[Tutorial] How to update Flysky FGr4, FGr4S, FGr4P receiver (Flysky Noble NB4 FW 2.0.93, 2.0.99)

[@Johney_Nomadic888]

Frankly, this is the best video available for binding the Noble NB4 w/ Flysky receivers. I'm very grateful for the inside tips. Thank you, sincerely

[@joshuashelton3145]

THANK YOU FROM THE BOTTOM OF MY HEART! I bought a 1/10 RWD RC drift car and man, I was getting bummed out until I watched this video. By the way, I have been following your channel for about 3 years now and I gotta say, you're amazing at what you do! 1 million thank you's 🎉🎉🎉🎉

[@Johney_Nomadic888]

FINALLY, A WELL-MADE VIDEO FOR BINDING THE NOBLE NB4 TO THE FgR4s. THANK YOU THANK YOU THANK YOU!!!!!!

[@codyvirga]

THANK YOU!!!!! Works perfect, I have every vehicle on these receivers and radio. 17 of them, one night I spent hours, thinking there was something wrong, and I ordered more receiver, so I just had it in the wrong port, so take your time!

[@jameshagie9463]

Thank you. You video HELPED me bind my brand new radio to my TAR MT8

[@rep001]

Brilliant, worked perfectly. Thanks for the video 👍

[@jiggs19in]

Can you show a video on how do you updated the flysky noble nb4 to 2.0.93 firmware....

[@BeaversHobby]

It's in this video. kzbin.info/www/bejne/nqW1mGOieqZ8m9U

[@adamshelton9182]

Outstanding!! Thank you!

[@elfreedo]

Thx a lot ! It's very clear

[@allrc8737]

Hi iam new in this hobby and I want to buy this transmitter but I don't see any video talking about the Gyro in the reciver or this transmitter and the reciver has not Gyro bcs I using a radiolink transmitter and the reciver has Gyro integrated please let me know thanks

[@BeaversHobby]

This transmitter only has one receiver with sort of integrated gyro, the GMR micro receiver and the gyro unit is sold separately so it's a separated unit anyway. Unfortunately the gyro for it is very hard to find and I doubt it would be as good as a dedicated gyro unit we use for RWD drifting.

[@Raj_RDX]

Hi boss I'm having difficulty in selecting a receiver for my 1_28 k989 modified for space saving, I have a fs gt3b transmitter?? Which receiver should I use??

[@BeaversHobby]

There's a small AFHDS receiver on GT55. www.gt55racing.com/products/gt55racing-flysky-afhds-micro-4ch-receiver-gtr-29?DIST=RUZBGw%3D%3D There's a version with gyro too. www.gt55racing.com/products/gt55racing-flysky-afhds-built-in-gyro-nano-rx?DIST=RUZBGw%3D%3D

[@Raj_RDX]

@@BeaversHobby once again thank you very kind of you

[@MGK.RC.OFFICIAL]

Hey Beaver, my nb4 noble doesn't have update receiver option what should I do

[@BeaversHobby]

Check the firmware to see which one you are on. If it's an older version than 2.0.93 you will need to update it. Otherwise there is a receiver updater for Windows PC. You can use that too. Here's the link. 1drv.ms/u/s!AjPVS3_BWe3vhSzvxajQ1U43hi6X?e=FCuXnD Here's how to use the receiver updater. It's in the GMR video. kzbin.info/www/bejne/iZutnJ2Op7iJf5I

[@rdrc4586]

Brilliant, thank you

[@isrz8740]

What’s the difference between classic and enhanced mode?

[@BeaversHobby]

The classic is for the standard receivers like FGr4, 4S and 4P. The enhanced mode is for the newer receivers with onboard gyro or other functions like GMR (it doesn't have onboard gyro but it has a port for the gyro module) and INr4-GYB.

[@ChevySSFTW]

Did it come with the bypass plug?

[@BeaversHobby]

Yes, it does. With every receiver that needs the plug to bind, it'll come with the plug.

[@MGK.RC.OFFICIAL]

Hey Beaver, my fgr4 receiver gives me 3 slow blinks and the receiver update bar doesn't move...what should I do?

[@BeaversHobby]

Check if it can bind with the transmitter already? If so you don't need to update. Otherwise there is an update tool for the PC you can try too. www.flysky-cn.com/nb4-xiazai

[@MGK.RC.OFFICIAL]

@@BeaversHobby thanks

[@MGK.RC.OFFICIAL]

@@BeaversHobby what's the update tool ?

[@BeaversHobby]

@@MGK.RC.OFFICIAL It's a Windows PC program to update the receivers. We use it mainly for GMR and Mini-Z EVO but it also works for all the receivers. Here's the tutorial kzbin.info/www/bejne/iZutnJ2Op7iJf5I . Here's the program www.flysky-cn.com/s/Flysky-Reciver-Upgrade-Updater-V1015_EN.rar .

[@armandomorales313]

I have the fly sky NB4 for mini z cars. Can I bind a FGR4 receiver to the radio? I want to use it for my Drag car.

[@BeaversHobby]

Yes, you can. Just select the AFHDS 3 either 2 way or 1 way and you can bind it to a standard receiver.

