Bell Bullit Hacks, Quieting and adding Cardo Packtalk Slim

[@Jimmyjazz1986]

Thanks for the advice, mate! I installed the same chin curtain and because I could not find a thick enough velcro tape, I used 3x6 mm 3M Seal/Sound dampening tape, wich I applied all around the faceopening. It seals perfectly and is even weatherproof. Now the Bullitt is as quit as it can get..at least like my Bell Eliminator. Thanks again, your video made driving with this helmet so much more enjoyable! Greetings from Germany

[@thephantomsrevenge3883]

The back exhaust vent is where I was getting all my wind noise. I just removed the liner and plugged the hole, now it’s very quiet. Initially thought it was the visor making noise but I was wrong.

[@joancarles749]

Try covering the rear air outlet with adhesive, the change in noise is spectacular

[@matejfilipic8059]

For those who are wondering about breath deflector - it’s Icon Airframe Pro / Airmada Helmet Breath Deflector. My question is: did you have to cut/trim/modify the deflector before inserting it or did you manage to insert it in original form? Thanks

[@h2otoad]

Thanks for posting the brand. Yes, I trimmed the tabs a little bit, as they were too long for the very narrow chin bar.

[@byopedro]

I had the same problem with wind noise, however I found that by holding my arm on top of the helmet that it completely stopped the whistling., the same being if I tilted my head slightly upwards. So I can only put it down to the air extraction slit at the back of the helmet causing most of the whistling.I also velcro'ed completely around my visor instead of the helmet, which also helped a lot.

[@rickt.223]

I have a Bell Bullitt and like it for what it is - an uncomplicated throwback to ‘70s and early ‘80s styling. For longer rides or touring, I have other helmets more suited to the task. If you have to have the Bell Bullitt as your one and only helmet, then these mods are great. But IMHO, they take away from the clean retro aesthetic and simplicity that make the Bullitt’s design so attractive. Also, providing your viewers more information about the items you used to modify the helmet would’ve been more helpful (i.e. manufacturer, model etc).

[@itsdoncartagena6485]

I mean did the look change with those mods? Not at all

[@Minwary]

@@itsdoncartagena6485 it does

[@itsdoncartagena6485]

M M where? the only noticing thing there is, is the cardo

[@jean-marcdejonghe5115]

Just did your hacks and it completely changed my helmet! Thank you!

[@jc_tobal]

where did you get the velcro for the shield? tia

[@MartinZapanta]

I think it would look much cleaner if you attach the velcro on the visor instead?

[@elisecopeland8327]

Thats actually a great idea!

[@asacarrick1385]

@@elisecopeland8327 Or use the rubber tubing meant for sealing window draft. It will provide a better seal and look good too.

[@dukes83]

Awesome video. Thanks for the tips. Modded mine today and it made a world of a difference!

[@scottstambaugh8473]

Great video. Seriously considering one of these, but also the Bell Eliminator. Question: What did you use for the breath deflector?

[@lisacarter7608]

I have that same helmet. I may use some of your secrets to cut down on the wind noise. I also have the SENS 20S evo and I installed it on mine and one on a friends Bullit helmet both in about 5 minutes, just an alternative for communication device.

[@59jaguar]

Hi good upgrades. Where did you find chin curtain? Thanks

[@gcrichlow17]

got links to the deflector and skirt?

[@ivanbvillamil]

Great video! Have the exact same helmet, and the noise is driving me crazy. I have even started wearing earplugs for noise. Could you share where you bought the chin curtain?

[@h2otoad]

I believe this is the chin curtain I bought. It's been a while, and I don't remember it, but I just found it in my list of item on Amazon. hope this works for you. www.amazon.com/dp/B0037NUC2S/?coliid=I3HHSQKXMFR5WM&colid=WZ8OLLO6NE1V&psc=1&ref_=lv_ov_lig_dp_it

[@RichardUttingSharpshootingUK]

This is great. I also put some gorilla tape (black - matches the carbon almost perfectly) over the rear vent. Stunning improvement!

[@TheTeacherjenny]

Thanks for this. Great ideas. How did you make the chin cover? I was thinking that would work for me. This helmet is great on my Moto Guzzi but terrible when I’m riding my Harley. So much wind my eyes water and I can barely breath.

