Blues Creek Guitars - Adding Back Strip After Body Assembled

Another Blues Creek Guitars Feature Video on KZbin. This time, How to add a back strip tp your guitar after the body has been assembled.

[@BLJKPLR]

John that was a very good video with instruction. I thought this back strip could be done after the back was sized and glued. I'm not stressing at all doing this now. Thank you for the instruction, I'm always learning.

[@TheForce_Productions]

Beautiful job!

[@joseph2219801]

After I made my first line with my dremel tool I put masking tape on the edge of my router. I had to add more tape a few times but it pushed my router the distance needed. One side of my line was a little deeper so I used my spoke shave to level it.

[@vayabro1]

Clean and beautiful!

[@electricwally]

Spectacular John! Enjoyed and learned a lot!

[@jsdenvir1]

Loved it John. Thanks. Steve.

[@larrysee7306]

Ahh, I get it now, thanks for reply. I searched your channel but couldn’t find any video of replacing an acoustic guitar top. This is an important first step-removing the neck

[@Texstrat721]

John, nice work.

[@patricklundquist9869]

Great work but you really need hearing protection with that little router. Take if from someone with tinnitus. Once you have it, those screaming, squealing tones will never go away. Ever.

[@jamesmedia7247]

Great Stuff!

[@orisguitars7315]

Awesome. Thanks for the videos. You scared me a little on that belt sander

[@mandolinman2006]

I'd be interesting in learning to do the 45 style abalone purfling like on the sides of the body and such.

[@LaSalle.ToneWorks]

+mandolinman2006 that is on the plate. We will do that one but it is not a simple process

[@LiloUkulele]

John, what bit are you using? down cut spiral? What about gluing...seal with shellac and use CA glue?

[@johnhall2795]

this is a 3/32 carbide end mill UP CUT here I would not use a down cut and it is a new fresh bit so its sharp. this is not the place for shellac as rosewood takes CA well . if this were a more porous wood like mahogany I would use Duco the more I do this the less I use CA. I will use CA on rosewood because it is compatible with it.

[@alansauer6853]

just saw this video.That was great.I didn't see it, but you must have used glue. Also,just how deep of a route would be safe too make? I watch all your videos. I appreciate you taking the time to make these.I'm also at your forum,I'm thinking of doing a kit guitar over the winter months.

[@tippie53]

I do about .100 in down

[@brucechumley9195]

John, I've seen other videos of yours wherein you use your inlay cutter. Can you tell us about it? Model/Mfr/Source?

[@tippie53]

you can find this on blues creek guitars I sell them there. The base was modified to cut flush. If you need it to do this let me know .

[@jefferyboring4410]

I’m trying to build a Stella jumbo 12 20s model right now but I need a tracing! Pls can anyone help me? Also maby a line on perfling

[@tippie53]

I think Gurian Instruments has some of the purfling. Not sure where you can find a tracing or plans. You will be looking for the older ones when they were made by Oscar Schmidt I think

[@larrysee7306]

Thanks for all your informative videos. You set the depth on the cutter, but then cut with the base of cutter on top of rules. Did you compensate for this thickness difference, or ?

[@tippie53]

If you look close you will see I was using the rulers straight edge I am not on top of the ruler.

[@LiloUkulele]

How do you set up your router to cut flush along the straight edge...sorry if its a dumb question.

[@johnhall2795]

this isn't a router this is my inaly tool actually it is simple set up cut so you know where the cutter is working in line with the base and bingo. On this tool my base is flush to the cutter so all I need is the straight edge on the back. I may use tape for tweaking the perfect set up. Also note the cutter direction I do this with a climb cut and do multiple cuts

[@GILLEBRATH]

Did I understand you say this guitar is a stella model and is it maple wood ? Thanks John very informative.

[@LaSalle.ToneWorks]

+GILLEBRATH This is actually one of my bodies. Its based off the Old Oscar Schmidt Stella guitars, and is White Oak B&S. Glenn

[@GILLEBRATH]

Thanks. I built up a maple ,similar to yours .,what is B&S?

[@LaSalle.ToneWorks]

+GILLEBRATH Back and Sides

[@GILLEBRATH]

Thanks again

[@budandbean1]

Sure would be great to get some close-ups, I'm not exactly sure what you're doing...

[@LaSalle.ToneWorks]

+Buddy Martin Yes, We had 2 cameras setup sand took close-ups. However, the close-up files got corrupted and they ended up being lost.... we typically do close-ups of all the vids.

[@budandbean1]

+Glenn LaSalle Thank you Glenn, that makes sense. I have just recently found your videos and they are so wonderful, I have subscribed. I'm also excited to go back and watch all your other videos, they also look interesting to watch. Thanks again, Buddy