[@armandomorales313]

@@BeaversHobby escuse my stupidity, where do I find AFHDS 3? Is this a feature on the radio? If so, I went through all the apps on the radio and I was unable to find it. If you can shine some light, I would highly appreciate it.

[@BeaversHobby]

@@armandomorales313 AFHDS 3 is the protocol of this radio. It's not a feature and you don't have to set it. You can select the mode between 1-way (no telemetry, no feedback) and 2-way (with telemetry, basically you will see the receiver voltage and it will tell you if the binding is complete). This is in Model > Radio Frequency Setup.

[@armandomorales313]

@@BeaversHobby thanks for the help. Radio is set but once I turn the car on, the light on the receiver does not blink like it should. The red light stays on and it will not bind. Do you think I have a bad receiver?

[@BeaversHobby]

@@armandomorales313 If you insert the bind plug to the receiver, does it go into bind mode? If not then the receiver is defective. You can also try putting it in update mode like in this video and update it first then try and bind it again. If the transmitter says "binding complete" then it should work, otherwise restart the receiver to see if the receiver voltage indicator appears on the transmitter.

[@arnoudwalrecht8479]

Thanks! Will this protocol work with my ias6b receivers?

[@BeaversHobby]

No, it won't.

[@tonycaudill4750]

I’m having so much trouble out of my Flysky Noble! I upgraded to 2.0.99 and I can only use my Toyota 4x4. I can’t connect my MA-030EVO even if I select it in the settings. Also I cannot update or use the FGr4S V2 receivers. I’ve been trying all morning and all night

[@BeaversHobby]

The EVO will also need the receiver update, the method is the same as GMR: hold the button, turn it on and keep holding for about 10 seconds for it to go into update mode and then update from the transmitter. As for FGr4S, check which plug you put it in. It's the signal side of bind and CH4.

[@JayJay-1985]

I see there's 2 receivers in the box.. is one better than the other ?

[@BeaversHobby]

Not really, they are different types to suite the cars better. The FGR4 is a big one with antenna so it has more range but with the big footprint. The FGR4S is antenna less and smaller so it'll suite a car with less room for components.

[@jannacino5495]

Can you use the fgr4s reciever on to 1/24 scale drift cars?

[@BeaversHobby]

Yes, you can. It's the same 3-wire system just with a different plug. FGR4S uses standard JR/Futaba so for some ESC or servo you might need to convert the plug. Most of the gyros come with both JR and JST-ZH so it'll work wiithout any conversion.

[@jannacino5495]

Thank you im just new in this hobby and i bought a rtr tg racing with generic remote and evrything im planning to upgrade in to better electronincs...but have no idea and i dont have anyone to help me😁

[@BeaversHobby]

@@jannacino5495 My pleasure. Don't worry about the electronics came with the TG Racing car. It's still the same standard and you can replace the transmitter very easily. Remember, the white or yellow wire is the signal and the black wire is the ground. As long as you plug it in the right way and in the right channel, it'll work.

[@jannacino5495]

What about the red?...is there anyway i can reach you out like messenger...if thats fine...

[@BeaversHobby]

@@jannacino5495 The red wire is the power and it's in the middle so no matter how you plug it in, it can't go wrong so don't worry about it. I'm on facebook messenger at facebook.com/beavershobby .

[@andyman8338]

Hey beaver I have a bmrx but when u turn it on and try Ti drift It does circles by itself I have no control when it turns

[@BeaversHobby]

Check the gyro direction. If it turns into the corner by itself then usually the gyro direction is opposite and doesn't counter steer. Next, check the front wheels to see that you they can freely spin even at full lock. Also check the tyres contact as well that the wheels don't lift when you turn.

[@andyman8338]

@@BeaversHobby thanks beaver !! I’ll definitely try this out

[@adriancjones]

Have you tried XRX techstorm yet? Looks pretty cool and it’s a build.

[@BeaversHobby]

Got it a while back, great car to drive. kzbin.info/www/bejne/gaKbd2mZj8uip80 It's my testing platform whenever I got a new motor or ESC because the handling is great. Plastic is a bit soft so be careful when screwing things down.

[@Scottystuntz]

How do you hook it up to your xrx sir?

[@BeaversHobby]

The connection is the standard: - ESC to CH2 - Servo to gyro - gyro 3 wire to CH1 - gyro 1 wire to CH3 or any VR (knob) channel Which receiver do you have? Perhaps you have the FGr4/4S and the plug is not the same? In that case you'll need an adapter or converter to convert JST-ZH plug (small plug from electronics) to JR/Futaba (standard receiver).

[@c.k.hobbyshop3351]

Great video good info 👍

[@johnpaulpagulayan3594]

Thanks!

[@Tatotatin_Rc]

Estupenda informacion, visto en Julio de 2024

[@achraff9748]

Thanks 🌹

[@rc_crawler_zigzag84]

Hi. Very good vid. What news in this updating ?

[@BeaversHobby]

Just need to update the receiver to make it work with the new transmitter firmware. The transmitter firmware has a lot of improvements from displaying channels value, switching between memories not doesn't delay. The other reason to update is to use RM005 module to drive Mini-Z FHSS. kzbin.info/www/bejne/nqW1mGOieqZ8m9U

[@เอมมานูเอล-ล5ฮ]

😊😊😊

[@ElizabethJones-y4g]

Durgan Square