Battery Current Level Indicator

www.utsource.net/ is a online platform for electronic technicians, Makers, Enthusiasts, Kids to find electronic components
tinyurl.com/y2y...
detial.======tinyurl.com/y5t...
A voltage level indicator is a circuit which can show if the voltage input into a circuit is greater than a certain threshold level If a zener diode has a breakdown voltage of 5.1V, after 5.1V or greater is applied to it, it will conduct current across it which can then power on a load.
for more amazmin and easy circuits plz visit www.envirementalb.com

[@johnvafiadis4015]

I would like to suggest something to connect with this project. You could make connect a charger and a auto stop charging. This will be my upgrade to the project. Keep doing this type of simple projects. It will be better from complicated most people doing.

[@gillanidata]

@@johnvafiadis4015 sir are you there plz I need your help

[@ChrisWhiteTech]

So simple yet effective, i'm building this!

[@gillanidata]

Thanx dear plz give me likes on all my videos and also share my videos it will ur sport for me

[@robertoterremoto6105]

greetings from Brazil congratulations great project. Thank you for sharing your idea.

[@gillanidata]

+Roberto Terremoto thanku so much for your appreciation

[@tigerseye73]

Nice video and I like the soothing music.

[@gillanidata]

Thanx dear

[@gustavo4523]

To measure current, or the density of electrons per time, you need a multimeter in "10A", "20A" (depends) in series with positive. Or a clamp meter.

[@gillanidata]

bit.ly/2xLeOtR

[@wellylhakim3619]

The color should be red color for the lowest voltage, and green for the highest voltage. But I ljke this video

[@gillanidata]

+Welly L Hakim Thanx dear

[@frankfurtcarsparencare5737]

Yes

[@gillanidata]

Thanx

[@joewoodchuck3824]

led panel mount 2 wire voltmeters are a couple of bucks on eBay. They only take a few ma to run. Just sayin'.

[@austech360]

Yeah. I agree. In America, that would confuse a LOT of us if we didn't see it wired.

[@electrogamerz641]

Bro I don't make this but my electrical idea said it was real thanks bro

[@rkorko5426]

Good job

[@zz2ale]

This song in background is great!

[@gillanidata]

thanx a lot dear

[@AbdulQayyum-iv6bv]

آج تک کسی نے اتنا صفای سے کوی ویڈیو نہیں بنایا شکریہ

[@gillanidata]

Thanku so much dear

[@yogeshjoshi4719]

Can you explain the calculations, Why we are using 1kohm resistance And for 3.7v battery what value of Resistance will be used.

[@Wisdomofautumn]

Very nice circuit!! Thank you.

[@gillanidata]

U always welcome dear ur encouragement give me power Thanx a lot

[@abuali-ph3ev]

بارك الله فيك يا اخي. God bless you my brother.

[@gillanidata]

+abuali aqrabawi thanku so much dear brother

[@bobtonner]

The title (in English) is totally wrong!!! This is a voltage indicator. Not current.

[@kensrocketry2785]

Most of the current goes to the green led and the yellow led first because it’s closest to the battery in the paralle circuit. Try having red, yellow and green led in parallel while the red led is closer to the input and output terminals and the green led is the farthest

[@gillanidata]

+Iron _Arachnid dear current never stay in first led Because all LEDs are parallel

[@qadeerhussain1274]

Good and simplest job bhai...

[@gillanidata]

Thanku so much for frequency

[@gillanidata]

Thanx for watching my videos dear

[@Naalab]

بارك الله فيك . شرح مبسط وجميل . اشكرك اخي في الله

[@gillanidata]

Plz in english

[@madhumitasarkar5432]

Can this be used for lead acid battery?

[@chauflacorner3811]

Hello Gillani Data. This is great. But I want to use it in my motorcycle. I have had been facing battery problem from last 8 years and this could help me to know the level of battery. I Have a 12 volt and 14 Amp. battery. Please share the circuit. Thanks in advance.

