all the cells. Still no good. But now getting all 4 LEDs flashing 4 times when the button is pressed. Jumpered J1 and T1 as per this video on a PBP003 battery. It has the same electronic board as in the video. Pressing the button now yielded a single LED. Put in on the charger and it is charging fine. Thank You for the video and the great explanation!
@ScottYork-tv6jd20 күн бұрын
Just tried the jump with a paperclip and worked like a charm! Thank you!
@justoneperson9 ай бұрын
Larry, you are an absolute genius. Thank you so much for posting this. Worked like a hot dam on my PBP006. I honestly really appreciate it. 👍
@chastalh9 ай бұрын
Good deal! Thanks for posting!🙂
@KenMc19594 ай бұрын
100% Awesome. I had done the jump start and had voltage in the cells, but the charger still indicated a bad battery. I assumed there was a safety on the circuit board but had no idea how to reset it until I found this. It worked like a charm. Thank you!
@thegows12gow8614 күн бұрын
I did the reset I can not believe it worked. Thank you Thank you !
@zkm16jrz11 ай бұрын
I have one of the new ryobi batteries it doesn’t have the t2 j1 to reset it. Any ideas ? Thanks
@adrianmitchell6184 Жыл бұрын
I have an older 4ah battery, it did not have a J1 so jumped to ground. I heard a click, jumped with another battery. It worked! Thanks!
@chastalh Жыл бұрын
Glad you got it going!
@f22coatings18 күн бұрын
SWEET it worked perfect, I shorted the unit then hit the lights , they flashed and I reconnected the unit and booo ya it works !! Thank you!
@catharsisproductions41755 ай бұрын
Hi Larry, I have the exact same battery with the same issue. Battery was fully charged, and the charger shows a solid green light as expected. However, the tester button flashed 4 time and no power is outputting. Opened it up and tested the batteries as shown and getting about 20 volts. Tried the reset jumper, it flashed all 4 LEDs then flashed only LED number 2 and 4 during the jump reset. Am I missing something or is this batter gone?
@andrewzimbardi1784 ай бұрын
Outstanding my friend! My battery is a 3AH so the jumper spots were smaller and a little harder to find. But once I found them and followed your instructions- bam! Light reset and charging like normal. Thanks my guy!
@alexandertagbar30268 ай бұрын
Thank you so much, Larry. my Ryobi battery 18v 4ah working again. I got another 18v with 6ah. I will try this method. Again, thank you so much for your video tutorial. 😉
@chastalh8 ай бұрын
You're welcome!
@rmac2958 Жыл бұрын
You just saved my 6ah high output battery thanks a million!!
@chastalh Жыл бұрын
Your Welcome! Glad it was a help!
@samuelbaez2939Ай бұрын
Hi, I looked at your video of fixing the 18 volt Ryobi battery.. my battery green light all four lights keep flashing constantly and won't stop. What can I do in this case? Thank you
@f22coatings18 күн бұрын
mine did the same and I followed the video, keep in mine, the wires you need are very small, I found a head phone plug in and used them, I did need to use a lighted magnifying glass which was nice. It came back after they were shorted with 2 lights on and I plugged it into a tool and it worked.
@gregtaylor614614 күн бұрын
Wonderful, worked perfectly, many thanks!!!
@tatesweetbrown5222 ай бұрын
Thank you!!! This worked perfectly on my 6ah HP battery saved me $140!!
@bienbalajadia83455 ай бұрын
Soldered a red wire on the positive and a black wire on the negative. Melted two indentation on the back end where I can thread the two wires separately. Closed the cover, and viola! no need to ever open it again. I just have two short wires (so they never touch) I can tap with pins connected to a 12v while on the charger. 😀
@unionse7enАй бұрын
i think you only need to bring the negative lead to the outside since that is the one interrupted by the BMS. Then charge the battery up to some safe level with a voltage supply. The positive terminal of the battry pack is always connected to the OEM (+) tab... i don't think it is usually interrupted. ...I guess your way is a bit different since you are maintaining 12v from another source while using the ryobi charger for the initial charge?...... I think the video on here is possibly even another senario where the BMS has to be reset..... There are probably a few different RYOBI boards
@bienbalajadia8345Ай бұрын
@@unionse7en From what I understand you just have to bring the voltage up so that the charger can get triggered when you insert the battery into it. Battery tend to get fully discharged especially after a winter season where it mostly sit in storage. So far so good. At least I never have to worry about security screws again.
