How to replace the rear axle seal in a 2015 Chevrolet Silverado 1500
Пікірлер: 46
@geoffcorey22722 жыл бұрын
Thanks for posting this, well explained process. After watching, I have successfully replaced left and right axle seals on my 2014 Silverado with 210000 km.
@BigFrogs4x42 жыл бұрын
Glad to help!
@ThinkAboutIt___3 жыл бұрын
Best example of a axle shaft replacement... thanks :)
@BigFrogs4x43 жыл бұрын
Glad i can help!
@leviscott8519 Жыл бұрын
Great video! This rear axle definitely has some extra process to it. Your video really help with how to go about the stubborn c clip and stubborn axle shaft. Lifesaver!😊
@BigFrogs4x4 Жыл бұрын
Glad I could help 😃
@pmurphy126673 жыл бұрын
the best video I have seen on this after trying to view many others. very well done!
@BigFrogs4x43 жыл бұрын
Thank you
@gregcoles24913 жыл бұрын
Great vid. You were very clear on what to do. Thank you 🙏
@BigFrogs4x43 жыл бұрын
Quite welcome
@stewartfirebaugh26803 ай бұрын
Appreciate the video!!! Just finished up my rear axle seek and your video helped so much!
@BigFrogs4x43 ай бұрын
That's fantastic! Glad to hear it helped!
@dankeller31642 жыл бұрын
Awesome video .... Thank you for taking the time to post this and give the extra hints and suggestions God bless ... Love the verse ... Cheers
@BigFrogs4x42 жыл бұрын
Thanks I do these to help people when I can.
@austindavis91183 жыл бұрын
Thanks man had the same problem with 2012 Chevy silverado had to use a chisel to move the axle far enough to get the c clip out
@BigFrogs4x43 жыл бұрын
Hope it helped you some. Thanks for watching.
@gregvaldez22 Жыл бұрын
Use c clamp on hub and other side of c clamp to where the brake caliper bold hole is on the axle and it will press the axle in far enough to remove/ re install c clip. Had same issue
@MartinezTrucking Жыл бұрын
Very nice video. You should do a video of the parking shoe replacement next.
@BigFrogs4x4 Жыл бұрын
I would but it's not my truck and the guy who owned it traded it for a newer ram with air ride suspension. Sometime in the coming months he has me installing a bds 4" lift on it.
@jeremypyottjr78352 жыл бұрын
Agree with the RTV on the seal. I'm doing mine this weekend coming.
@BigFrogs4x42 жыл бұрын
Good luck. Fun times!
@TrailAdventuresTV4 жыл бұрын
Great vid! Can't wait to put a strait axel under the front of the ZR2. Nah just kidding.. Have a good one brother.
@BigFrogs4x44 жыл бұрын
I was looking at mine a while back. It's doable lol
@BigFrogs4x44 жыл бұрын
Whens your new video coming out
@TrailAdventuresTV4 жыл бұрын
We have a trail video coming out in a few minutes. However it’s not with the ZR2. Wifey wanted to drive her Jeep.
@BigFrogs4x44 жыл бұрын
No problem. I like your videos anyway
@georges45624 жыл бұрын
Great video ! How’s the ZR-2 ? I just bought a 2020 and loving it so far.
@BigFrogs4x44 жыл бұрын
It's good. We primarily use it for long trips now since my wife has been working from home.
@bcar1ify2 жыл бұрын
No need to put anything on the gasket. I reused mined after a fluid change it is fine.
@lambertsaldi15504 жыл бұрын
Great Review thank you 👍🇺🇲 The Vermonter
@mikeo.15936 ай бұрын
I suspect I have a very small seal leak on my 3500 srw would it better to replace or just keep an eye on fluid level
@BigFrogs4x46 ай бұрын
It will need replaced if it's getting anywhere near the brakes. Some states it won't pass inspection. But yes, keep an eye on the fluid level. Rebuilding a rear differential is very expensive.
@miguelortiz58642 жыл бұрын
Great video men, do you know the torque spec for the cross pin bolt?
@BigFrogs4x42 жыл бұрын
I'd have to Google it. I have done so many i go by feel. Never had 1 come out. If you can't find it let me know and I will look for it.
@mxrevival2 жыл бұрын
Good job dude
@BigFrogs4x42 жыл бұрын
Thank you
@sharker1613 жыл бұрын
So I’m to the point of turning the driveshaft to release the pin and it will not turn more than a few inches in both directions..Any thoughts? Yes i’m in neutral
@BigFrogs4x43 жыл бұрын
So driveshaft wont turn?
@BigFrogs4x43 жыл бұрын
Put transfer case in neutral if you can. If you have the calipers off don't hit the brake pedal
@dw19852 жыл бұрын
I have to do this on my 2001 S10. Any idea how much a shop would charge to do it?
@BigFrogs4x42 жыл бұрын
It is hard to say. Depends on labor rate and if all goes well. No rust etc. Although I think the s10 is easier.
@dw19852 жыл бұрын
@@BigFrogs4x4 Can you take n educated guess, ballpark figure?
@BigFrogs4x42 жыл бұрын
If charging $70 per hr then 2-3 hr labor. Are they doing 1 side or both. 1 probably closer to 2 hr