Sahi samjhaya Bhai...aap samjhao ge to aam aadmi bhi engeneer samjhe ga.👍
@chennareddyindla2349 Жыл бұрын
Very very Good, Explained with live construction that is very important to get Idea.
@architectjitendrasharma4638 Жыл бұрын
Thank you sir.Detail me samjhane k liye.
@abdulhakeem76632 жыл бұрын
Thank u sir for sharing valuable information.
@hikikomorihachiman7491 Жыл бұрын
Thank you very much sir.
@vipulsingh86472 жыл бұрын
गर्दा kr diya सर जी
@AshutoshKumar-pq9ud Жыл бұрын
Bahut acha samajh aya ❤
@mahabirsingh92782 жыл бұрын
good video sir
@jatindhiman02008 ай бұрын
One question. Why crank bars and extra bars are not provided in the slab ?
@sandip02maisuriya952 жыл бұрын
Very good knowledge
@shivanjilpathak9186 Жыл бұрын
Why have you not hooked stirrups in 135 degree? None stirrups are visible to be bent at 135 degree with 10* dia hook or 75mm( which ever is greater)
@nikhilchauhan10742 жыл бұрын
Tqq sir
@RajKumar-vw6vi3 ай бұрын
Good 👍
@Damorhemuhimalaydamor Жыл бұрын
Sir very nice video one more I am remember that
@chamanthakur26862 жыл бұрын
good 🙏
@harendrakumarchaudhary2 жыл бұрын
Good sir
@baburamesh9730 Жыл бұрын
Good explanation sir
@Khan-oj8ds2 жыл бұрын
sir during construction bbi lana ek video please sir kya kya test hota hai... kese krate h pre construction list kya hoti during casting kya hota hai please sir🙏🙏🙏🙏🙏🙏
@thegodfather2872 жыл бұрын
thannks great explanation .
@angomgunindrosingh9178 Жыл бұрын
Please make a video on bottom reinforcement.
@chennareddyindla2349 Жыл бұрын
Slab reinforcement, main and secondary bars are provided as mesh, why not provided crank bars or shear bars.
@abduljabbarabduljabbar9109 Жыл бұрын
Thanks Sir.
@sunilpandey62532 жыл бұрын
Thanks sir
@Arifaneesa-f9g9 ай бұрын
Nice
@sauravbasu134410 ай бұрын
Nice, what happens if the extra bars are different on either side of intermediate columns.
@kamleshgoyal93895 ай бұрын
Sir lapping zone ki video m btaya gya tha ki top m lapping centre pr dete hj ,ends pr nhi dete.shi kya h sir
@mallikarjuntandur2 жыл бұрын
hi, how to provide bent-up/ crank bar in two way continuous slab , i mean if the slab size is 40'x60' , there are many beams for support, my question is crank bar can be provided at only in end beams are cranked in every beam, if it is in every beam, rods length is in one length with overlapping or it may be cut sizes according to slab sizes
@civil915 Жыл бұрын
Sir through out steel ja Raha wo column ki steel under Hona Chahiye
@manojmanojsahu4364Ай бұрын
Sir primary beam Anchroge coloum development length coloum outer me hona chahiye but coloum ka center me provide kiya gaya hi videos me
@ReinforceInstituteАй бұрын
Is video banane k tym pe abhi steel arrangement fixing fully nhi huyi thi
@affansheikh25752 жыл бұрын
At point where there is junction of primary and secondary beam but there is no column ( only junction of P beam & S beam) and ...do we have to provide extra top over there or else only continous steel is provided??
@chennareddyindla2349 Жыл бұрын
Good question, but as there is no column no shear force comes. So not required extra bars where P and S beams junction.
@subhamthapa81132 жыл бұрын
what is to be done when the length of development length is still left even after providing 'L'..? should we insert the remaining part into the column or bent it towards beam..?
@hikikomorihachiman7491 Жыл бұрын
I have learned on site that for those cases, we decrease the total length of column below it. Like for a 10’ column, we only cast 9’ column to accommodate the corresponding development length of beam that will be inserted in it.
@vimalkumarsingh85832 жыл бұрын
Sir please send this drawing for better understanding
@Krishna-io7ie5 ай бұрын
Are Bhai sab ek bat btao ye Jo middle me column aarhe h ....inke liye extra steel cut krenge to l/4 k liye cutting length kaha se kaha tk lenge
@ReinforceInstitute5 ай бұрын
There are lots of videos we made regarding this check our full content properly!!
@KishanKumar-zh9ke Жыл бұрын
Sir Secondary beam me Top Extra bar dete hai ki nhi Agr dete h kitna ?
@MAnas-el6cd Жыл бұрын
Bilkul dete hain as per drawing. Iss video me full detail mein checking ni ki hai sir ne. I have worked as an assistant Qc in Pakistan. There is also one thing missing in the video. Apne dekha hoga start walay beam me col ki 1 side py 3 extra thae aur dosre end py 4 extra this is because 2 different beams hain aur jahan per cols k sath 2 beams ayein tou jis ka extra bars ziada hote hain usy hum L/3 per lete haim iss liye dosre end per 3 ki jagah 4 extra liye bars.
@rakeshraturi1435 Жыл бұрын
Sir extra bar sirf top per hi daalte hai ki bottom me v
@ReinforceInstitute Жыл бұрын
Btm mai v
@pankaj64232 жыл бұрын
👌👌👌👍👍👍sir
@ramakumargupta7485 Жыл бұрын
Sir ring ka hook galt hai 135 digri me baniye
@truegaming5515 Жыл бұрын
Sir ring ki band 35' nahi hai
@zafarsk11832 жыл бұрын
Secondary Bheem ka details nahin bataya
@hizbulllahkhattak21842 жыл бұрын
Slab ka bato extra baar
@Krishna-io7ie5 ай бұрын
Jo concept smghne k liye mne video dekha uska answer to Mila hi nahi yr😂