@jinliu9081 Жыл бұрын
Thank you for the instruction! I have the same problem (all 4 check LEDs flashed 4 time), cannot be charged. I used the same method to reset the battery by following your instruction exactly. However, after reset, the problem was still there. Any suggestions? Thanks
@chastalh Жыл бұрын
Sorry it didn't work for you. Does your battery look exactly like the one in the video? Are you sure you found the correct contact points (T2, J1) to short? You may have a bad cell, check the individual cell voltages to verify they are good. You might also charge each cell individually and then try again ( be careful to make sure you have polarity correct when charging). Good luck with it!
@kevinjefferson9739 Жыл бұрын
Hello, very interesting and informative video. I have a P191 3.0Ah battery with the same symptoms, but I could not find a similar reset on the circuit board. Is there any other way to reset this battery? Is it a good idea to totally discharge the battery and try to charge it back (maybe it will reset it)? Thank you in advance.
@chastalh Жыл бұрын
I'm not familiar with that battery so I don't know where the reset would be on that battery. If you totally discharge battery and the voltage goes below a minimum value the charger will refuse to charge it. Sorry not much help.
@crayfish47229 ай бұрын
Same problem here
@PJFinster8 ай бұрын
Great trick, thank you for this! I have the same battery, and it was a full charge, just needed the reset lol
@cjjjjrak Жыл бұрын
Thanks for posting this tutorial video. I was able to revive the 18V Ryobi battery that I had for less than a year.
@chastalh Жыл бұрын
Glad it worked for you!
@MikesManCave11 ай бұрын
If you had it less than a year just return it for a new one
@cjjjjrak11 ай бұрын
@@MikesManCave I should have done that first, but I decided to disassemble them. At the end I tampered with the battery and thinking I have voided the warranty.
@MikesManCave11 ай бұрын
@@cjjjjrak Ahh, yes defiantly voided the warranty. I always try to return stuff first if that doesn't work you have nothing to loose.
@stevebabiak699711 ай бұрын
Sometimes Ryobi customer support doesn’t even want the old “defective” battery back when they send a replacement under warranty. That’s when you can try to revive the “defective” one, after you have the warranty replacement in hand.
@damocsell Жыл бұрын
Thank you very much it did not fix my problem but your description was excellent and at least allowed me to rule out a simple fix.
@chastalh Жыл бұрын
Good Luck with it!
@figurado1 Жыл бұрын
Same here. Did not work but this was a great video!
@tomw7794 Жыл бұрын
Try a different charger. My battery was good ,it was the charger that was bad.
@ThomasPoppell19 күн бұрын
It worked for me. Thanks bro for the video 👍
@ianduffy7146 Жыл бұрын
The battery i have, appears the same, but this repair approach did not work. The battery is PBP004 about one year old
@ajciccone8810 ай бұрын
Same issue here same model.
@colonelcatastrophe4821Күн бұрын
Same here,and this one's maybe been used 5 tmes😠
@sebrura2 ай бұрын
You’re a legend, mate! Saved me mucho dineras.
@averageguy1261Ай бұрын
Ways Ryobi will make you buy a new battery. Thanks for the hack.
@rachidhaddaoui338113 күн бұрын
Thank you, man.did work for me appreciated
@robblack8010 ай бұрын
I have been trying everything to get this battery to recharge. I pulled it apart and checked the actual cells and everything was fine. But the part that goes into the charger read zero. Your video is the one that showed the resetting of the battery. it got to cold. Thank you.
@chastalh10 ай бұрын
You should have about 18 volt if all the cells are good. If you have 18 volt at battery pack but nothing (or very low) at tool terminal then it could be a bad triac, they are the big three lead transistors with an aluminum heat sink on the end of the battery. They are electronic switches to turn the power on. KZbin will have videos on how to check them. Hope you get it going!
@worldwideinterests16 ай бұрын
Great hack but opening mine I find that it's a different control board with no well defined at T2 or J1. Battery has 18+ volts and each cell is about 3.8v but still won't charge so I'm assuming it needs this reset but I'm afraid to start shorting out terminals on a lithium battery unless I know exactly what I'm doing. Thoughts?