[@h2otoad]

I just used an aftermarket chin curtain that I bought at a local motorcycle parts place. Sorry. I can't remember the manufacturer.

[@tsundokus]

if your still looking for a chin curtain that fits it perfect the one i use was "Shoei Chin Curtain Motorcycle Helmet Accessories, One Size "

[@reinistraidas]

I wonder if they fixed some of the main issues with the 2021 model. Namely the speaker cutout position which was nowhere near my ears when I owned the bullit a while ago

[@elisecopeland8327]

Just happened to come across this comment. Ive got the newer one, just bought about 3 months ago and I can confirm that theyre still nowhere near where they should be! Im actually glad to read this because I was over here thinking that my ears were wonky! 🤣

[@asacarrick1385]

@@elisecopeland8327 Could be both...just kidding

[@jayden1308]

Can you post a link for where you purchased the chin curtain and breath deflectors?

[@Patel-PoDi]

Hi Todd, did you ever made a video of you installing the Cardo Packtalk Slim in your Bell Bullit? If not can you please help 🙏

[@ItsChrisAngeles]

I appreciate the helpful video! I'm curious about how you were able to insert the chin curtain. Did you need to remove the chin cushion from inside the helmet?

[@h2otoad]

I did not remove the chin cushion. It's glued in really well. I just used a butter knife and an xacto to make some room for the fin of the chin curtain to fit. I also used a little spot of rubber cement to hold it in place once it's in. Hope that helps. Good luck

[@ItsChrisAngeles]

@@h2otoadThanks so much!!

[@thisaintsweettea]

I've never really had an issue with wind noise with my Bullit, but the shell itself is loud. Tapping the shell, and even the resonance from my bike's exhaust, is so much louder than it seems like it should be. I assume this is due to the combo of the shell and the hard foam and very little softer materials to deaden the sound. I don't have the same issue with my Bell Eliminator or my Bell Moto 3

[@JosephActivate]

This is brilliant

[@LaminarSound]

Just bought this helmet on black friday. Got a great deal and it should arrive any day. Wondering if I shouldve been more patient and got something like the AGV X3000 or something quieter. Also, Im concerned with moisture entering through the vent holes. Im not sure yet how often I will ride in rain, but seems strange they didnt account for that.

[@giordanino85]

Do you think that a packtalk black would fit in it? Would you send a detailed video/pics where you show what you did on your helmet??

[@kn7583]

Where did you buy those accessories?thanks

[@JWLLMZ]

You have a link to the breath deflector?

[@rickfoy23]

Great video! Thanks brother!

[@linotaffoni2820]

Where can I find the anti-fog chin strap and nose guard for this helmet?

[@tomljc2006]

This video saves the day of so many Bullitt lovers lol

[@nguyenquanavi]

Great vid, great mod, can we have a photo of you wearing it, like to see how it look with the breath deflector

[@mazenaljabri6226]

Nice one, just ordered the same helmet and looking forward to do the same. can you verify to what extend you have managed to reduce wind noise ? 30, 40% and how dose the helmet compare now to others in that since. Last thing, i wouldn't mined an update video to answer all questions for all in more detail , your style is grate and the videos are entertaining. Thanks for sharing

[@h2otoad]

Ya know. I wish I could say it worked wonders... But really, it only made it manageable, because it was unbearable before. I just went for another ride today and thought about the noise. And my verdict is- I can't wait to get another helmet. This is not a good helmet for a daily rider. The cardo system is great, but the helmet really doesn't do it justice. My ears ring after every ride because of the vacuum noise in the helmet. My body temp runs hot, so I enjoy the continued ventilation, and have never felt water leak in when it rains, but I am over the noisiness. I'll try to do more vids. Thanks for the feedback. I've just been very busy lately. Good luck with your Bullit.

[@Nehodin]

Hi! What is the chin guard on this helmet? Have same problem with a wind. Thanks!

[@h2otoad]

It's just a generic chin curtain. You can find them at places like Revzilla or on Amazon. I don't have a model number to share. I just looked around until I found something that looked like it would work.

[@Nehodin]

@@h2otoad 🙏

[@xNlGhTmArEx]

Care to share the Links for the Breath Deflector and chin curtain?