[@gillanidata]

Yes u can use it

[@chauflacorner3811]

@@gillanidata Do I have to add more resistors and leds?? If yes then how many??

[@gillanidata]

Yes u can use more resistor

[@electrodzemix1233]

thanks for the film, I also made the same project and it works for me

[@gillanidata]

thanx dear

[@exwaized523]

If i make 10 LED for the indicator, what value i should used for the resistor? Thank you

[@Multirekachannel]

Thanks u so much for your video, Wa salamualaikum

[@Fox15-q5w]

Buen tutorial (good tutorial), saludos.

[@gillanidata]

+Fox 15 thanku so much for my encourgements dear

[@TheRusssh]

Yeah, just change the video name / explanation of what's happening. As others have pointed out: this does not measure current. This project is not an ammeter. It would show remaining volts in a cell. ... which I don't believe it's hooked up to. I think it's hooked up to an adjustable power source

[@gillanidata]

OK sir I will change the name Thanx for suggestion and guide me

[@KiranKumar-si5xc]

Sorry I don't know English and hindi మీరు చూపించే విధానం చాలా భాగుంది

[@gillanidata]

+Kiran Kumar u know english dear

[@zlackbiro]

I think, you should solder these LED in reverse: input>> RED, RED, Yellow, Green! If he use 1K resistor, that mean we measure current devided by 100 wich is 10v like in this video. If we measure 24v, we will use 2,4K resistor. For 5v, 500ohm! 100ohm per one Volt! Thanks.

[@gillanidata]

Of course u are right

[@johnvafiadis4015]

If is real well done. Small and simple

[@gillanidata]

Thanku so much bro

[@muzammilyaseen606]

If we have big battery .we will also use the same resistors or we will have to increase the ohm of resistor??

[@gillanidata]

no dear you can use the same resistors no need of big resistor plz visit this for full deail bit.ly/2xLeOtR

[@Inquire98]

"Thank You", thank you very much. May I have a copy of your notes and circuit diagram? Let me know. I look forward to hearing from you 😎

[@gillanidata]

Thanku so much

[@KaizenInventor]

Hi you are like a electronics hobbyist. Well on my channel I am looking for such subscribers and we have everything free copyrights for our subscribers.

[@gillanidata]

Yes u can copy my notes

[@gillanidata]

Yes off course

[@faustominuzzo9263]

Grazie, Fausto (Italia)

[@gillanidata]

Thanku so much dear Plz share my videos for my sport

[@anthonycarson8967]

you switched the color of the yellow and green.. Nice!

[@gillanidata]

Thanku so much dear

[@hasibsikder7383]

Thanks good video

[@zagilzag17]

if i want to use it for small battery (9v) i put only 3Led and 3resistor?

[@saleemkk9576]

Can we use this circuit for heavy duty batteries???

[@gillanidata]

Yes can b used

[@nsmadhvendra]

Sir can this circuit be used for 12 volt 220ah acid battery. And Sir, can 10 LED bulbs be put in it to check from 10% to 100%.

[@gillanidata]

yes dear you can use 10 LEDs in this way to check battery then you will have to 220 ohm resistors plz visit my website for my promotion and 2 ads clicks for my sport www.envirementalb.com

[@nsmadhvendra]

gillani data Thanks for the reply Sir. And, Sir can this circuit be used for 12 volt 220ah acid battery.

[@nsmadhvendra]

gillani data Sir, I installed a 5 led and 1k rasistor and connected it to a 12volt 220ah battery. The five led are working but the led is not getting down. Did I do something wrong?

[@fahimasghar6375]

Nice video Sir. But this voltage level indicator not current level indicator am i right? Thanks

[@gillanidata]

Ye u are right dear

[@zagilzag17]

if i want to use only 4 leds for 24V i should replace the resistor to what value? whats the calculations i have to make to know the resistors value for any voltage battery?