@worldwideinterests13 ай бұрын
Follow up. It's been sitting on my workbench for a couple months now and two of the four cells have dropped from 3.8 to 0. I'm guessing a bad BMS because the battery was wet? It's a shame I wasn't able to reset the board because I suspect the cells were still good.
@markmcdermott86415 ай бұрын
Thanks a million, battery is ready to go!
@enriqueayala7593 ай бұрын
i have a 18v 4Ah Ryobi ONE+ battery that stop working. push the battery button and it flashes 4 times. when I try to measure voltage between terminals it jumps from10v to 0v. I went ahead and opened the battery and measure the voltage between terminals at circuit board level and got 18.61. I measure the voltage between the suggested jumper points and got 3.7v. I jumped making sure it was 0v, pushed the button and got 4 blinks and off. close the battery and put it on the drill tool but did not work. I plug the charger and the solid red no green indicator comes up, pointing to the very left where the temperature icon is, but there is no battery on the bay. With 0v across terminals and 18+v across terminals at the circuit board and no working with a tool, I am confused..... is a charging problem or a battery problem ?
@rogerandkristyhart30795 ай бұрын
Fixed my battery. Thank you for the video
@jan-y3f Жыл бұрын
Thank you very much. You saved 2 of my batteries!
@chastalh Жыл бұрын
Glad it worked for you!
@anitamassey34342 ай бұрын
This is a great video but for the price we should be returning them maybe then they will correct the problem.
@Randallgarrett-w6l11 ай бұрын
Does the warranty work even if you didn’t buy the battery new your self but it’s under 3 years old?
@thedeliveryroom45927 ай бұрын
Probably not- it says on the warranty info when you buy it new that the original purchase receipt must be provided to claim the warranty. Pretty sure you have to show a Home Depot receipt or they won't honor any warranty.
@donatasdo10638 ай бұрын
mine ryobi 5ah battery when pushing blink 4 times all green lights, i dissasembled it and made reset like you but it not work , still blink 4 times... i checked volts on battery + and - down there i see 19.72 volts, and when checking up voltage in place were sit in to charger i see 0.4 volts only... up top i checked + i have but negative not come up . when i put in to the charger battery on the charger blinking only 1 red light . battery to hot light.. quess its done....
@ivonnevazquez40982 ай бұрын
Hello, could you please help me? How can I reset the BMS of a 1.5 amp battery? Will you have a video? Please share the link with me. I would greatly appreciate it.
@burn3111 ай бұрын
Worked like a charm! Thank you!
@TheMrRivash3 ай бұрын
Thank you verry much you deserve a like. 👍
@stewartbruce8902 Жыл бұрын
Dear Larry, Working on ryobi pbp005. About 17.5v inside battery and only 0.5v at tower. All batteries show approximately 3.94 except two that read 2.11v I jumped the t2 and j1 but no sucess still blinks and not charging. Please guide me foward as I am determined to make it work again. Thank you for a most helpful tutorial, and all the best from New Rochelle N.Y.
@larrychastain457 Жыл бұрын
Could be a bad triac, they are the big three lead transistor with an aluminum heat sink on the end of the battery. They are electronic switches to turn the power on. KZbin will have videos on how to check them. Good luck!
@stewartbruce8902 Жыл бұрын
Thanks for your reply. I was hoping you would say to simply boost or replace the two batteries that show only 2.11v. I hope I can find the electronic switch video.@@larrychastain457
@test-193 Жыл бұрын
Try using similar method , but different order: 1). Press the test button. 2). BEFORE the LED’s turn off, short J2 to ground. PS- the video shows the correct two pins to connect but incorrectly calls the ground pin T2. The ground pin is not labeled, but you’ll notice that it is a square solder pad, not round pad. Also important to make sure the individual cells are close to each other in voltage or the BMS will just trip again. If needed, charge the cells individually until they all match. Lastly, even if all cells are matched…. the overall voltage needs to be over 15 volts or the BMS will trip again after being reset.
@colonelcatastrophe4821Күн бұрын
@@test-193 I can't find the J2 anywhere on the board. Did to mean T2?
@colonelcatastrophe4821Күн бұрын
Or did you mean J1?