[@h2otoad]

I actually bought them locally at a store called Road Rider, now closed. They are generic products though. I'm sure you can find quite a few on amazon or another site, that will fit well. These were both a tight fit and required some effort to stuff between the shell and the padding. Well worth it though.

[@milodickson1671]

What Velcro tape did you use? Also would you be able to add links for all the things that you have bought if possible.

[@h2otoad]

It's just regular velcro from Depot. I don't have any of the links for the other products. I think I found the chin curtain locally and the breath deflector on Amazon.

[@airoilcool]

BEHIND the ears! That's just ridiculous. I found out the same only after buying the helmet. Looking for advice/guide on cutting out new holes for the speakers. I presume you had to cut the plastic before getting to the EPS. Any problems with that plastic after you cut it (e.g. sticking out, rubbing your head, etc.)? I wish you made a video showing how you did it. Mind making a quick video showing how your new cutouts look and explaining what tools you used and possibly what advice you might have?

[@h2otoad]

I will one day make another video. Seems like lots of folk want to see how to do this. But, it's really not that difficult. I removed the cheek pads, put the helmet on, and then marked where my ears actually were inside the helmet. Then I placed the speaker on the EPS foam and traced out a circle just a bit larger than the speaker. I started removing foam with an Xacto knife little by little to a point at wich the speakers were set in deep enough to not press on my ears too much, but also not be too far away from them as well. I'm not sure what the plastic part you are referring to is. Once you remove the cheek pads, the only bit left is the foam. Glad to help more if you have any questions.

[@airoilcool]

In my helmet there's like a thin plastic cover above EPS foam in that area. I'll take a picture later in broad daylight.

[@connorsurdi3672]

@@airoilcool same. the foam part is where the original mount was supposed to go but it's not close to my ears at all. I got the speakers lower in the helmet but now it folds the shit out of my ears when I'm trying to put the helmet on every time ughhhhh lol.

[@matthewtmoran]

@@airoilcool Did you figure this out?

[@airoilcool]

@@matthewtmoran no, not really :) Did you?

[@adampacetti5497]

Nice DIY stuff

[@CourtneySultan]

i bought that same chin curtain but can’t figure out how you installed it in your bell bullitt. Did you have to do any modification of the plastic tabs or on your helmet? on mine, the tabs don’t seem to want to slide into that space on my helmet. Any help appreciated! 🙏

[@CourtneySultan]

NVM i got it in with the help of a flathead screwdriver to pry open that space a bit but it worked. :)

[@h2otoad]

I used a butter knife to open up a small gap between the helmet and the liner, then trimmed the tabs ever so little before pressing them in. Glad you got it figured.

[@docsmokyalian1397]

Hi, how did you hide the wires from the cardo controller with clip going inside the helmet? Thanks.

[@h2otoad]

I used a butter knife to separate some of the inner padding from the shell. Then stuffed the wire up between the two.

[@JohnJohn-pb8zm]

I have brought a bell bullitt carbon, which is the helmet I dreamed of because of its appearance. However, when I use it, there are too much wind go direct to my eyes! It hurts! Can I ask you for a suggestion? Velcro tape or the chin curtain is more important for reducing the wind going to my eyes?!

[@h2otoad]

I would do the velcro first. Then add the chin when you can find the right fit.

[@JohnJohn-pb8zm]

@@h2otoad thank you very much!

[@riancambangay9210]

how did you carve the ear pockets?

[@mantaskeblis1322]

Can you explain how did you go about relocating the speakers?

[@h2otoad]

Hey Mantis. To relocate the speakers, I removed the cheek pads and then pinpointed where I wanted the speakers to be. After locating the spot I needed them in, I dug out the Styrofoam to the size of the speaker itself, around the location I just marked. I used an exacto knife to do this. I did this at 2-3 different depths until I got it just right. If it is not deep enough it will press to much on the outer ear and cause irritation. If it's too deep it'll be too far away from the ear. I like it close and almost touching my ear, it tends to lessen the surrounding wind noise for me. Once I had it right, I installed the speakers into the pockets of the cheek pads only enough to get them to line up with the new holes I dug into the Styrofoam. Then I put it all back together and tried it out. Worked great. I hope it does the same for you as well. Glad to answer any other questions you have.

