Bikeshield Brompton Frame Protectors

[@LiveSteamMad]

I just bought this and applied it to my year 2020 H6L in Black Lacquer. A few things I learned... do NOT handle the sticker when it's off from it's backing. Instead, cut out (around) the sticker from the backing with scissors, then offer it up to the frame in order to work out the best fit, then peel one edge back very carefully with a finger nail whilst NOT putting a finger print on the sticky edge, then apply about 1/2 inch of it in one place and then unpeel gradually until you get to the other end, whilst holding the unpeeled end against the frame, moving a finger along the part that gets stuck down, from one end to the other, along the middle of the sticker. Whilst doing this, gradually press down and feed a finger along each side of the middle to stick it down gradually and take your time, it can be done with no marks or air bubbles but takes quite a while to do. I worked this out because when I applied the first sticker I got all sorts of finger grease along the edge, you learn from experience... Also, it's 10x times more difficult to do this sticker application with a dark color frame because it shows every last little piece of dust and fingerprints etc if you get it wrong! Some of the decals (like the chain stay ones) didn't conform to the curve so I had to slit them, and some of the cut outs didn't quite line up with the parts on my frame. The head tube sticker goes on the handlebar stem, I believe! The instructions were terrible (i.e. there were none). All in all I would give the kit a 3 out of 5.

[@brilliantbikes]

Thanks so much for watching and for the pointers

[@suzykinsman5111]

Using a hairdryer when applying from the middle helps the sticker become slightly more pliable so you can squeeze out air bubbles easier

[@robinferguson8911]

That made me anxious just watching! I've always consoled myself that scratches just show I've had adventures with my gear, and gear is meant to be used.

[@brilliantbikes]

That’s about where we are, but thought we’d give it a go!

[@JulieGirard]

Since I just recently got my new Brompton P-Line Electric, I am grateful to you for passing along these useful products! I am ordering mine now! - and, of course, love the outtakes!

[@brilliantbikes]

Thank you so muchB they are not to bad to fit at all, just practice I’ve on a little one first!

[@cirodirosa6752]

Thank you for wrapping my present with care. Much appreciated!

[@brilliantbikes]

lol! Thanks for watching!

[@danielaelmi]

Great vid! The explanation of where stickers must be applied is really useful!

[@brilliantbikes]

Many thanks! We thought it was not that easy!

[@finncarlbomholtsrensen1188]

As an owner, you are able to buy carbon sets specifically for protection of the Brompton Frame. Below the Crank and below and on top of tube with the chain, which will prevent most scratches! Also below the cables on the fork (to be bolted on) and the front of the frame, with the wire holder. If wanting a little extra, leathers for the frame and the stem post, to be sown, or using Velcro. If so your bike may look as original, even after years of use, - unlike if not cared for. Finn. Denmark

[@brightlightdun]

Thanks for the sharing. I think it is easier to apply the tapes when the bike is unfolded.

[@brilliantbikes]

We agree hence we unfolded it for most of it. Thanks for watching!

[@raymondii436]

Oh very nice. I used this brand and put some on my road bike, but having a brompton specific kit is really nice. I don't think you really need to cover the entire frame, I wish they had a smaller kit to cover the essential parts.....just the parts that are likely to get scratched, and definitely where the cables rub. What I like about this brand is: 1) the vinyl is quite thick...thicker than I expected. 2) the adhesive is relatively weak, it's very easy to peel it off, and it absolutely leaves zero residue when you peel it off. Other types of adhesive tape will get gummy when you remove it.

[@brilliantbikes]

Many thanks for watching! We also agree and found it easy to fit and remove if we wanted to.

[@anthonylloyd6094]

Ooooo, they look like a good investment. I am also intrigued by the tread on the Schwalbe tyres...

[@brilliantbikes]

What these ones: brilliantbikes.co.uk/brompton-tyres-tubes/5696-brompton-schwalbe-almotion-16-inch-naked-wall-tyre.html Our next video

[@Pesmog]

This kit looks to use a good quality wrap which is key to doing this well. 👍I have protectively wrapped my last seven bikes, sometimes shaping, cutting and fitting the pieces myself (a long job). Other times fitting them using pre-shaped kits from various manufacturers. I now prefer to use Invis kits, who are slightly more expensive than the kit shown in this video, but I find the quality of their plastic and their customer service is very good. They sell two different kits for Brompton, based upon the bikes age, and are made in the UK. When applying the wrap I prefer to apply it wet with clear baby shampoo mixed with water. In my experience the higher quality plastic films are far more forgiving of you making errors and having to remove and refit them. The cheaper plastic films, including Gorilla tape however are not.......👍

[@brilliantbikes]

I was really impressed how easy bit was to apply! Thanks for the suggestions!!

