BBS ( Bar Bending Schedule ) of Beam | Reinforcement Detail

[@amanrajput552]

Sir first time kisi ka kush smj aya shukriya sir is trha he smjata rho

[@anubhabroy7550]

Plz make more BBS video it is helpful❤️❤️

[@latheefl2806]

300kg for 10tons was right sir 300kg is 3% of 10000kg.....and thank you so much. u have explained it so well

[@hariomchandra9048]

Very informative video .u r doing very good job .it will be very helpful to the fresher who is site engg .

[@syedaban2233]

This was better than last 30 min video...thanks !

[@akshaythakur7176]

Your way of teaching is awesome and civil engineering looks easy, cool and fun

[@sajid_hussain]

You've taken Ld as anchorage length although for end supports Ld+10d is recommended and achievable in this case. The cutting length, according to you, should be =50*25+13000+50*25=15500 mm. The number of stirrups should be 130 as we place the first stirrup at 50 mm from the face of the support.

[@otiskylo1038]

instablaster...

[@funnh-clip44salltime]

Than you sir please upload again more information about BBS

[@civilsitevisit]

ofcourse brother soon keep watching

[@Erakashkushwaha]

Superb video sir.... kafi नॉलेज mila

[@er.mohammadalikhan882]

Best video on BBS

[@bikashsahoo999]

Very good teaching and calkulation

[@parmarpravin7666]

Very good video.very good B.B.S.

[@erneerajmehra6928]

Very good Explaination Sir ..

[@civilsitevisit]

welcome brother keep watching

[@amitkumar-rv3zc]

Nice video sir jee ..........but lap samajh me nhi aaya.........

[@Oggymeradoggy123]

Bahut accha video Rahul bro

[@civilsitevisit]

Thank you Ae sahab

[@civilsitevisit]

Kaese ho ap

[@civilsitevisit]

koye interview do ek kaese Ae ki tayari yah tips kuch baccho ko

[@harshaltipare8792]

Thank you sir Also share BBS for Column, Footing & Slab..

[@harshaltipare8792]

Please share link of your old video BBS.

[@gadhaviishwardan3971]

Thank you so much best video

[@shaiknoorahmmad6338]

Very informative. ❤️❤️❤️

[@sumanpulamimagar4773]

Sir ye lapping k bare me detailing ek video banayiye

[@ramdeepkumar7616]

Excellent 👌

[@mdsajid-cs1uk]

Sir side me video site ke sath BBS ko thora explain kr dete nug and stirep or compresion and tension ke sath

[@GovindKumar-cw8bm]

thanks sir

[@sajalsharma693]

Very nice content

[@MohdNadeem-hj1wl]

Bhaijan lap length ka topic smajh nhi aya please phir se ek video banaya 🙏

[@Sumit_Sharma.7]

Sir please make videos regarding site engineer vacancy.

[@civilsitevisit]

yes ofcourse brother civilsitevisit.com check here

[@badshah5262]

Waise sir smajh gaya agaya thanks sir

[@ashutoshamanta4966]

Thank you sir but explain pin calculation, i want to know about that.

[@abcdprank]

Thank You so much sir for your given useful knowledge ❣️

[@civilsitevisit]

welcome brother keep watching

[@rohitishte7462]

@@civilsitevisit sir i have dout in plan.. bt i cant explain here.. will u provied me ur email or whatsapl no.?

[@UmerFarooq-km7ee]

Thanks sir i m waiting for this video...

[@civilsitevisit]

welcome brother keep watching

[@sv-yk5gi]

Sir apne bend deduction nahi liya?

[@bittubittu3352]

Very good sir

[@meridunia4740]

Tnx bhai sahab 🙏🙏🙏👌👌👌

[@javedkhan-eu2sx]

Sir mera 1 question hai. Jaise aapne bataya top bars 6.72mtr aur 7.0mtr Lena hai. Hamara bars 12mtrs ka hota hai agar me 12mtr bars se 7 mtr cut karta hu to 5mtr wast ho gaya. Aur 12 mtr se 6.72mtr cut karta hu to 5.28 mtr steel wast ho gaya.mera kehna ye hai ke is tarah steel ka wastage bahut jayada bad jayega?

[@civilsitevisit]

bahi cheez hai site meh hum direct lete hai but rule aese hote hai

[@kingofnoobgaming5809]

Wast ni hoga 5mtr bachta h uska ring bna le

[@divakarsharma5670]

devlopment lenth coloum se start hoti h...ya jha se bend hota h vha se start hoti h?

[@rahulrajan1864]

Thanks sir Sir building drawing me columns layout kaise kiyaa jaaye columns ke beech ki distance kaise nikaale

[@imtajali3723]

Excellent sir ji❤️❤️

[@sadikali1986]

Very nice

[@civilsitevisit]

Thanks

[@takeiteasesolutionchannel6956]

Tq bro nice explanation

[@SKumar-yv4mo]

Thank you

[@vivekjaiswal4411]

Sir ..please make special COURSE for RCC Structural Building design....