@smotryash11 ай бұрын
Спасибо дружище за полезную информацию!
@chastalh11 ай бұрын
you're welcome!
@Magni11135 ай бұрын
Awesome, worked perfectly thanks
@alancuevas1084 Жыл бұрын
Dude that trick is awesome, you saved my battery, thanks a lot! 👍🏻
@chastalh Жыл бұрын
Glad it worked for you!
@tonylofu1970 Жыл бұрын
My looks like it's sealed I don't come apart what are you do
@larrychastain457 Жыл бұрын
@@tonylofu1970 There are plastic plugs covering torx security screws. You need to remove them to access the screws. Harbor freight has a security bit set if you don't have one.
@neilfixes5501 Жыл бұрын
Thanks for the short-out instructions Larry, but you glossed over that you have press in the top of the two squeeze-tabs to release the case top affer removing the screws.
@TUẤNANHTRẦN-e9jАй бұрын
Thanks you so much!
@KTM500214 ай бұрын
This is for batteries that are out of warranty. If you remove that plug, your warranty is void and you won’t get a replacement battery in your battery might be.
@brucefearon1494 Жыл бұрын
We’ll done , thx . That’s what I needed!
@larrychastain457 Жыл бұрын
Your welcome!
@KE-op4vb4 ай бұрын
Worked good, thank you 😁
@bugkiller52932 ай бұрын
hmmm you described all symptoms perfectly, but reset did not work?
@vfr800ificationАй бұрын
Didn't work for me on a PBP005. Also there is a plastic plug covering the back left screw. I heated the driver bit to melt through the plug since trying to pry it out with a small screwdriver was unsuccessful
@frankshannon32353 күн бұрын
ditto
@DavidCorley-uj6xe Жыл бұрын
How do you know how old the battery is I know you look on the back somehow up you got to be able to read the serial number on it until the year it was made
@chastalh Жыл бұрын
The first four digits are the year and week of manufacturing. For example S/N cs2230xxxxxxxx would be 2022, week 30. I have batteries that are over 12 years and functional. Hope this helps!
@Johnny-tq7bx Жыл бұрын
Easiest way ive seen.. thanks
@peeperGson11 ай бұрын
i have a very old ryobi i havnt used in about a full yr., and from watching this i understood how the circuit board will switch over from blinking red to charging green only after it reads a small amount of power from a battery but initially it does provide a small amount of power with a steady red just as it is plugged in so i plugged and unplugged it about 4 or 5 times with the battery inserted then the battery charger finally agreed to switch over to charging mode with steady red and blinking green light...
@tomtaroni94409 ай бұрын
Your message about not messing with it should have been at the front of the video.
@JohnURHandyman Жыл бұрын
It doesnt Look like you are using the T2 point? That Looks to be the Large Silver/black post labeled T2, just above where you are shorting it on the brd. I did find the J1 point and there are 3 connection ports in 2 square areas of it with that number.and with holes in them. Im not sure where to short J1 to ?
@TONYPEREZ-vl1hx3 ай бұрын
Gracias me funcionó 😊😊😊😊
@b.j.55511 ай бұрын
Is this the same procedure for a 2amp hp battery?
@chastalh11 ай бұрын
Some 2amp batteries have the same circuit board, should work.
@b.j.55511 ай бұрын
It worked. Thank you for your good video.
@chastalh11 ай бұрын
Glad it worked for you!
@markjosephvelado9 ай бұрын
Thank you! 👍🙏
@chastalh9 ай бұрын
You're Welcome!
@jtsokiehobbyandadventures6666 Жыл бұрын
Need to have a cope of register receipt or rybio wout talk to you. I have 2 batters that have done this and no paper work to show when i bought the batteries.
@adame92418 күн бұрын
I have a P197 that doesn't have the T2 or J1 that I can find. Does anyone know how to reset a P197?
@tonygross7575 Жыл бұрын
What if it's an older battery with no self-test button?
@marsbotbyl159 Жыл бұрын
You have 3 arms?
@keeganharmon8595 Жыл бұрын
Indeed he does, a very convenient evolutionary trait to have occur when diagosing most anything. I myself havent reached such maturity yet, praying like hell that i will tho
@johnzmuda525 Жыл бұрын
My battery lights don't work but battery shows 19 volts. Will jump start bring the lights back on when I press the button
@chastalh Жыл бұрын
Probably not, but you can try it won't hurt anything.