[@GregoryHanson1]

Excellent, as usual. We have used leather protectors, but may get this for my wife’s Brompton.

[@brilliantbikes]

Many thanks! The leather straps do look cool!

[@GlobalAdventurer]

I used GM frame protectors that you cut to fit. Works wonders. But, in a few years I may remove them and get this Brompton specific one. They were very tedious to apply but they definitely work against rubbing and scratches. I believe if Brompton owners only put them on the main frame and at the cable rubbing points would be a way to keep their bromptoms looking new for years. I can't see having a Brompton that's not covered and protected. Thank you for this video!👍

[@brilliantbikes]

Many thanks for watching! I was impressed how easy they were to apply!

[@KennethWuAU]

I ended up cutting my own using car panel protectors. They use a wet application method, you can easily reposition them if you align them incorrectly. For the template, I based it off this product and digitally scanned it. As for the cutting, I’m lucky our office has a vinyl plot cutter.

[@GlobalAdventurer]

@@KennethWuAU That sounds like the way to go. Thanks for the info👍

[@Donkaestner2634]

Nice , thank you. Apropos protection , can we please get an 2 year update on the Continental Contact urban tires . That would be very nice . Thank you an greetings from Germany 🙂

[@brilliantbikes]

Hello! Great idea! I’ve still not had a puncture!

[@Donkaestner2634]

@@brilliantbikes Perfect , thank you for this rapid answer , it helps a lot . Time to upgrade my Racers !

[@josephstafford7760]

In the video you mentioned the head tube. You stated that the sticker was too big for that area. Did you ever use that sticker. I did apply my as it was to large as you stated in the video. Thank you for identifying all the other areas. I don’t think I would have ever figured out the proper placement. As for the air bubbles, I was pleasantly surprised that they did disappear after about 9 days for me. I was rather skeptical after the first days as there appeared to no change. I live in Tampa Florida and it get very hot so I left the bike in the hot sun for several days and magically the air bubbles disappeared. Thank you for a very informative video. I couldn’t have done it without you.

[@brilliantbikes]

Thank you for watching! So glad it helped! If I recall I cut sticker to a smaller size and fitted it whee it was needed

[@markhooper5824]

Very interesting. Think I will go ahead with these.

[@brilliantbikes]

Many thanks!

[@finncarlbomholtsrensen1188]

When I had first bought my by then Top, Flame painted 2019 "SuperlightM6LXBrompton" during High Covid19, for the vacation money saved, I gave it a full Autopolish all over for protection! I then realized that after - two or three folds, that the Clear Tape - "Protection"🤔(sadly its only from the Brompton Factory), had nearly been worn through to the paint!!! So I immediately ordered what I could find of "Carbon Protection Plates" and a Shield for the fork, from the main suppliers of "Useful Brompton Accessories": China, Korea and Taiwan! Also some leathers, to be sown on for my frame - and stem post. It is honestly a Sad Story, that after all those years of production, that Brompton still haven't found out how to keep the frames paint looking fine, as mine, for those with a liking for a "nice looking bike"! I have latest ordered a small "P shield" for below my Cable in front, as this is now the Model closest to mine, it seems? Finn. Denmark

[@finncarlbomholtsrensen1188]

When I got my 6 speed, I wondered for what use I had the low gears, til I met an absurd hill and had to walk on top, on Danish, Bornholm. So I wouldn't know for what use I would have - the coming 12 gear version, which seems to be intended to replace the former 6 speed? But I could as well add a double chainwheel in front, or a lighter, 7 speed chain-wheel and single changer, as it is possible to buy from Asia, for a Brompton? Finn. Denmark

[@brilliantbikes]

Many thanks for watching and for the suggestions!

[@scoops2007]

As mentioned elsewhere here, a called RideWrap make a Brompton specific version - one for each type of Brompton. Going just by conversion rates, it is over twice the price but is applied wet and comes with all the solution, squeegies etc. you need to apply it. There are some reviews on here where it is being used on mountain bikes... but it would be interesting to see if there is much difference between the two.

[@diane1959]

Good job. As always, great video. I have used helicopter tape for years to protect my bikes. About one year ago I used this particular brand of tape for my new Brompton. I sprayed some soapy water on the back of the tape and on my hands before I applied it to the bike. It allows the tape to be moved around to place it properly. I squeege out the solution along with the air bubbles. It's more work but has worked well for me.