[@vivekjaiswal4411]

@Vikram Kadam konsi

[@pavanrathod4868]

Thank you so much sir 💐💐

[@civilsitevisit]

welcome keep watching

[@dargahansda9967]

Nice video

[@civilsitevisit]

Thanks brother

[@frdmlfallthings899]

🥰👍lv u always thnx a bunch sr 👍🤗

[@chanderketurai2696]

Sir box culvert ka BBS banana bataiye

[@shariqueenam8273]

Thank a lot sir g♥️♥️

[@civilsitevisit]

welcome brother keep watching

[@BAWAALVLOGS1]

सर elongation kuch ज़ियादा नी हो जाएगी bar की 100mm(10cm)

[@civilsitevisit]

kya sir smja ni kya puscha

[@BAWAALVLOGS1]

सर इसमें जो स्टीराप है आप बोल रहे है की जब इसमें बैंड देते है तो bar मे elongation होता है 5*2D का तो इस हिसाब से जो हमारी stirup है उसमे 100mm का elongation हुआ है तो मे यह पूछना चाह रहा हु की किया हमारी bar 100mm खींच (elongate )जाती है यही प्रशन है हमरा की 100mm तो बहुत होता है elongation

[@kingofnoobgaming5809]

Sahi h saini sir 100mm elongation jyada lag rha h muje b

[@Rishi-jh2xs]

Thank u so much

[@syedirshad2422]

Hi sir Aap ek doubt hi aapne 400 x400 beam size liya hi Development length 50d ke hisaab 900 mm araha hi To beam depth 400 hi baki 500 kaise adjustable hi Supposed slab height 3m hi beam depth 400 3 - 0.4 = 2.6 ayega column So please explain kijiye

[@amirmaviashaikh7488]

Sir excel sheet pe bbs banana sikhaiye, please

[@civilsitevisit]

zarur bnaunga

[@indic43]

Thank u sir...👍

[@civilsitevisit]

welcome keep watching

[@indic43]

Sure sir.after watching ur channel I got some confidence inside myself.

[@indic43]

Civil site visit sir would you like to upload a vdo of bbs of slab or bridge

[@thejokargaming7526]

sir lapping zone me number of stirrup increase karna prega na

[@ZakirDec]

Sir Lap length kaise liye ho aapne beam me??

[@umashankarsingh1248]

Kindly present this video with side location.

[@SumanDas-st2bi]

Very nice ❤️❤️

[@civilsitevisit]

Thanks

[@satyashrayeesahoo7178]

Sir aap jo bend deduction ke liye 2d yaa 3d bend use kar rahe ho, to kya bend deduction ke liye iss formula bhi kar sakte ho kya? = (No. Of bend × 1.71 × dia. Of bar/1000) plz rply dijiye.

[@civilsitevisit]

but shortcut hai

[@satyashrayeesahoo7178]

@@civilsitevisit sir konsa formula shotcut hai, mene jo bola toh??

[@abhayrajsingh8566]

Great sir

[@nvnshimar9527]

Agr column ka size 400*400 and beam ka size 400*300 to jo ld h 900mm ka usko kaise adjust krenge practically possible nhi h

[@unemployedengineers6537]

Absolutely right please verify sir

[@imranansari5052]

Ld 200 mm ka hota he

[@ramkrishnayadav6236]

Lshape dena padega wahan

[@ShubhamRawat-tj1bi]

U need to work on ur basics bro it's tooo simple 2 adjust...

[@DHANANJAYKUMAR-zm6eg]

Ye column me adjust hoga

[@SN-xc5tx]

Thanks for sharing 😊💞

[@bharatmata8615]

Sir pls pin ke bare m detail se samjhayiyena

[@civilsitevisit]

zarur brother .keep watching

[@aniketraut8167]

Sir..beam bbs krte samy colomn or rest hai to colomn ka konsa area lena chahiye widht or lenght

[@civilsitevisit]

kya brother

[@aniketraut8167]

Sir mera confusion is me ho raha ke beam ke bbs tayar krte samay colomn ka width ka area lena pdta hai ya length ka ,

[@aniketraut8167]

Sir aapka wts number mil sakta hai kya

[@thejokargaming7526]

lapping zone me stirrup ka spacing kitna hoga

[@dharamyadav5157]

Sir steel ki quantity kese nikal te he beam ki jb beam continues hota he ?