[@md.islam8270]

♥La-ilaha illallah muhammadur rasulallah saw.🇸🇦করুণাময় আমার আল্লাহ🇸🇦🤲

[@kerendiy8908]

thx for your tutorial...👍

[@gillanidata]

Thanx dear

[@attilarivera]

This is for 9 volts. Right? it is a very very good idea, my friend! Thank you! 👏👏👏👏👏👏👏👏👏👏👏👏

[@gillanidata]

Dear thanku so much for my encouragement

[@MuhammadAbubakar-se6sm]

v.good i like electronics.

[@gillanidata]

Thanks dear

[@gillanidata]

Thanx

[@MuhammadAbubakar-se6sm]

welcome

[@indianVlogs1993]

excessive power loss due to resistors. use transistor based control for low power consumption

[@gillanidata]

It mat loss of excessive power but very very little and this deficiency can b removed if u use 1st 2 resistors 1.5k instead of 1k

[@جرحوكياطيب-ذ6ش]

Thank You Very Much This is used for 12 Volt Battery or 3 Volts Battery

[@gillanidata]

its for 12v battery dear

[@مصطفىاسماعيل-ش7ق]

Thank you that 's wonderful

[@gillanidata]

Thanx brother

[@sahibzadahabiburrehman2265]

you are best sir

[@gillanidata]

thanx for my encouragement plz must subscribe this kzbin.info/www/bejne/jH3bi6R9aNqAr7M

[@akashchauhan7168]

Please,make a video for 12 v inverter battery.so amazing sir thanks for that matter..

[@gillanidata]

ok dear i will envirementalb.com/led-chaser-with-transistors/

[@mochsaiful9407]

Thank u....good for think.

[@khaleelbinabdulsalam6443]

good starting .go on bro

[@gillanidata]

thanx a lot dear plz watch this video and subscribe this channel kzbin.info/www/bejne/jH3bi6R9aNqAr7M

[@Techvalte]

Nice circuit.... Sir thanks a lot

[@gillanidata]

U always welcome dear

[@f-s-r]

But as the voltage increases, the first led is going to get more and more current, while the last led will get reduced voltage, from all of the previous vf from the other leds. The last led will get like 6 volts less than the first one.

[@gillanidata]

Yes dear this problem can b solved with change in resistors Anyhow this method will not burn 1st led till 30v

[@shaikhamiruddin5848]

You didn't mentioned the use of the Circuit, whitch volt battery to be checked.

[@nastikrewa6757]

Can I use this circuit 12 volts battery in 180 ah

[@reneofngol2398]

Friend can i use only two leds for low and high battery indicator? Tnx my friend.😀

[@gillanidata]

bit.ly/2xLeOtR

[@JamesDaniel7860]

thanks alot!

[@gillanidata]

U welcome dear

[@miansalahuddin5720]

you start series yellow led ............. green led confusion

[@gillanidata]

Mian Salahuddin mian sb you can use any color led

[@gillanidata]

+Mian Salahuddin u can also use more LEDs if you want

[@gillanidata]

+Mian Salahuddin Plz must like and comments my all videos it will sport me

[@itzmrdub4591]

gillani data I'll help you with your grammar, it's not called sport it's called support. Good luck

[@gillanidata]

+Clash With Clans OK Thanx

[@anishbhurke847]

This indicates proportional to voltage from 0-10v Generally battery is 0% at 2-3volts down the full voltage

[@gillanidata]

bit.ly/2xLeOtR

[@moon0094]

nice and simple method

[@electronic_circuits]

go on my friend

[@gillanidata]

+mohmmed farghly thank dear

[@gillanidata]

+mohmmed farghly plz must like and comments on my all videos it will increase my channel ranking

[@electronic_circuits]

ok dear

[@metinozden3095]

mohmmed farghly

[@gillanidata]

dear plz send me the link of your all videos

[@DLSDKING]

This is a circuit which should not be used for measuring both voltage and current. Do mesh and nodal analysis will get the response.