[@brilliantbikes]

Ooohhhh great suggestion, next time. Thanks for watching!

[@danhoang6335]

Good suggestion! In fact, I have used the same method to apply decals & film protection to my bikes. Just put a drop or two of dish soap in an 8oz spray bottle, spritz it over the frame and decals then you have plenty of time to apply. Also doing it while the bike has been conditioned at room temperature.

[@pinktoebeans]

@@danhoang6335will dish soap not rid the adhesive from the tape as well?

[@evil_cb1859]

Although I like to look after my bike, I’m not sure I’d go so far as to virtually cover it in plastic film. I do, however, stick a ~50mm length of electrical insulation tape on top of the rear of the chain stay to prevent damage from the chain when on the small cog. Seems to work well.

[@brilliantbikes]

Thanks for watching! I was surprised how easy they are to install

[@helenbenjafield7351]

I thought of plumbers' tape,because there's no residue.

[@lpmturner]

I've tried 3M Scotchgard. It worked well to keep my one glossy Brompton "prophylactically protected" :) but this Bikeshield seems better if for no other reason than the pieces are pre-cut. Any idea how well it works on a matte finish (esp. the textured finish on the CHPT3v2)? Thanks for sharing.

[@mongteck]

When we do wraps and film sticking, aren’t the spray soapy water is the standard way? Once u paste and pull it out due to alignment , the sticker will leave that mark on the glue side

[@brilliantbikes]

Many thanks for watching. The protective stickers take longer to stick if you apply them wet.

[@nicekit]

Hi H in singapore, we have protector wrapper company that wrap the brompton beautifully without any crease or gap.. It looks as if there is no wrap

[@syedhusen]

Yes. I did it for my Chpt3 V4 here in Singapore too. Far much better than bikeshield stick on method. Btw, in the video the bike should not be folded when applying the shield.

[@brilliantbikes]

Sounds amazing!

[@christianspeck7110]

I put these on a few years ago. I can report that yellowing has been no issue. Dirt creeps in from the side, which is not pretty on a clean bike. That said, good protection from scratches.

[@brilliantbikes]

Thanks! We thought it might over time. We will report back!

[@josephstafford7760]

Did you have to do any disassembly. I have seen videos in which to person disassembled to bike to apply the stickers.

[@brilliantbikes]

Thanks for watching! No we didn’t on the bike unfolded

[@carolinepaige217]

Thank you for the video. Long term have you been happy with the staying power! Also, do you sell the kit for a P Line 4 speed electric, Gloss? Thank you

[@brilliantbikes]

Thanks for watching! We also use them on our MTB and they are great, they can get a little dirty at the edges. The one we have, is suitable for the P line and electric, but does not stick to the forks or rear triangle as the paint is a little lumpy. brilliantbikes.co.uk/brompton-sundry-parts/5709-bikeshield-full-brompton-kit-gloss.html They are on order and due in next week

[@grahamlongley8298]

If you do not want to go the full monty use mylar sail repair tape. 3 metres 150mm wide costs >£20 they also do 50mm & 100 mm wide. Does the job just as well . Obviously it does not come cut to shape though. But if you just want it for protecting small areas it can be a very cheap alternative. Plus you can repair your sails & model aeroplanes as well😁😁😁

[@brilliantbikes]

Many thanks! I guess the cut to size was the thing that makes them super easy to fit! I recon they only took 30 minutes to fit! Not bad!

[@pierrerreip]

HI thank you so much for the info about the existence of this product and the video. IS there a guide with the kit to tell the user where each sticker goes and how?

[@brilliantbikes]

Yes, we added a photo on the product to show where the stickers go. Some of the packets also have this in them. Thanks for watching!

[@martin_emrich]

Try spraying the bike and the adhesive side with water mixed with a tiny bit of dishwashing soap (to make it more slippy) and some ethanol/burning spirit (to make it dry faster). Then you can put on the stickers any way you want, then shift them in place, and squeegee out the bubbles to the sides. The water will dry off, making the sticker stick.

[@SingaporeUntold]

THIS

[@brilliantbikes]

It will take longer to dry if you do this. But may be easier.

[@KennethWuAU]

I purchased this a while back, but wasn’t convinced of the film’s quality. So, I traced them to build a cutting template and ended up cutting my own using quality 3M car panel self-healing protection tape. Luckily, I had access to a plot cutter at work to do this. I also opted to cut my own so I can use a film that supports a wet application method, which is easier to readjust if you make a mistake.