[@indun1141]

Thank you sir

[@ambarvohra]

300 kg hi hai wastage 10 MT me

[@mdabdulkhayum1500]

Beautiful sir👍

[@saurabhshinde7519]

Sir Stirrup mi 2 (135°) ke angle hai Or 3 (90°) ke

[@sandeepkirmoliya7783]

Lap dena jaruri he kya beam me

[@navin_kanav]

Lazawab

[@navin_kanav]

Good morning

[@civilsitevisit]

very good morning Thanks brother

[@ermukesh7420]

Thank you sir 🙏👍

[@phonicstory]

4 legged ka bhi bataye.

[@funlife864]

Sir. Beam ki cutting length me 3d less kyo nahi kiya

[@er.deepaksharmabilantri2215]

सर आपने डेवलपमेंट लेंथ में एक ही तरफ के beam का 350mm माइनस किया है जबकि beam तो दो है अपने पास इस हिसाब से हमको 700 - माइनस करना था l डेवलपमेंट लेंथ में से (1250) में से माइनस 700 होना चाहिए था । क्या मैं सही हूं..?

[@vikaskumar-zg1iv]

bhai cutting length me 8 cover blocck aap minus kr diye hain

[@Engineer-dn9kj]

Sir counterfort wall ka bbs batia na , drawing mere pass h.

[@civilsitevisit]

bhejo drawing whatsapp pr bnake dalta hun video

[@Engineer-dn9kj]

@@civilsitevisit ok sir

[@maroofmoon915]

Total cutting length me 400mm kaise deduct hua sir...??

[@debajyotide7398]

In case of top bar 13.72 devide by what?? The value is 7 m

[@sameershaikh-do9ft]

Column was of 400mm×400mm but during the Cutting Length you substracted cover from 300-40-40=220mm...is it a mistake or kind of adjustment?

[@surenlimbu1497]

A

[@surenlimbu1497]

A

[@The-FailedEngineer]

Bbs of column pls.

[@knife5190]

Mujhe drawing dekhna bilkul nai aata plz poora detail me ek video banadijiye

[@sayalimanjarekar664]

Nice info sir❤️

[@mohammaddanishsaifi]

sir apne btaya second bar m lap lenth 1.3xLd lete h but sir apne 7m + 1625 +1250 = 9875 aya or jb 13.72m mai se 9.87 minus kiya to 3845mm aya h apka 4.something kaise agya please tell me

[@amarjeetsharma2398]

Laping in centre and difine Laping distence

[@toshagrawal4629]

Torsion reinforcement site me dalte ho ki

[@debajyotide7398]

Please tell me the calculation of 7 m top bar

[@kunalvishwakarma8848]

Thanku sir

[@sahiransari948]

Amazing ❤️

[@shubhamchaurasia4819]

Stirrup main 90 degree ke liye 1D lenge yaa 2D..🤔🤔

[@rajwantrajbhar5877]

2d lo bro

[@toshagrawal4629]

Crank length slab m kaha se hota h

[@vismayloliyaniya1093]

About lapping I want share some things just for knowledge, if we provide lap either top or bottom suppose in top portion there's 5 nos of steel and at bottom 5 nos of steel and we give each and every steel we give lap at different places not thinking about tension and compression force, we give 1 steel at 1 MTR other @ 2 MTR and etc so each weather it's a tension zone or compression zone only 1 lap will be there in different zones like if we cut section no matter where we would take only one lap will be there is it a good method practically ?

[@halalmeatshophk]

Sir it is very rare than any house would have 13meter long beam, so your example is not very helpful for house building. Most house beam length are between 3 to 6 meter. if you can provide example for this range, it will be more interesting and helpful. thank you. i always thought that the length of Rebar is originally 12 meter, so it is always longer than any beam provided in a house, then why is it still necessary to provide lapping? i just could not understand .

[@tsetenchankarpa7260]

sir i'm bit confused about step1 and step2

[@amdnishar7865]

Sar drawing me sarya kha length kitna ye sab kuch samajh me nhi ata hai kaise samajh me ayega

[@GouravKumar-lc9bb]

Sir mujhe pin ke bare me nh pata kya aap mujhe koi picture vagerah send kar sakte hain

[@Highlightsgyan]

4 ,5&6 Pile GROUP cap BBS WITH HOW MANY DISTRIBUTION BAR Y,Y AND X,X

[@debrajmaity6140]

sir, beam ka size kya h mention kr diijiye

[@badshah5262]

Pin ka aur clear kar dete kis hisab se lena h

[@badshah5262]

Sir pin ka thora clear nahi hua h

[@myselfsubhakshi001]

Who thought from the title that he was talking about beast boy shubh bbs from the title

[@rajum2563]

at 6:10 , remaining length that is embedded in column is 900mm, however the depth of the beam is 400mm only , then how to provide that bar , Can we extend that bar beyond the depth of the beam ?

[@halalmeatshophk]

It is a very interesting question, i also want to know the answer.

[@Balu1689]

Remaining length of the bars shall be embedded into the column

[@rajum2563]

@@Balu1689 ok

[@meridunia4740]

I love you bro