[@gillanidata]

bit.ly/2xLeOtR

[@AngeldeLasTeclas]

Hello, what battery do you measure, what voltage?

[@gillanidata]

Dear i have use 12v variable power supply

[@AngeldeLasTeclas]

Spectacular, this project will serve me in the car. Regards :)

[@salmaarif5117]

Resistors sare same ohm k lene hain..?

[@gillanidata]

yes same ohm fit kam kri n gay thanx for watching my videos plz visit my for my promoiton www.envirementalb.com

[@stephennoriega793]

How to set the resistor if I only want 2 LED, one for the full battery and one for low battery with 5v battery?

[@viejojorgge]

PODRIAS MANDARME UN ESQUEMA O UN PLANITO, PORQUE TRATE DE HACERLO Y EN LA MITAD SE ME COMPLICA, O SI TENES ALGUNO MAS SENCILLO SERIA IDEAL..!! SALUDOS...

[@gillanidata]

Thanx a lot Plz write me in English

[@stabilizerwearingandrepari1804]

Very good

[@alihusein55]

بارك الله فيك و نرجوا المزيد

[@gillanidata]

thanx a lot dear

[@MuhammadRazwary]

جزاك الله خيرا

[@gillanidata]

+Muhammad Razwary thanx dear

[@sasa-iz8kc]

Can I use it for 12v, 200amp battery?

[@gillanidata]

Yes off course

[@sasa-iz8kc]

@@gillanidata thanks for reply bro.

[@technicalsaikat3502]

clean explain thanks

[@gillanidata]

thanx

[@reneofngol2398]

For example, only two led, one for high and one for low? Tnx friend.😀

[@morganasplund7929]

thanx....I realy liked this one. :)

[@gillanidata]

Thanku so much

[@damixkolo4173]

Thanks very good procket

[@gaddigadderiabhotiaworld]

Nice

[@hichamialouani1908]

Thank you. Simple and very useful circuit. Allaho Akbar

[@gillanidata]

+Hichami ALOUANI thanku so much dear

[@talks_by_nisam]

Thanku broooo

[@mdmamunmondol1061]

Is it work on 24 volt 150 AH...!

[@34Gw]

1:24and1:27 is different

[@clearoff8324]

damn . u are right

[@robertoviana514]

Good catch, he obviously reworked the entire circuit.

[@wiwikhandayani5768]

Good eyes

[@gillanidata]

thanx dear plz visit my website for more circuits envirementalb.com/voltage-level-indicator/

[@gillanidata]

envirementalb.com/voltage-level-indicator/

[@music-xi4mi]

Battery voltage idiketar ? Battery level indiketara?

[@Vidya1939]

At the end of video u r using multimeters, and measuring voltage, max 10 v with all led's r lit..u r video title is current measurement. Not the voltage.??? Pse comment. TKQ V MUCH for the novel idea.

[@gillanidata]

Sorry dear my multimeter is faulty Actually voltages are 15 If u want to measure more voltages then use more LEDs in this way

[@aashishsaru5797]

Good Video 😮☺😊

[@gillanidata]

thanx a lot for aprecation

[@sajeevsajeev7423]

Congratulations to you sir

[@gillanidata]

Thanx a lot dear

[@feebyewok]

awesome

[@gillanidata]

Thanx a lot dear

[@feebyewok]

@@gillanidata your welcome brother..

[@gillanidata]

Thanx I'm grwatfull to u for my sport

[@HabibRahman-kw2uu]

bro , thanks!!!!! this is very important

[@zagilzag17]

so if i want to calculate 24V i have to have 8LEDS and 8resistors(1k)?