[@xXPred4torXx]

Todd Plummer i got the same prob over one Year now... can you please make a Pic from the Inside? Thank you Bro

[@xXPred4torXx]

Now i did it, it was about time 😅

[@keithfoxinc]

@@h2otoad - Same - just bought same helmet - would love to see pics/video from how you carved out speaker openings

[@godoisw]

@@h2otoad I made it with a newer version of the bullit. There is a thin black plastic layer between the foam and cheek pads, but the proceedure is the same, used a kitchen knife to cut the foam and plastic together, positioned the speaker exactly between the original spot and where the cheen strap is fixed on the helmet. Worked just perfect. Thanks for sharing !!!

[@tomje7024]

Hi, what brand is the chin curtain and breath deflector? Cheers

[@h2otoad]

Sorry. Like I've posted several time here before, they are not a name brand, and I found them at a local store. I have no way to chase down who makes them. You'll just have to guesstimate what is out there that may fit and / or take only moderate modification to make fit... good luck.

[@tomje7024]

@@h2otoad okay thanks for the reply!

[@noobcube48]

bell bullit ultra

[@grazryan]

Hi, what visor replacement did you use? Thankz

[@h2otoad]

It was a Bell replacement, bought through Amazon

[@kashmiri911]

What chin curtain is that please thanks

[@romesyoutubechannel5356]

Nice video

[@jenniferlrobert]

i can't seem to find a chin curtain that fits the bell bullit. the link you sent about the one on amazon is no longer available. does anyone have a link to a chin curtain that will fit the bell bullit??

[@h2otoad]

I have a feeling you can use almost any generic curtain. It only needs to be pressed up between the padding and the shell. Just look for one that says it fits multiple models...

[@robothead1024]

Hey what chin curtain did you use?

[@h2otoad]

I bought a generic one from a local Motorcycle shop. But it looks like this one from Amazon would fit. I had to cut down the plastic part just a bit, and force it in around the padding, but it seems to work beautifully. www.amazon.com/AFX-Helmet-Chin-Curtain-FX-39/dp/B00AC6ZF4I/ref=sr_1_22?crid=N0OYRIYLY04W&keywords=helmet+chin+curtain&qid=1569097143&s=gateway&sprefix=Helmet+chin+c%2Caps%2C233&sr=8-22

[@gcrichlow17]

what tool did you use to crave out a new speaker pocket?

[@h2otoad]

I just used an xacto knife.

[@farmboyfanGaming]

This doesnt work. Tried the velcro in the visor and it did not do anything. The real culprit is the vent at the top of the helmet. I tried covering it with tape first and the very loud wind noise was gone 99%.

[@Sir.Veresta]

Anyone find an alternative chin curtain that fits this helmet? The amazon link one is unavailable.

[@h2otoad]

I think this is the one I used. www.amazon.com/dp/B0037NUC2S/?coliid=I3HHSQKXMFR5WM&colid=WZ8OLLO6NE1V&psc=1&ref_=lv_ov_lig_dp_it Sorry for the late reply...

[@Sir.Veresta]

@@h2otoad thanks!

[@gcrichlow17]

How did you insert the breath deflector?

[@h2otoad]

It is the same as the chin skirt. It has some tabs that slide in between the shell and the padding. You may have to slide an xacto knife between them first though to cut through any glue that may get in the way.

[@gcrichlow17]

I went and found the same Icon Airmada, bit it looks to thick to fit into that slot. I used the same velcro that you used at the too of the helmet to stick it inside of the chin bar instead.

[@yinghanzhao6149]

I dug the styrofoam too. Before I did that, the speaker made my ear bleeding.

[@gbntpn]

what do you use to dig out the styrofoam? its seems hard

[@reecedavidson2198]

I used sugru to block the vents which has solved the whistling noise will try the chin curtain and Velcro strip!

[@ingemarkroiss6879]

which vents did you block? on the backside of the helmet?

[@reecedavidson2198]

Ingemar Kroiss all of them, front and back. Used about 5 sachets of sugru. Don’t really care about ventilation I’d just pop open the visor .

[@kwr6100]

@bellhelmets have a look and listen ... fix your hat please

[@ericlarsen7976]

Amen!

[@relevation0]

I can't make myself buy this overpriced helmet with all the wind noise. FIX IT BELL!