[@LLF1234]

How's the 3M going for you so far? I've read some places that by using water it might trap some moisture and after a few days the spots under the tape will rust. But it doesn't seem to happen to everyone, luckly most doesn't.

[@KennethWuAU]

@@LLF1234 My stem showed some patina after wrapping. But it quite even. I think it's more from the UV exposure from the sun. My main frame is still looking as good as new after 4-5 years of regular use.

[@richardforster1239]

As others have written, put protection where the cables would touch, and I would add that protecting under the frame where the rear wheel folds in and makes contact is important too. I used helicopter tape and carefully took note of everywhere the cables touched the frame, both in a folded and unfolded position, plus where the wheel touched the underside of the top tube and the front of the bottom bracket area. But also the tiny tube at the bottom of the rear mudguard because this was very rusty on my old Brompton - that part was the hardest to apply, it would probably have been a lot easier if I had taken the wheel out and could more easily bend the mudguard to make room to get the tape in. After just over a year the tape is still there and you can only see it if you're specifically looking for it so I judge this a success. One more thing - the videos are great!

[@brilliantbikes]

Many thanks! And thanks for watching!

[@64782048]

Wow I was looking at this just last night before I buy my Brompton. There are so many companies in Singapore that does this. Some of their tutorial, they applied soapy water so it is easier to apply the sticker, would you say the same applies here?

[@brilliantbikes]

We did not use soapy water and found it no problem at all to fit! Hope you enjoy your new Brompton

[@ebshaw5974]

A blow dryer helps with those bubbles if they don't go away. Just sweep over sticker and rub bubble towards edge of sticker

[@brilliantbikes]

Many thanks!!! I’ll try it on the one bubble left!

[@JamieWhitehorn]

Great video, we all ❤️ a well protected Brompton 😁 Are you stocking these? If you are, it might be worth putting a link in the description 👍🏻

[@brilliantbikes]

Many thanks, yes we are stocking them. Link to the gloss as follows: brilliantbikes.co.uk/brompton-sundry-parts/5709-bikeshield-full-brompton-kit-gloss.html

[@onebicycle3772]

Hi. Nice informative video. Was wondering if your bicycle shop has already moved to its new location?

[@brilliantbikes]

Many thanks for watching and yes we moved

[@ivanteo1973]

arent you suppose to use soap water and squeegee to press out the bubbles?

[@brilliantbikes]

You can but not takes longer to dry

[@ARlELATOM]

I think the important thing is making sure you protect the frame in all the parts the cables rub the frame.

[@brilliantbikes]

We agree it’s a great solution and thank you for watching!

[@harrypressman2]

Take a sewing needle or pin to pop that little bubble, then press it flat again. Great job by the way.

[@brilliantbikes]

Many thanks! And thanks for watching!

[@AncientYouth64]

can you get a protector to protect the protector?

[@brilliantbikes]

Ah did I get a bit protector protector…. Thanks for watching

[@richardturner81]

Put the stickers on my A-Line today. The headset sticker is for the stem 👍🏻

[@brilliantbikes]

Many thanks for watching! And for letting us know!

[@platypushatstand]

I’d’ve done that with the bike parked, otherwise all,the cables are tight to the frame and you’re making it harder for yourself. My 2012 bike now has too many scratches to be covered (especially the handlepost), though I have covered where the cables rub using an Bikeshield MTB version (it was on sale a few years ago in Evans).

[@nicolasdikenstein6102]

Few years ago I tried to apply the same kind of protection on my singlespeed mtb.. It was so boring to put this protection that I finally let the steel frame without and welcome to a nice 'patine'. I prefer my black brompton in raw mat without this swedish product, personnal choice of course.

[@brilliantbikes]

I was kind of impressed at how easy they were to apply!

[@arcboutant]

A roll of clear 3M tape is what I use on my carbon bikes. Mustn’t let the surface of a carbon frame be damaged as moisture gets in and reeks havoc.

[@brilliantbikes]

Thanks for the suggestion and for watching!