[@gillanidata]

Ye off course

[@gillanidata]

U can add more LEDs if u want to measure more volts

[@gillanidata]

Yes

[@zakirshaikh486]

sir register Mein plus minus zaroori hai ki lagana plus minus hai ya nahi jawab Jarur dena

[@gillanidata]

Dear resistor Ka +/- nahin hota LEDs Ka plus less zaroori hai

[@SHUBHAMGUPTA309]

Plzz can u explain how its working I understand the process of making this circuit But how do these works please please explain it and explain it

[@gillanidata]

bit.ly/2xLeOtR

[@avijitmitra7906]

sir, can i use it for homemade powerbank during the charging of powerbank battery??

[@gillanidata]

+Avijit Mitra yes u can use it for this purpose But U have to decrease the power of resistor according to your power bank original volts

[@gillanidata]

+Avijit Mitra yes u can use it for this purpose But U have to decrease the power of resistor according to your power bank original volts

[@gillanidata]

+Avijit Mitra use last two resistors 220ohm and first two resister 560ohm

[@avijitmitra7906]

Sir, suppose my powerbank consist of three no. of 3.7v old mobile batteries then can i use those resistors you just replied me ?

[@gillanidata]

+Avijit Mitra then u will have to use low power resisters These resisters are for 12v charger

[@momofpv1371]

Cool.Cool.

[@gillanidata]

thanx

[@QamarShaikh-wf9mt]

Bro It's Not Current Ind ,It's Voltage Indicator 💐

[@gillanidata]

Yes you are right bro

[@gillanidata]

bro plz visit intakeup.com I'm going to post electronics hobby projects here I need your help if you can write some contents for me

[@rakshashankarprajapati703]

Kitne volt ke battery ka battery level indicate kar sakta hai ya bta skta hai sir

[@gillanidata]

Current indicate krta hai dear

[@fabiomelo7646]

Gostei gostei

[@gillanidata]

Plz in English

[@Pertamax7-HD]

Ok sir

[@gillanidata]

Thanx for feedbacks dear

[@mohammedshiri9687]

السلام عليكم مشكور اخي على هذا الفيديو ... أريد أن أشغل 4 مصابيح led ببطارية ... ممكن تشرح لي كيفية القيام و شكرا على الاهتمام

[@gillanidata]

عذرا عزيزي لم أفهم سؤالك لقد استخدمت 4 المصابيح في هذه الدائرة. ماذا تريد أن تغير في هذا ولمزيد من التفاصيل يرجى زيارة هذا المنصب bit.ly/2WpfpPv

[@rozsaferenc1220]

Under the video what music is playing?

[@muzammilyaseen606]

Can we use it with 12v battery?

[@gillanidata]

its for 12v battery dear plz visit in detail bit.do/eRxnT

[@king.....1]

Inverter ki battery se connect kar sakte hai isse

[@gillanidata]

Ye u can

[@rudrajitgoswami9225]

Is it a DC or AC circuit?

[@gillanidata]

It is DC circuit

[@davidizquierdogomez]

Nice ... for What battery voltage is this circuit?

[@gillanidata]

+David Izquierdo Gomez it is used for 12v dear

[@davidizquierdogomez]

gillani data thank you !!! And what capacity in A?

[@gillanidata]

+David Izquierdo Gomez amp does not matter as u want

[@davidizquierdogomez]

great .... thank you....I´ve got a question...I´ve got a NimH battery of 7000mah and it gives me an output of 4V when fully charged. I need exactly an output of 3.8 how can I reduce the output of the batterypack to exactly 3.8V? thanks a lot

[@kashyappatel7224]

Bhai ye bike ki bettery level me chalega?

[@gillanidata]

G HAN CHALY GA BHAI

[@viddeshshravge2445]

Sir can i get resister value for making circuit for 5v battery.

[@gillanidata]

use 560ohm resistor for 5v

[@InvisibleCitizen]

You should also install a momentary switch to activate it as needed or it can still deplete the battery.

[@gillanidata]

U are right