HOW TO INSTALL REAR CAMBER AND TOE PLATES BMW E30 REAR SUBFRAME BERTY 30 TRACK DRIFT BUILD PART 10

[@harrymatthews8000]

Dude I've been loving the videos lately and I'm excited to see where the bertyE30 is going. I've been religiously watching every single one of your videos and I feel like you should have a crap load more subs anyway thanks

[@tarquineous]

Thanks for explaining toe and camber adjustments! Tips: Ceramic cup on TIG torch can be smaller. Then run 15 to 20 CFH. Saves gas and easier to get into tight areas. Tungsten can be 1/16" for that size weld and material thickness. Smaller tungsten allows more control of arc for that size weld bead. Weld rod is probably 70s2, unless base metal is chrome-moly, then 80s would be appropriate. Use gloves when grinding. Scary.

[@TWRX_Chuck]

I just ordered all my frontend parts to do the E36 work. Front sub frame is coming out for the oil pan so I'm going to do a bunch of suspension refresh.... GitRDone!

[@SpencerHogg]

Them welding skills!! 😍🌚

[@WhiteWingSTI]

It pays to have awesome friends like Arlo there! 👍🏼

[@lookatmatthew6281]

How did these hold up? Im debating between these or the serrated ones. Thanks

[@why_11.]

Thanks for the education videos

[@ayyylmao3586]

Where did you get this kit? Can I get a link

[@esolo4751]

Good job Blake. I need that tig welder tho. I have plenty of projects for it.

[@valwilliams5745]

Hi, great video, just fitting this kit to my M Coupe in the UK right now. However I'm a bit confused with the positioning of the inner camber plates, in your video at 5:26 you suggest bottom most position for less camber and top positon for more; surely it's the other way round?

[@BlakesGarage]

Val Williams inside to the engine for - camber out towards the finders for + camber. Sorry is I kinda made it confusing.

[@TonyCarrillo91]

How close were or are you able to get the camber to 0 degrees with this setup?

[@adamn.9525]

Having been some time since you installed these, have you found the bolts to loosen at all over time and lose your alignment?

[@garykiesel4508]

Personally Ive got my centric camber slots set to only remove as much negative as possible and my serrated toe adjusters the same way because even lowered a little the car has a lot of toe in and negative camber. Also I know centrics can come out of a alignment so with the way I have it it will nvr go more negative that it was stock at that height. Serrated ones don’t Fit it camber spot for raised subframe bushings so I used the centric there and serrated on the toe spot

[@connorplow]

How exactly did you dial in your alignment afterwards? Do you set it up and then guess and check or is there a better way?

[@BlakesGarage]

Took it to get aligned with the new bolts

[@chgotbanned]

I should have done this when my stuff was out, but ill get around to it eventually or just buy the one from garagistic and save time just spend a few more bucks. Get them coils installed already ;)

[@BlakesGarage]

chgotbanned yeah definitely something you want to do just once.

[@e30sdontrun86]

yo amazing video, subscribed

[@visaruttanpruttianunt4220]

Hi, I lowering my car with coilover suspension kit. It make my rear camber -3 degree. If it want set rear camber -1 degree, will I set up or down? Can you suggest position weld plate for toe and camber?

[@visaruttanpruttianunt4220]

I want to know about if I move 1 mm, How many degrees will the angle change?

[@harrymatthews8000]

Also just a tip if you film any sort of welding it will ruin the sensor in your camera think of the sensor as if it were your eyes so just be careful bro

[@BlakesGarage]

Harry Matthews oh snap I didn't realize that. Thanks man.

[@malikebo]

Awesome video and very entertaining . i watch all the e30 one ,since i just bought one . quick question , my e30 is lowered and the camber is -3.00 degree, as far as new bracket , if i want to erase some of negative camber do i go more up to body or down to ground with oval hole in new bracket? thanks again for help.

[@BlakesGarage]

malik ebo if I remember correctly you go up to the body more. Just hold the trailing arm and imagine the change. If it goes up more it should decrease the camber.

[@mallratt25]

Nice work, your welds weren't that bad.

[@BlakesGarage]

+mallratt25 thanks man, yeah I just couldn't get in where I wanted to. My friend is a Union pipe welder so he TIG's stuff all day long and is used to odd angles.

[@ricardogonzalez2977]

I think that the camber and toe plates are easy to do i just don't know where i find the bolts can you post where you buy the kit or are custom made? Searching for this to correct the camber on my e30 :(

[@BlakesGarage]

got them from catuned.com

[@ricardogonzalez2977]

Thanks!

[@fredrikrapp]

Why weld the toe plates in the middle? You will never be wanting to set more toe in on an e30 will you?

[@BlakesGarage]

Fredrik Rapp mostly because I didn’t know where I wanted them. It’s been good for me though.

[@tarquineous]

Fredrik, those tabs are sold in pairs. So the video actually shows the installation of two pairs, one pair for camber, another pair for toe.

[@ajdrifternerd8291]

im trying to wrap my head around camber and toe in your rear is it like trying to adjust a solid axle or am i ove thinking it and it will move the trailing arms as needed and not the sub frame

[@BlakesGarage]

+Nerd Drifter just moves the trailing arms up down left right.

[@ajdrifternerd8291]

i was over thinking it lol

[@Knoss0s]

What happened to your WRX?

[@BlakesGarage]

Knoss0s I still have it. Going to get something new soon.

[@driveshift]

Blake's Garage "getting something new soon" as in replacing the WRX or getting something new to put on the WRX??

[@BlakesGarage]

Marlowe Campos as in replacing the WRX.

[@BlakesGarage]

Marlowe Campos don't worry it will be a very nice car.

[@cameronsousa5572]

how do u not have more subs

[@BlakesGarage]

Cameron Sousa not sure youtube ain't easy.

[@ruvimniz1837]

wrap it mabey orange

[@BlakesGarage]

So close to reaching my goal of 1k followers on Instagram for the month please follow me @blakesgarage for a sneek peaks!

[@manuelriemens3366]

Blake's Garage i follow you

[@TRektsz]

Blake's Garage I came to this channel prepared to storm the comment section with my internet warrior dominance, but I have to say with each video I'm more impressed with your quality of work. Subbed.

[@boost_is_happiness6011]

fu k bud, just get into it .

[@samgh1259]

Thank you very much for your video.