[@jazzfan7491]

Curious how you like that Brooks saddle on that bike. I just bought a C Line "Urban" in Los Angeles. It was supposed to come with that saddle, but it arrived with the stock saddle. My honest feeling is since bike theft is an issue you have to consider in the US, I'm happy to have the stock saddle (I'm assuming it is less attractive to bike thieves)... I should say that Brompton, to their credit, offered to send me the Brooks saddle, but I told them I didn't want it and they should keep the money for themselves. As for frame protection, I put some protective tape on the spot where the cables rub on the frame, but I did that when the bike was folded, then noticed that when unfolded, that rubbing area is in a different spot. Oh well. 🤣

[@brilliantbikes]

Many thanks for watching. It’s a Barbour x Brompton so came with the special edition saddle

[@nicolasdikenstein6102]

I had the original brompton saddle and having pain, never seen worst saddle, I mounted my brooks c15 carved and it's very comfy.

[@MiataBRG]

Was there a top-film that you have to remove after application?

[@brilliantbikes]

No. No top film at all. Thanks for watching!

[@revenFr]

Exactly what I am looking for : just ordered my first Brompton 🥹

[@brilliantbikes]

Andy they are surprisingly easy to apply! Enjoy your new Brompton and have fun naming it!

[@JohnJackson-b7v]

I have just purchased a C Line Explore from you, can you confirm or otherwise if it adheres well to the matt powder coat finish. Many thanks.

[@brilliantbikes]

Many thanks for the question. Sorry I’m not sure what colour you purchased from your user name. Can you let us know.

[@JohnJackson-b7v]

The colour is Cloud Blue. You may like to know that I purchased from you due to your idiosyncratic and excellent videos. Brilliant Bikes were not the nearest or most convenient shop for me but you give give something of value back, I wanted to support it.

[@williamferguson869]

Interesting protectors, looks good, is it very expensive?

[@brilliantbikes]

It’s £62.99 so I kind of think good value

[@letsif]

If you make a mistake, can you peel it off and re apply?

[@brilliantbikes]

Yes it seems OK just try not to get your fingers under it as they will leave marks

[@jeremylim1076]

Nice. But it seems like not enough tape to cover the entire circumference of the tube…? Just seems too small…

[@LaughingStock_]

Why would you want to cover the whole circumference? You only need to protect the parts that are getting chafed.

[@brilliantbikes]

Thanks both, I think it does cover the bits it needs to.

[@jeremylim1076]

@@LaughingStock_ and..??ya it’s a really laughing stock. If it’s really only for chafed then just wrap up the cable with soft material will do… please use a bit of brain juice. If it’s an expensive car , and for paint protection, and u r going to just tell the car owner that u r gonna wrap only the front..? As it only protects stones from the front will do..????

[@edwardshirley9314]

If you get home late after a bad day, all you need to do is watch one of these videos and everything will be alright again😆

[@brilliantbikes]

Thank you so much! Glad we brighten your day 😀

[@jonathanlloyd2306]

Do they sell something to protect the protectors?! 😜💕

[@brilliantbikes]

😂 more protectors?

[@christopherhood9241]

have you tried ridewrap ?

[@ginyamaguchi1421]

Does water get trapped under this if the bike gets wet? I have seen a bike with rust under the protective wrap.

[@wildhogget69]

Product Link? I need these for my new Flame Lacquer Brommie

[@brilliantbikes]

I am surprised how easy they were to install! Link as follows brilliantbikes.co.uk/brompton-sundry-parts/5709-bikeshield-full-brompton-kit-gloss.html Have fun with your new Brompton! Thanks for watching

[@robertoaxelciarelli424]

Interessante📍Sarebbe bello averlo anche colorato📍Interesting📍It would be nice to have it colored too📍

[@brilliantbikes]

They do coloured ones. Just not for a Brompton yet.

[@KavanOBrien]

Did I miss the price? Do you sale them ? Song = Watching Paint Dry = Xrome .

[@brilliantbikes]

Ah we don’t put the price as these can change, yes on the website. Link to the glossy brilliantbikes.co.uk/brompton-sundry-parts/5709-bikeshield-full-brompton-kit-gloss.html Lol on song!

[@KavanOBrien]

@@brilliantbikes Your playlist must be quite extensive with all the songs I’ve sent, didn’t say good but certainly different.

[@stewitwooit9744]

And the price is?

[@brilliantbikes]

£66 Thanks for watching!

[@bobwilliamson5574]

You didn't say how much they cost and where from ?