@biglon7411 ай бұрын
Surprisingly enough voltage was 26.14 so it's still under 90 day from Home Depot so I'll get another. Just odd that it didn't work. Yes I found T2 and J1 . I get 1 blinking led then after shorting it the LEDs just cycle continuously.
@jimbristolguitar10 ай бұрын
Did it cross your mind to tell us what the security bit size was?
@dananderson74982 ай бұрын
T4 is what I used. This tip worked for me!
@dougbrook62233 ай бұрын
Thank you
@biglon7411 ай бұрын
I did it but leds just keep cycling. What next?
@chastalh11 ай бұрын
Sorry it didn't work for you. Are you sure you found the correct contact points (T2, J1) to short? You might try pressing the test button and before the LED’s turn off, short J2 to ground. You may have a bad cell, check the individual cell voltages to verify they are good. You might also charge each cell individually and then try again ( be careful to make sure you have polarity correct when charging). Good luck!
@job38four1011 ай бұрын
I forgot my 6Ah battery was charging in garage, next day I see the charger flashing red light, I took battery off and pressed indicator button and all 4 light flashes, and it's completely dead. I tried jumping wire from battery to battery but that didn't work....... Since my battery is 11 months old I'll call Ryobi first, if they wont replace it or I cant get hold of them, I'll try your trick............
@chastalh11 ай бұрын
Good Luck with Ryobi!
@alphonsebreaux47356 күн бұрын
You might want to mention the warranty thing at the beginning of the video
@gtakeifer7 ай бұрын
why post this with a good battery?
@marlonsouthall84535 ай бұрын
Bc it wouldn't charge. I'm having the same issue gonna try this
@smallblockchevy10224 ай бұрын
He wanted to give us a visual demonstration of how to do this. For the purpose of a visual demonstration, it matters not whether the battery is good or bad. This good battery, used as a prop sufficiently served the purpose of giving us that visual demonstration. This is why he posted it with a good battery!!! Understand???
@smallblockchevy10224 ай бұрын
He wanted to give us a visual demonstration of how to do this. For the purpose of a visual demonstration, it matters not whether the battery is good or bad. This good battery, used as a prop sufficiently served the purpose of giving us that visual demonstration. This is why he posted it with a good battery!!! Understand???
@tonylofu1970 Жыл бұрын
Mine doesn't have any cruel to take it apart
@oreocreaming2 Жыл бұрын
Wish I could find a 9ah video. There's a t2 but no connection and no j1.
@zozoart3 ай бұрын
It's not acceptable that you should have to do this to a relatively new battery.
@maximusmarine3 ай бұрын
Every vid I've watched tells you to short different circuits
@ComPrt36 ай бұрын
Tried this about 6 times. Never was able to get it to work.
@JonDoe-cg4mr5 ай бұрын
Lithium doesn't like being dead for long
@ComPrt35 ай бұрын
@JonDoe-cg4mr Well, without an autopsy, we'll never know how long it was. 😉
@rogertyler3237 Жыл бұрын
The Test Light Won't Light When I Push The yellow Button.
@petruse88932 ай бұрын
Hate to disappoint everybody,the voodoo doesn't work
@manuelruiz1854 Жыл бұрын
You never showed a defective battery!!!!
@chastalh Жыл бұрын
Sorry, fixed them all before I decided to make video.
@altagraciapolanco7857 Жыл бұрын
no working for me,😭😭😭
@izanami6345 Жыл бұрын
I have 0 v in my batterie help me 😢 please
@chastalh Жыл бұрын
Try taking the battery pack out of the case and checking the individual voltages across each battery you may find you have an "open" circuit (no voltage) across one of the cells, it is bad and will have to be replaced.
@izanami6345 Жыл бұрын
@@chastalh ok thanks
@izanami6345 Жыл бұрын
@@chastalh hi there is current passing through the battery as in your video but by shunting it still doesn't work the 4 LEDs always flash 4 times
@manuelruiz185410 ай бұрын
Yellow jumper wire............
@georgehill9636 Жыл бұрын
Video tubes 😂
@marcosramos4596 Жыл бұрын
All this because I left my battery 🔋 out in the rain!!!