[@deniscompton7308]

Looks good and I also would like to know if I can buy at the Sunningdale shop .....how much ££££ Denis in Surrey

[@brilliantbikes]

Many thanks. They are £62.99. Yes we normally have them in the shop but sold out of gloss, Matt is in stock. The gloss will be back in next week. Links as follows:: Gloss brilliantbikes.co.uk/brompton-sundry-parts/5709-bikeshield-full-brompton-kit-gloss.html Matt brilliantbikes.co.uk/brompton-sundry-parts/5710-bikeshield-full-brompton-kit-gloss.html

[@stevenheng3336]

Hi, how much it cost?

[@JamieWhitehorn]

£62.99 - they've just added them to their website 👍🏻

[@brilliantbikes]

Many thanks for watching! And for checking!

[@gerlunatorres]

Spraying a mix of water and liquid soap on the frame helps in applying the film because the adhesive will not stick when it is wet; then, pushing the liquid out with a credit card or soft rubber spatula until there are no bubbles or liquid in between and finally let the film dry. I´ve done this when applying a film in glass windows at home. 😀

[@brilliantbikes]

Many thanks! Yes it makes it easier to apply but will take longer to dry

[@pongpong5108]

Is this suitable to use on tline?

[@brilliantbikes]

Sorry this was designed for the C Line, and they don’t have a T Line shaped one yet.

[@CaffeineJogger]

so what's best? you never get to see the Brompton only the plastic protector? Personally I'd rather see the odd scuff or scratch rather than a protective sticker. The scratch or mark, scuff on the bike is part of the story. Would we wear a clear mask our entire lives if it stopped us wrinkling? Nahhh. Great Vid though. Always love these.

[@brilliantbikes]

Thanks for watching! I’m impressed how they do look though!

[@NEAAFFAIRS]

Here in mod craze 🇸🇬 we use car paint protection film.

[@fisharefriends598]

Can believe how cheap they are. I spent nearly £50 to do my road bike and that only really protects the points the frame bags and bike backing bags touch. That bike shied covers a lot of the bike

[@brilliantbikes]

We were kind of impressed with them!

[@BELLAPHONTOO]

I have so little patience for them air bubbles.

[@brilliantbikes]

I was pleased to see them gone!

[@stp926]

Safe Bromptoning. 🙏🏻

[@brilliantbikes]

Many thanks and thanks for watching!

[@lorenzomagni8916]

io la bici la uso cosi come è, e poi se la vernice si rovina la farò riverniciare 😍

[@brilliantbikes]

Many thanks for watching!

[@lorenzomagni8916]

@@brilliantbikes I really like your channel it's very helpful grazie

[@kwhatten]

Better to do in unfolded bike. Btw, generically this is called helicopter tape. Cheaper if you're willing to cut the pieces yourself.

[@brilliantbikes]

Thanks for watching!

[@davidmorgan881]

Save £5,50 a day, in a year you can afford a brand new bike...Far less grief! 😊

[@brilliantbikes]

Lol! But they were kind of easy to install!

[@davidmorgan881]

@@brilliantbikes Bet you were good at the Rubik's cube 😄

[@peterexley4985]

🐝🌏🤞👍 hey good looking good to see you keep safe 🤞

[@brilliantbikes]

Thank you! And thank you for watching!

[@apaul9776]

This product would keep a Brompton looking immaculate because its application is so ridiculously finicky that most people would never complete the task, become overcome with despair and put the bike in hidden part of the garage and try to forget about it.

[@brilliantbikes]

Funny that’s what we thought…. Then we tried them, and they were actually really easy! I was impressed!

[@SingaporeUntold]

Hello Singaporeans. The brompton capital of the world 😅

[@john3892]

Now you can hang the bike on the wall and look at it.

[@brilliantbikes]

😂 very true. But I actually think this is an easy solution to help protect the bike and ride it

[@kr15uk]

Erm, no no no, that’s too much… Slight wear is beautiful, story telling and brings the character. Embrace the reality!

[@Luke-san]

Why o why doesn't this come as standard when you buy an expensive bike like this. Gave this suggestion when I registered both my bikes at Brompton but I guess those suggestions end up nowhere as you don't get any reply at all. It's 50 euro for a serious amount of stress it seems. I would gladly pay 80 euro more for a bike that has these as standard or an option. Most people tend to already have damage when putting these on which is a shame in my opinion.

[@brilliantbikes]

They are really easy to fit. I thought they would be difficult, but really simple. Thanks for the suggestion on adding to new bikes!

[@theflowpowa42oshow]

I'm a cyclepath

[@believe-in-righteousness]

8 would never put any of that on my bike even if it's free

[@LLF1234]

Why not? Do you prefer stone chips and a lot of scratches from the cables and so on?